IBM REDPAPER P5 520 User manual

Quick start guide for p5 520 (9131-52A)
IBM Systems

Rack-mounted devices are not to be used as a shelf or workspace. Do not place
any object on top of rack-mounted devices.
CAUTION: The weight of this part or unit is between 32 and 55 kg (70.5 and
121.2 lb). It takes three persons to safely lift this part or unit. (C010)
The exclamation mark surrounded by a gray triangle denotes caution. A CAUTION
notice indicates the presence of a hazard that has the potential of causing
moderate or minor personal injury. Before doing a step that contains a caution icon,
read and understand the caution statement that accompanies it.
1Before you begin
Use safe practices when lifting.
This Quick start guide contains an abbreviated set of setup instructions designed to help you quickly
unpack and set up a standard system. Users unfamiliar with this IBM hardware should use the fully
detailed, setup instructions that you can find in the IBM Systems Hardware Information Center. For
details about how to access the information center, see task 9 .Finish your system setup
Tools needed (Rack installation only)
Flat-blade screwdriver
32-55 kg (70.5-121.2 lbs)

2.1
2.2
Inventory
Complete an inventory of the external parts.
Locate the kitting report (inventory list) in the bag that contains the information
center CD (SK3T-8159). Make sure you received all of the parts that you ordered.
Your order information should be located in an envelope adhered to the outside of
your system box. You can also obtain order information from your marketing
representative or IBM Business Partner.
If you have incorrect, missing, or damaged parts, consult any of the following
resources:
If you are not installing your server into a rack, skip to task 7
.
Cable the
HMC and the server
Your IBM reseller
IBM Rochester manufacturing automated information
line at 1-800-300-8751 (United States only)
Directory of worldwide contacts at www.ibm.com/planetwide.
Select your location to view the service and support contact information.
2
56
3
1
2
2
4
2
4
1
Rack-mounting template
Slide rail assemblies
Rack-mounting hardware kit
Blue knobs
System-to-slide-rail screws
Rack-retaining screws
Blue thumb screws
Latch brackets
Latch-bracket screws
4
6
4
2
2
2
Cable-management arm
If you are installing your server into a rack, you will need the following parts:

3.1
3.2
3.3
If you are installing your server into a new rack, ensure that you have completed the
unpacking instructions that were provided with the rack.
If your server is already installed in a rack, skip to task 7
Place the rack in the location of the installation.
Use the wrench that was provided with your rack to level the rack by raising or
lowering the front and back leveling feet .
Install the stabilizer bracket on the front of the rack.
If necessary, remove any trim kit pieces that were previously installed on the
rack. Removing the trim kit pieces allows you to read the EIA units on the rack.
A
B
Tip:
Cable the HMC and the
server.
3.4
3Prepare the rack for installation
A
B

4.1
4.2
Locate the rack-mounting template, the rack-mounting hardware kit, and the slide
rail assemblies that were included with your server.
Use the rack-mounting template to determine where in the rack to place the server.
Remove any filler panels necessary to allow adequate access to the location
where you will install your server.
If you do not have enough space around your rack to open the front and back doors
completely, remove the doors before starting this task to allow adequate access.
Install the slide rail assemblies
4
4.3 Follow the rack-mounting template to mark the
location on the rack where you will place the
server. Use the self-adhesive placement dots
found on the rack-mounting template.
Pull the back latch-assembly
release tabs to the retracted
position and lock the latch
assembly . Make sure the
alignment pins that are located
on the back of the slide rail are
fully retracted.
From the back of the rack, insert
the front alignment pin into the
hole in the front of the rack, as
identified by the self-adhesive
placement dot.
C
B
D
D
1.
2.
C
B
Front
Back
A
D
Note: Install units into the lower part of the rack first.
Place larger and heavier units in the lower part of the
rack.
4.4 Install the slide rail assemblies .A

4.6
4.7
4.5
From the front, finger-tighten one of the rack-retaining screws in the first hole
above the front alignment pin .
I
J
From the front, attach the system-unit-
latch bracket by inserting the hook
into the rack hole above the hole
where you will place the latch bracket
screw. Finger-tighten the screw.
K
L
KL
IJ
C
3.
Align the retracted back pins with the holes as identified by the self-adhesive
placement dot. Place the rack flange between the slide-rail flange and the
retracted alignment pins .
Press the back latch-assembly-release tab to extend the back alignment pins into
the back of the rack.
E
FG
E
C
4.
From the back, finger-tighten one of the rack-retaining screws in the hole that
is located between the two back alignment pins .
H
E
4.8 Repeat steps 4.4 through 4.7 for
each slide rail assembly.
Actual size
part 26H7213
Actual size
part 12J5289
F
Actual size
part 12J5289
G
E
H

Actual size
part 04N6485
E
A
B
C
D
F
Before you begin: Read this entire task before completing any individual steps.
5.1
5.2 Fully extend both slide rails.
5.3 Lift the server using the handles on each side and position the server on the
extended slide rails. Align the three holes of the inner slide rails with the three holes
on each side of the server.
C,
D
5.4
5.5 Remove the four blue knobs .B
Use safe practices when lifting.
Attach the four blue knobs to the server The blue knobs are used temporarily
to rest the server on the slide rails for installation. These knobs will be removed after
the server is secured to the slide rails.
BA.
Install the server onto the slide rail assembly
5
Before installing the server onto the slide rail assembly, ensure that the
leveling feet are extended and that the stabilizer bracket is correctly installed
to prevent the rack from falling forward.
Using a screwdriver, attach the inner slide
of the slide rails to each side of the
server by using the system-to-slide-rail
screws . Use a screwdriver to tighten
each of the screws.
D
E
5.7 Using a screwdriver, tighten the two rack-retaining screws to secure the slide rails to
the back of the rack.
5.6 Simultaneously release the blue safety
latches located near the front of each
slide rail assembly, and slowly push the
server back into the rack.
F
5.8 Slide the server part of the way out of the rack. Using a screwdriver, tighten the front
two rack-retaining screws and the two latch-bracket screws on the front of the rack to
secure the slide rails.
32-55 kg (70.5-121.2 lbs)
Tip: Pull the server back out and push it in again to make sure that the slide
rails are aligned correctly and that it glides smoothly.

6Install the cable-management arm
B
C
DE
A
6.3
From the back of the rack, use the pin to affix the cable-management arm to the
left slide-rail management arm flange that is attached to the rack frame .
AE
D-
6.1 Locate the cable-management arm and the two pins .EA
6.2
Use the second pin to affix the other end of the cable-management arm to the
flange that is attached to the sliding portion of the left slide rail assembly .
A
CB
E
Tip: If space is limited inside the rack, slide the server out part of the way to install the
cable-management arm.

7.1
7.2
7.3
Route the power cords through the rings or clamps on the
back of the server, and connect to the server, monitor, and HMC.
, if available,
Do
not connect the power cords to a power source until instructed to
do so.
7.4 Attach the monitor cable to the monitor connector on the HMC
and tighten the screws.
Tip: If you are using the rack-mounted LCD monitor and
keyboard (7316-TF3), use the C2T-to-KVM adapter breakout
cable to attach to the HMC.
A Hardware Management Console (HMC) is a system that connects to the server and manages it
through a network.
If you are using a rack-mounted HMC, these steps assume it is already installed in the rack.
If you need to install the HMC into the rack, follow the instructions in the IBM Systems Hardware
Information Center, and return to this guide when you are ready to begin cabling your HMC. For details
about how to access the information center, see task 9
If you are not using an HMC to manage your server, you can use the Integrated
Virtualization Manager (IVM), a graphics terminal, or an ASCII terminal. If you plan to use
IVM, which allows you to create and manage partitions, skip to task 8
. For information about the other console
options, go to the IBM Systems Hardware Information Center. For details about how to
access the information center, see task 9 .
Cable the server and
access the Integrated Virtualization Manager
Finish your system setup
Finish your system setup.
If you are using any optional adapters for the HMC, connect the cables to the
appropriate adapter connectors in the PCI slots of your server and HMC.
Cable the HMC and the server
7
Important: Ensure that if there is a voltage switch next to the power
connector on the monitor, it is in the appropriate position for the voltage used
in your geography.
Connect the mouse and keyboard cables to the appropriate ports on the
back of the HMC. If your mouse and keyboard use Universal Serial Bus
(USB) cables, you can connect these to the ports on the front of the HMC.

7.5
7.6
If you are not using a modem, skip to step 7.6.
If you are using the integrated HMC modem, connect the telephone cable to
the modem and to the analog jack on the wall. If you are using an external
modem, connect the modem data cable to the external modem and to a serial
port on the HMC. Then connect the telephone cable to the external modem
and to the analog jack on the wall.
Connect the Ethernet cable to the Ethernet port on the HMC and to
the Ethernet port labeled HMC1 on the server.
For a stand-alone HMC, use the integrated Ethernet port. For the 7310-CR2
rack-mounted HMC, use the bottom-right Ethernet port. For the 7310-CR3 rack-
mounted HMC, use the left port of the two planar board Ethernet ports.
7.7
7.8
7.9
If using an external modem, plug the power cord into the modem.
Plug the power cords for the monitor, HMC, and external modem into a power
source. Do not connect the server to a power source until instructed to do so.
CAUTION: This product is equipped with a 3-wire (two conductor and a
ground) power cable and plug. Use this power cable with a properly
grounded electrical outlet to avoid electrical shock. (C018)
You have completed the basic setup. Go to task 9 Finish your system setup.
Route the cables through the cable-management arm on the server and
secure the cables with the straps provided.
7.12
7.10
7.11
Start and configure the HMC, which includes the Guided Setup Wizard. You can
find the instructions for configuring the HMC in the IBM Systems Hardware
Information Center. For details about how to access the information center, see
task 9 Finish your system setup.
Connect the server to a power source and wait for the control panel on the front of
the server to display This might take several minutes..01
Press the white Power On button on the control panel.

8.1
8.2
Connect one end of a serial cable to the system port on your server, and the other
end to a serial port on a PC that has Microsoft Internet Explorer 6.0, Netscape 7.1, or
Opera 7.23 installed.
8
Connect an Ethernet cable from the PC to the port labeled HMC1 on the back of
the server. If HMC1 is occupied, use the port labeled HMC2.
If you are using any optional adapters, connect the cables to the appropriate
adapter connectors in the PCI slots of your server and PC.
Cable the server and access the Integrated
Virtualization Manager
CAUTION: This product is equipped with a 3-wire (two conductors and a
ground) power cable and plug. Use this power cable with a properly
grounded electrical outlet to avoid electrical shock. (C018)
Route the power cords through the rings or clamps, if available, on the back of the
server, and connect the server to a power source. Wait for the control panel on the
front of the server to display . This might take several minutes.01
8.3
8.4

8.8
8.6
At the login prompt, enter the following default user ID and password:
In the navigation area, expand .
Click .
Select in the Boot to system server firmware field.
Click .
Power/Restart Control
Power On/Off System
Standby
Save settings and power on
User ID
admin
Password
admin
Configure the Ethernet interface on the PC to an IP address and subnet mask
within the same subnet as the server. This is the IP address for the service
processor.
Server connector
HMC1
HMC2
Subnet mask
255.255.255.0
255.255.255.0
IP address
192.168.2.147
192.168.3.147
For example, if you connected your PC to HMC1, the IP address for your service
processor might be 192.168.2.1 and the subnet mask would be 255.255.255.0. Set
the gateway IP address to the same IP address as that of the PC.
Using a Web browser, enter the IP address into the field that corresponds
to the port to which your PC is connected. For example, enter https://192.168.2.147.
Address
Possible values:
Note:If you do not know how to do this, see the instructions in the IBM Systems
Hardware Information Center. For details about how to access the information
center, see task 9 Finish your system setup.
When you are prompted, change the default password.
8.7
8.10
8.9
1.
2.
3.
4.
Change the state of the system server firmware.
8.5 If this server is installed in a rack, route the cables through the cable-
management arm and secure the cables to the cable-management arm.

8.12
Open a terminal session on the PC, using an application such as
HyperTerminal, and wait for the SM’s menu to appear. Be sure the line speed
is set to 19,200 bits per second to communicate with the system.
8.15
Change the partition mode.
Insert the Virtual I/O Server CD into the optical drive of the system.
1.
2.
3.
4.
5.
In the navigation area, expand .
Click .
Select in the AIX/Linux partition mode boot field.
Select in the Boot to system server firmware field.
Click .
Power/Restart Control
Power On/Off System
Boot to SMS menu
Running
Save settings and continue system server firmware boot
8.13
1.
2.
3.
4.
In the ASMI navigation area, expand .
Click .
Select in the AIX/Linux partition mode boot field.
Click .
Power/Restart Control
Power On/Off System
Continue to operating system
Save settings
8.14 Change the partition mode back so that the server continues to load the operating
system during startup.
8.11 After the system has reached the firmware standby state, enter the activation
code for the Virtualization Engine technologies.
TM
In the navigation area, expand .
Click .
Enter the activation key into the field. This key was included with the printed
material inside your system box.
Click . The Advanced POWER Virtualization feature is enabled.
On Demand Utilities
CoD Activation
Continue
1.
2.
3.
4.

1.
2.
3.
4.
Select the console, and press Enter.
Select a language for the BOS menus, and press Enter.
Select .
Select . The managed system restarts after the
installation is complete, and the login prompt is displayed on the ASCII
terminal.
Start Install Now with Default Settings
Continue with Install
8.17 Install the Virtual I/O Server.
8.16 When the system management services (SMS) menu is displayed in the
terminal session over the connection that you set up in step 8.1, choose
and follow the menu options to set the optical drive as
the initial boot device.
Select Boot Options
Tip: Additional Information about the Virtual I/O Server, such as how to check for
updates, configure network connections, and configure partitions, is located in the
IBM Systems Hardware Information Center.
You have completed the basic setup. Continue to task 9 Finish your system setup.

Finish your system setup
9
Using a Web browser, go to www.ibm.com/systems/infocenter/hardware or go to
the preinstalled version on the HMC.
Answer the questions in the interactive interview, and follow the procedures in the
resulting checklist.
From the navigation bar, click Systems Hardware information System p
information > Initial server setup Create a customized initial server setup
checklist.
>
>
You have completed the basic tasks to set up your server.
access the . Follow these steps to create a
customized checklist that helps configure your server and console, install software, apply fixes, and
establish connections with your service provider:
You can now IBM Systems Hardware Information Center
If you cannot access the online version of the information center, it is also provided
on a CD with your system (SK3T-8159).
9.1
9.2
9.3

International Business Machines Corporation 2005, 2007
Printed in USA
September 2007
All Rights Reserved
Mail comments to:
IBM Corporation
Attention Department DDR
3605 Highway 52 North
Rochester, MN U.S.A. 55901-7829
Fax comments to:
1-800-937-3430 (U.S. or Canada)
1-507-253-5192 (outside the U.S. or Canada)
Internet URL: http://www.ibm.com/systems/infocenter/hardware
References in this publication to IBM products or
services do not imply that IBM intends to make
them available in every country or region.
IBM, the IBM logo, and System p are trademarks of
International Business Machines Corporation in the United
States, other countries or both.
Microsoft, Windows, Windows NT, and the Windows
logo are trademarks of Microsoft Corporation in
the United States, other countries, or both.
Other company, product, and service names may
be trademarks or service marks of others.
SA41-5166-04
29R1713