IBM 8837 - eServer xSeries 336 User manual

IBM xSeries 336
Type 8837
User’s Guide
ERserver


IBM xSeries 336
Type 8837
User’s Guide
ER s e r v e r


Note:
Before using this information and the product it supports, read the general information in Appendix B,
“Notices,” on page 45.
Second Edition (October 2004)
© Copyright International Business Machines Corporation 2004. All rights reserved.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.

Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . .v
Chapter 1. Introducing the xSeries 336 Type 8837 server . . . . . . . .1
Related documentation . . . . . . . . . . . . . . . . . . . . . .1
Notices and statements used in this document . . . . . . . . . . . . . .2
Features and specifications . . . . . . . . . . . . . . . . . . . . .3
What your server offers . . . . . . . . . . . . . . . . . . . . . .4
Reliability, availability, and serviceability . . . . . . . . . . . . . . . .5
Active Memory . . . . . . . . . . . . . . . . . . . . . . . . .6
Memory ProteXion . . . . . . . . . . . . . . . . . . . . . . .6
Memory mirroring and sparing . . . . . . . . . . . . . . . . . . .7
IBM Director . . . . . . . . . . . . . . . . . . . . . . . . . .7
The UpdateXpress program . . . . . . . . . . . . . . . . . . . .8
Server controls, LEDs, and power . . . . . . . . . . . . . . . . . .8
Front view . . . . . . . . . . . . . . . . . . . . . . . . . .8
Operator information panel . . . . . . . . . . . . . . . . . . . .9
Rear view . . . . . . . . . . . . . . . . . . . . . . . . . .12
Server power features . . . . . . . . . . . . . . . . . . . . .13
Chapter 2. Configuring the server . . . . . . . . . . . . . . . . .15
Using the Configuration/Setup Utility program . . . . . . . . . . . . .16
Starting the Configuration/Setup Utility program . . . . . . . . . . . .16
Configuration/Setup Utility menu choices . . . . . . . . . . . . . .16
Passwords . . . . . . . . . . . . . . . . . . . . . . . . .19
Using the Boot menu . . . . . . . . . . . . . . . . . . . . .20
Starting the backup BIOS . . . . . . . . . . . . . . . . . . . .21
Using the ServerGuide Setup and Installation CD . . . . . . . . . . . .21
ServerGuide features . . . . . . . . . . . . . . . . . . . . .22
Setup and configuration overview . . . . . . . . . . . . . . . . .22
Typical operating-system installation . . . . . . . . . . . . . . . .23
Installing your operating system without ServerGuide . . . . . . . . . .23
Configuring the Gigabit Ethernet controller . . . . . . . . . . . . . . .23
Using the baseboard management controller . . . . . . . . . . . . . .24
Enabling and configuring SOL using the OSA SMBridge management utility
program . . . . . . . . . . . . . . . . . . . . . . . . .24
Installing the OSA SMBridge management utility program . . . . . . . .33
Using the baseboard management controller utility programs . . . . . . .35
Using the RAID configuration programs . . . . . . . . . . . . . . . .36
Using the LSI Logic setup utility program . . . . . . . . . . . . . .37
Using ServeRAID Manager . . . . . . . . . . . . . . . . . . .38
Setting up the Remote Supervisor Adapter II SlimLine . . . . . . . . . .39
Requirements . . . . . . . . . . . . . . . . . . . . . . . .39
Cabling the Remote Supervisor Adapter II SlimLine . . . . . . . . . .40
Installing the Remote Supervisor Adapter II SlimLine firmware . . . . . .40
Completing the setup . . . . . . . . . . . . . . . . . . . . .41
Appendix A. Getting help and technical assistance . . . . . . . . . .43
Before you call . . . . . . . . . . . . . . . . . . . . . . . . .43
Using the documentation . . . . . . . . . . . . . . . . . . . . .43
Getting help and information from the World Wide Web . . . . . . . . . .44
Software service and support . . . . . . . . . . . . . . . . . . .44
Hardware service and support . . . . . . . . . . . . . . . . . . .44
© Copyright IBM Corp. 2004 iii

Appendix B. Notices . . . . . . . . . . . . . . . . . . . . . .45
Edition notice . . . . . . . . . . . . . . . . . . . . . . . . .45
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . .46
Important notes . . . . . . . . . . . . . . . . . . . . . . . . .46
Product recycling and disposal . . . . . . . . . . . . . . . . . . .47
Battery return program . . . . . . . . . . . . . . . . . . . . . .47
Electronic emission notices . . . . . . . . . . . . . . . . . . . .48
Federal Communications Commission (FCC) statement . . . . . . . . .48
Industry Canada Class A emission compliance statement . . . . . . . .48
Australia and New Zealand Class A statement . . . . . . . . . . . .49
United Kingdom telecommunications safety requirement . . . . . . . . .49
European Union EMC Directive conformance statement . . . . . . . . .49
Taiwanese Class A warning statement . . . . . . . . . . . . . . .49
Chinese Class A warning statement . . . . . . . . . . . . . . . .50
Japanese Voluntary Control Council for Interference (VCCI) statement . . .50
Power cords . . . . . . . . . . . . . . . . . . . . . . . . . .50
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
iv IBM xSeries 336 Type 8837: User’s Guide

Safety
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d’installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.
© Copyright IBM Corp. 2004 v

Antes de instalar este producto, lea la información de seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
Important:
All caution and danger statements in this documentation begin with a
number. This number is used to cross reference an English caution or
danger statement with translated versions of the caution or danger
statement in the IBM
®
Safety Information book.
For example, if a caution statement begins with a number 1,
translations for that caution statement appear in the IBM Safety
Information book under statement 1.
Be sure to read all caution and danger statements in this
documentation before performing the instructions. Read any additional
safety information that comes with your server or optional device before
you install the device.
vi IBM xSeries 336 Type 8837: User’s Guide

Statement 1:
DANGER
Electrical
current from power, telephone, and communication cables is
hazardous.
To avoid a shock hazard:
v Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical
storm.
v Connect all power cords to a properly wired and grounded electrical
outlet.
v Connect to properly wired outlets any equipment that will be attached to
this product.
v When possible, use one hand only to connect or disconnect signal
cables.
v Never turn on any equipment when there is evidence of fire, water, or
structural damage.
v Disconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
v Connect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached
devices.
To Connect: To Disconnect:
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
1. Turn everything OFF.
2. First, remove power cords from outlet.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
Safety vii

Statement 2:
CAUTION:
When replacing the lithium battery, use only IBM Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has
a module containing a lithium battery, replace it only with the same module
type made by the same manufacturer. The battery contains lithium and can
explode if not properly used, handled, or disposed of.
Do not:
v Throw or immerse into water
v Heat to more than 100°C (212°F)
v Repair or disassemble
Dispose
of the battery as required by local ordinances or regulations.
Statement 3:
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
v Do not remove the covers. Removing the covers of the laser product could
result in exposure to hazardous laser radiation. There are no serviceable
parts inside the device.
v Use of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
DANGER
Some
laser products contain an embedded Class 3A or Class 3B laser
diode. Note the following.
Laser radiation when open. Do not stare into the beam, do not view directly
with optical instruments, and avoid direct exposure to the beam.
viii IBM xSeries 336 Type 8837: User’s Guide

Statement 4:
≥ 18 kg (39.7 lb.) ≥ 32 kg (70.5 lb.) ≥ 55 kg (121.2 lb.)
CAUTION:
Use safe practices when lifting.
Statement 5:
CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current
from the device, ensure that all power cords are disconnected from the power
source.
1
2
Statement 6:
CAUTION:
Do not place any objects on top of a rack-mounted device unless that
rack-mounted device is intended for use as a shelf.
Statement 8:
Safety ix

CAUTION:
Never remove the cover on a power supply or any part that has the following
label attached.
Hazardous voltage, current, and energy levels are present inside any
component that has this label attached. There are no serviceable parts inside
these components. If you suspect a problem with one of these parts, contact
a service technician.
WARNING: Handling the cord on this product or cords associated with accessories
sold with this product, will expose you to lead, a chemical known to the State of
California to cause cancer, and birth defects or other reproductive harm. Wash
hands after handling.
ADVERTENCIA:El contacto con el cable de este producto o con cables de
accesorios que se venden junto con este producto, pueden exponerle al plomo, un
elemento químico que en el estado de California de los Estados Unidos está
considerado como un causante de cancer y de defectos congénitos, además de
otros riesgos reproductivos. Lávese las manos después de usar el producto.
x IBM xSeries 336 Type 8837: User’s Guide

Chapter 1. Introducing the xSeries 336 Type 8837 server
The IBM
®
Eserver
™
xSeries
®
336 Type 8837 server is a 1-U-high
1
rack model
server for high-volume network transaction processing. This high-performance,
symmetric multiprocessing (SMP) server is ideally suited for networking
environments that require superior microprocessor performance, input/output (I/O)
flexibility, and high manageability.
Performance, ease of use, reliability, and expansion capabilities were key
considerations in the design of the server. These design features make it possible
for you to customize the system hardware to meet your needs today and provide
flexible expansion capabilities for the future.
The server comes with a limited warranty. For more information about the terms of
the warranty, see the warranty appendix in the Installation Guide.
The server contains IBM Enterprise X-Architecture
™
technologies, which help
increase performance and reliability. For more information, see “What your server
offers” on page 4 and “Reliability, availability, and serviceability” on page 5.
You can obtain up-to-date information about the server and other IBM server
products at http://www.ibm.com/eserver/xseries/.
For service or assistance information, see Appendix A, “Getting help and technical
assistance,” on page 43.
Related documentation
This User’s Guide provides general information about the server, including
information about features, how to configure the server, and how to get help. In
addition to this User’s Guide, the following documentation comes with the server:
v Installation Guide
This printed document contains instructions for setting up the server and basic
instructions for installing some options.
v Option Installation Guide
This document is in Portable Document Format (PDF) on the IBM xSeries
Documentation CD. It contains detailed instructions for installing, removing, and
connecting optional devices that the server supports.
v Safety Information
This document is in PDF on the IBM xSeries Documentation CD. It contains
translated caution and danger statements. Each caution and danger statement
that appears in the documentation has a number that you can use to locate the
corresponding statement in your language in the Safety Information document.
v Rack Installation Instructions
This printed document contains instructions for installing the server in a rack.
v Hardware Maintenance Manual and Troubleshooting Guide
This document is in PDF on the IBM xSeries Documentation CD. It contains
information to help you solve problems yourself, and it contains information for
service technicians.
1. Racks are marked in vertical increments of 1.75 inches each. Each increment is referred to as a unit, or a “U”. A 1-U-high device
is 1.75 inches tall.
© Copyright IBM Corp. 2004 1

Depending on your server model, additional documentation might be included on
the IBM xSeries Documentation CD.
The server might have features that are not described in the documentation that
you received with the server. The documentation might be updated occasionally to
include information about those features, or technical updates might be available to
provide additional information that is not included in the server documentation.
These updates are available from the IBM Web site. Complete the following steps
to check for updated documentation and technical updates:
1. Go to http://www.ibm.com/pc/support/.
2. In the Learn section, click Online publications.
3. On the “Online publications” page, in the Brand field, select Servers.
4. In the Family field, select xSeries 336.
5. Click Continue.
Notices and statements used in this document
The caution and danger statements that appear in this document are also in the
multilingual Safety Information document, which is on the IBM xSeries
Documentation CD. Each statement is numbered for reference to the corresponding
statement in the Safety Information document.
The following notices and statements are used in this document:
v Notes: These notices provide important tips, guidance, or advice.
v Important: These notices provide information or advice that might help you avoid
inconvenient or problem situations.
v Attention: These notices indicate potential damage to programs, devices, or
data. An attention notice is placed just before the instruction or situation in which
damage could occur.
v Caution: These statements indicate situations that can be potentially hazardous
to you. A caution statement is placed just before the description of a potentially
hazardous procedure step or situation.
v Danger: These statements indicate situations that can be potentially lethal or
extremely hazardous to you. A danger statement is placed just before the
description of a potentially lethal or extremely hazardous procedure step or
situation.
2 IBM xSeries 336 Type 8837: User’s Guide

Features and specifications
The following information is a summary of the features and specifications of the
server. Depending on the server model, some features might not be available, or
some specifications might not apply.
Table 1. Features and specifications
Microprocessor:
v Intel
™
Xeon
®
2.8 GHz or higher
depending on server model
v Support for up to two
microprocessors with Intel
Hyper-Threading Technology and
EM64T (extended memory 64 bit
technology)
v 800 MHz front-side bus (FSB)
Memory:
v Minimum: 512 MB
v Maximum: 16 GB
v Type: 2-way interleaved PC3200,
400 MHz, ECC DDR II SDRAM,
registered DIMMs only
v Sizes: 256 MB, 512 MB, 1 GB, 2
GB (when available)
Expansion
bays:
Comes in 3 configurations:
v Configuration 1 and 2
– Two 3.5-inch hot-swap SCSI or
two 3.5-inch non-hot-swap
(simple swap) SATA hard disk
drives
– One 9.5-mm high DVD-ROM
drive (optional)
v
Configuration 3
– Four 2.5-inch hot-swap SCSI
hard disk drives
Expansion
slots:
v One PCI-X 133 MHz or PCI Ex8,
full-length, full height (Note:
PCI-E x8 (PCI-E) requires an
optional riser card)
v One PCI-X 100 MHz, half length,
low-profile
Power
supply:
v 585 watt hot-swap power supply
standard
v Optional redundant 585 watt power
supply
Size:
v Height: 43 mm (1.69 in.)
v Depth: 686 mm (27.0 in.)
v Width: 440 mm (17.32 in.)
v Weight: approximately 15.6 kg
(34.5 lb) when fully configured or
12.7 kg (28 lb) minimum
Integrated
functions:
v Baseboard management controller
(BMC)
v One LSI Ultra320 SCSI controller
with RAID levels 1 and 1E
capability
v Two Broadcom 10/100/1000
Ethernet controllers with Wake on
LAN
®
feature and Alert Standard
Format support
v Three Universal Serial Bus (USB)
ports
v One serial port
v Keyboard port
v Mouse port
v Video port
Acoustical
noise emissions:
v Sound power, idling: 6.9 bel
maximum
v Sound power, operating: 6.9 bel
maximum
Environment:
v Air temperature:
– Server on: 10° to 35°C (50.0°
to 95.0°F); altitude: 0 to 2133
m (6998.0 ft)
– Server off: 10° to 43°C (50.0°
to 109.4°F); maximum altitude:
2133 m (6998.0 ft)
v
Humidity:
– Server on: 8% to 80%
– Server off: 8% to 80%
Heat output:
Approximate heat output in British
thermal units (Btu) per hour:
v Minimum configuration: 587 Btu/hr
(172 watts)
v Maximum configuration: 1878 Btu/hr
(550 watts)
Electrical
input:
v Sine-wave input (50-60 Hz) required
v Input voltage low range:
– Minimum: 100 V ac
– Maximum: 127 V ac
v
Input voltage high range:
– Minimum: 200 V ac
– Maximum: 240 V ac
v
Input kilovolt-amperes (kVA),
approximately:
– Minimum: .172 kVA
– Maximum: .550 kVA
Notes:
1. Power consumption and heat
output vary depending on the
number and type of optional
features installed and the
power-management optional
features in use.
2. These levels were measured in
controlled acoustical environments
according to the procedures
specified by the American National
Standards Institute (ANSI) S12.10
and ISO 7779 and are reported in
accordance with ISO 9296. Actual
sound-pressure levels in a given
location might exceed the average
values stated because of room
reflections and other nearby noise
sources. The declared sound-power
levels indicate an upper limit, below
which a large number of computers
will operate.
Chapter 1. Introducing the xSeries 336 Type 8837 server 3

What your server offers
Your server uses the following features and technologies:
v Device Driver and IBM Enhanced Diagnostics
To start the Enhanced Diagnostics diagnostic programs, press F2 while the
server is starting.
v Baseboard management controller
The baseboard management controller (BMC) is a service processor that
provides environmental monitoring for the server. If environmental conditions
exceed thresholds or if system components fail, the baseboard management
controller lights LEDs to help you diagnose the problem. Critical errors are also
included in the error log.
v IBM Director
IBM Director is a workgroup-hardware-management tool that you can use to
centrally manage xSeries servers. For more information, see the IBM Director
documentation on the IBM Director CD.
v IBM Enterprise X-Architecture technology
IBM X-Architecture technology combines proven, innovative IBM designs to make
your Intel-processor-based server powerful, scalable, and reliable. For more
information, go to
http://www.ibm.com/pc/us/eserver/xseries/xarchitecture/enterprise/index.html.
– Active
™
Memory
The Active Memory feature improves the reliability of memory through memory
mirroring, and online-spare memory. Memory mirroring stores data in two
pairs of DIMMs simultaneously. Online-spare memory disables a failed pair of
DIMMs from the system configuration and activates a pair of online-spare
DIMMs. For more information, see the section about installing DIMMs in the
IBM xSeries 336 Type 8837 Installation Guide.
– Large system-memory capacity
The memory bus supports up to 16 GB of system memory. The memory
controller supports error correcting code (ECC) for up to eight
industry-standard PC3200, 400 MHz, 1.8 V, 184-pin, registered,
double-data-rate (DDR), synchronous dynamic random access memory
(SDRAM) dual inline memory modules (DIMMs).
– Memory ProteXion
The Memory ProteXion feature provides a function that is similar to a
hot-spare drive in a RAID array. It is based in the memory controller, and it
enables the server to sense when a chip on a DIMM has failed and to route
the data around the failed chip.
v IBM ServerGuide
™
Setup and Installation CD
The ServerGuide Setup and Installation CD that comes with the server provides
programs to help you set up the server and install a 32-bit Windows
®
operating
system. The ServerGuide program detects installed hardware options and
provides the correct configuration programs and device drivers. For more
information about the ServerGuide Setup and Installation CD, see “Using the
ServerGuide Setup and Installation CD” on page 21.
4 IBM xSeries 336 Type 8837: User’s Guide

v Integrated network support
The server comes with an integrated Broadcom Gigabit Ethernet controller, which
supports connection to a 10-Mbps, 100-Mbps, or 1000-Mbps network. For more
information, see “Configuring the Gigabit Ethernet controller” on page 23.
v Large data-storage capacity and hot-swap capability
The server supports up to four 2.5-inch or two 25.4-mm (1-inch) slim-high, 3.5
inch SCSI hot-swap hard disk drives in the hot-swap bays. With the hot-swap
feature, you can add, remove, or replace hard disk drives without turning off the
server.
This server also supports two 25.4-mm (1-inch) slim-high, 3.5-inch SATA simple
swap hard disk drives.
v Light path diagnostics
Light path diagnostics provides LEDs to help you diagnose problems. For more
information, see the section about light path diagnostics in the Installation Guide.
v Redundant connection
The addition of an optional network interface card (NIC) provides failover
capability to a redundant Ethernet connection. If a problem occurs with the
primary Ethernet connection, all Ethernet traffic that is associated with the
primary connection is automatically switched to the redundant NIC. If the
applicable device drivers are installed, this switching occurs without data loss and
without user intervention.
v Redundant cooling and optional power capabilities
The redundant cooling of the fans in the server enables continued operation if
one of the fans fails. The server comes with one 585-watt hot-swap power
supply. You can order a second optional power supply, which provides redundant
power for many server configurations.
v ServeRAID
™
support
The server supports ServeRAID adapters to create redundant array of
independent disks (RAID) configurations.
v Symmetric multiprocessing (SMP)
The server supports up to two Intel microprocessors. If the server comes with
only one microprocessor, you can install an additional microprocessor to enhance
performance and provide SMP capability.
v Systems-management capabilities
The server comes with a baseboard management controller (BMC) installed.
When used with the systems-management software that comes with the server,
you can manage the functions of the server locally and remotely. The BMC also
provides system monitoring, event recording, and dial-out alert capability.
The optional Remote Supervisor Adapter II SlimLine can be used to obtain
enhanced system management capabilities, above those of the embedded BMC.
The Remote Supervisor Adapter II SlimLine, when installed, has a dedicated
Ethernet connection at the rear of the server.
Reliability, availability, and serviceability
Three important computer design features are reliability, availability, and
serviceability (RAS). The RAS features help to ensure the integrity of the data that
is stored in the server, the availability of the server when you need it, and the ease
with which you can diagnose and correct problems.
Your server has the following RAS features:
v Automatic error retry and recovery
Chapter 1. Introducing the xSeries 336 Type 8837 server 5

v Automatic restart after a power failure
v Baseboard management controller (BMC) service processor
v Backup basic input/output system (BIOS) switching under the control of the BMC
v Built-in monitoring for fan, power, temperature, voltage, and power-supply
redundancy
v Cable-presence detection on most connectors
v Chipkill
™
memory protection
v Error codes and messages
v Error correcting code (ECC) L2 cache and system memory
v Hot-swap hard disk drives
v Information and light path diagnostics LED panels
v Menu-driven setup, system configuration, and redundant array of independent
disks (RAID) configuration programs
v Availability of microcode and diagnostic levels
v Parity checking on the small computer system interface (SCSI) bus and PCI
buses
v Power management: Compliance with Advanced Configuration and Power
Interface (ACPI)
v Power-on self-test (POST)
v Predictive Failure Analysis
®
(PFA) alerts
v Redundant Ethernet capabilities with failover support
v Hot-swap cooling fans with speed-sensing capability
v Redundant hot-swap power supplies and redundant hot-swap fans (some
models)
v Remind button to temporarily turn off the system-error LED
v Remote system problem-determination support
v Standby voltage for system-management features and monitoring
v Startup (boot) from LAN through remote initial program load (RIPL) or dynamic
host configuration protocol/boot protocol (DHCP/BOOTP)
v System auto-configuring from the configuration menu
v System error logging (POST and BMC)
v System-management monitoring through the Intra-Integrated Circuit (I
2
C) bus
v Upgradeable POST, BIOS, diagnostics, BMC microcode, and read-only memory
(ROM) resident code, locally or over the LAN
v Vital product data (VPD) on microprocessors, system board, power supplies,
SCSI (hot-swap-drive) backplane, and power backplane
v Wake on LAN feature capability
Active Memory
Active
™
Memory is an IBM feature that improves the reliability of memory through
memory mirroring and the Memory ProteXion
™
feature.
Memory ProteXion
If a detected error is recoverable, the Memory ProteXion feature corrects the error
and rewrites the data to another memory location on the same DIMM. If there are
not sufficient undamaged memory locations that the data can be rewritten to, the
error is unrecoverable. Other conditions can also cause unrecoverable errors. If a
detected error is unrecoverable, light path diagnostics LEDs are lit to indicate the
failing DIMM.
You do not have to enable memory mirroring to use the Memory ProteXion feature.
6 IBM xSeries 336 Type 8837: User’s Guide

Memory mirroring and sparing
Memory mirroring stores data in memory pair 1 and 2 and memory pair 3 and 4
simultaneously. To support memory mirroring, you must install identical dual inline
memory modules (DIMMs) in memory pair 1 and 2 and memory pair 3 and 4. For
more information, see the section about installing memory modules in the Option
Installation Guide on the IBM xSeries Documentation CD.
The server also supports memory sparing; however, the sparing feature is mutually
exclusive with mirroring. The sparing feature disables the failed memory from the
system configuration and activates a memory sparing pair of DIMMs to replace the
failed active DIMM pair.
Before you can enable the memory sparing feature, you must install one additional
pair of DIMMs. The memory sparing DIMM pair must be the same speed, type, and
the same size as or larger, than the active DIMM pair.
To enable memory mirroring or sparing through the Configuration/Setup Utility
program, select Advanced Setup from the main menu, and select Memory
Configuration. For more information about using the Configuration/Setup Utility
program, see “Using the Configuration/Setup Utility program” on page 16.
IBM Director
With IBM Director, a network administrator can:
v View the hardware configuration of remote systems, in detail
v Monitor the usage and performance of critical components, such as
microprocessors, disks, and memory
v Centrally manage individual or large groups of IBM and non-IBM Intel-based
servers, desktop computers, workstations, and mobile computers on a variety of
platforms
IBM
Director provides a comprehensive entry-level workgroup hardware manager. It
includes the following key features:
v Advanced self-management capabilities for maximum system availability.
v Multiple operating-system platform support, including Microsoft
®
Windows 2000
Server, Windows XP Professional, Red Hat Linux, SUSE LINUX, and Novell
NetWare. For a complete list of operating systems that support IBM Director, see
the IBM Director Compatibility Document. This document is in Portable Document
Format (PDF) at http://www.ibm.com/pc/ww/eserver/xseries/
systems_management/nfdir/agent.html. It is updated every 6 to 8 weeks.
v Support for IBM and non-IBM servers, desktop computers, workstations, and
mobile computers.
v Support for systems-management industry standards.
v Integration into leading workgroup and enterprise systems-management
environments.
v Ease of use, training, and setup.
IBM
Director also provides an extensible platform that supports advanced server
tools that are designed to reduce the total cost of managing and supporting
networked systems. By deploying IBM Director, you can achieve reductions in
ownership costs through:
v Reduced downtime
v Increased productivity of IT personnel and users
Chapter 1. Introducing the xSeries 336 Type 8837 server 7

v Reduced service and support costs
For
more information about IBM Director, see the IBM Director CD that comes with
your server, the IBM Director documentation on the CD, and the IBM xSeries
Systems Management Web page at
http://www-1.ibm.com/servers/eserver/xseries/systems_management/
xseries_sm.html, which presents an overview of IBM Systems Management and
IBM Director.
The UpdateXpress program
The UpdateXpress program is available for most xSeries servers and server
options. It detects supported and installed device drivers and firmware in your
server and installs available updates. You can download the UpdateXpress program
from the Web at no additional cost, or you can purchase it on a CD. To download
the program or purchase the CD, go to
http://www.ibm.com/pc/ww/eserver/xseries/serverguide/xpress.html.
Server controls, LEDs, and power
This section describes the controls and light-emitting diodes (LEDs) and how to turn
the server on and off.
Front view
The following illustration shows the controls, LEDs, and connectors on the front of
the server. There are three different front views:
v 2.5-inch SCSI hot-swap hard disk drive
v 3.5-inch SCSI hot-swap hard disk drive
v 3.5-inch SATA non-hot-swap (simple swap) hard disk drive
Note:
Both 3.5-inch configurations support an optional DVD-ROM drive.
The following illustration shows the front view of an IBM xSeries 336 server with a
2.5-inch SCSI hot-swap hard disk drive configuration.
4 x 2.5” Hard disk drives
SCSI ID 1
SCSI ID 0
SCSI ID 3
SCSI ID 2
Hard disk drive activity LED
Hard disk drive status LED
Model #
Serial #
8 IBM xSeries 336 Type 8837: User’s Guide