Icom IC-U80 User manual

INSTRUCTION MANUAL
iU80
iU80 E
UHF TRANSCEIVER

i
FOREWORD
Thank you for purchasing this fine Icom product. The IC-U80/
IC-U80E u h f t r a n s c e i v e r is designed and built with Icom’s
superior technology and craftsmanship. With proper care,
this product should provide you with years of trouble-free op-
eration.
We appreciate you making the IC-U80/IC-U80E your radio of
choice, and hope you agree with Icom’s philosophy of “tech-
nology first.” Many hours of research and development went
into the design of your IC-U80/IC-U80E.
FEATURES
❍Dust-protection/Splash-resistant construc-
tion (IP54*)
*Only when the battery pack or case, antenna and jack cover are
attached.
❍Built in VOX circuit enabling the VOX op-
eration* (voice operated transmission)
*To use the VOX operation, an optional headset and a plug
adapter cable are required.
EXPLICIT DEFINITIONS
WORD DEFINITION
RDANGER! Personal death, serious injury or an ex-
plosion may occur.
RWARNING! Personal injury, fire hazard or electric
shock may occur.
CAUTION Equipment damage may occur.
NOTE Recommended for optimum use. No risk
of personal injury, fire or electric shock.
IMPORTANT
READ ALL INSTRUCTIONS carefully and completely
before using the transceiver.
SAVE THIS INSTRUCTION MANUAL— This in-
struction manual contains important operating instructions
for the IC-U80/IC-U80E.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom
Incorporated (Japan) in Japan, the United States, the United King-
dom, Germany, France, Spain, Russia and/or other countries.
Microsoft, Windows and Windows Vista are registered trademarks of
Microsoft Corporation in the United States and/or other countries.

ii
RDANGER! NEVER short the terminals of the battery pack.
RDANGER! Use and charge only specified Icom battery
packs with Icom radios or Icom chargers. Only Icom battery packs
are tested and approved for use with Icom radios or charged with
Icom chargers. Using third-party or counterfeit battery packs or
chargers may cause smoke, fire, or cause the battery to burst.
RWARNING RF EXPOSURE! This device emits
Radio Frequency (RF) energy. Caution should be observed
when operating this device. If you have any questions regard-
ing RF exposure and safety standards, please refer to the
Federal Communications Commission Office of Engineering
and Technology’s report on Evaluating Compliance with FCC
Guidelines for Human Radio Frequency Electromagnetic
Fields (OET Bulletin 65).
RWARNING! NEVER hold the transceiver so that the
antenna is very close to, or touching exposed parts of the
body, especially the face or eyes, while transmitting. The
transceiver will perform best if the microphone is 5 to 10 cm (2
to 4 inches) away from the lips and the transceiver is vertical.
RWARNING! NEVER operate the transceiver with a
headset or other audio accessories at high volume levels.
Hearing experts advise against continuous high volume op-
eration. If you experience a ringing in your ears, reduce the
volume level or discontinue use.
RWARNING! NEVER operate the transceiver while
driving a vehicle. Safe driving requires your full attention—
anything less may result in an accident.
RWARNING! NEVER operate or touch the transceiver
with wet hands. This may result in an electric shock or may
damage the transceiver.
CAUTION: MAKE SURE the antenna and battery pack
are securely attached to the transceiver, and that the antenna
and battery pack are dry before attachment. Exposing the in-
side of the transceiver to water will result in serious damage
to the transceiver.
DO NOT operate the transceiver near unshielded electrical
blasting caps or in an explosive atmosphere.
DO NOT push [PTT] unless you actually intend to transmit.
BE CAREFUL! The transceiver will become hot when
continuously operating it for long periods of time.
DO NOT use or place the transceiver in direct sunlight,
or in areas with temperatures below –20°C (–4˚F) or above
+60°C (+140˚F).
Place the unit in a secure place to avoid inadvertent use by
children.
PRECAUTIONS

iii
SUPPLIED ACCESSORIES
The following accessories are supplied with the transceiver.
PRECAUTIONS
DO NOT use harsh solvents such as benzine or alcohol when
cleaning, as they will damage the transceiver’s surfaces.
DO NOT disassemble or modify the transceiver for any rea-
son.
KEEP the transceiver away from heavy rain, and never im-
merse it in water. The transceiver meets IP54* requirements
for dust-protection and splash resistance. However, once the
transceiver has been dropped, dust-protection and splash re-
sistance cannot be guaranteed because of possible damage
to the transceiver’s case or the waterproof seal.
* Only when the battery pack or case, antenna and jack cover are
attached.
Even when the transceiver power is OFF, a slight current still
flows in the circuits. Remove the battery pack or batteries
from the transceiver when not using it for a long time. Other-
wise, the installed battery pack or batteries will become ex-
hausted, and will need to be recharged or replaced.
Antenna*
Battery pack*
Belt clip* Jack cover
(with screws)
Battery charger*
AC adapter*
* Not supplied, or the shape may be different,
depending on the version.

iv
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
TABLE OF CONTENTS
FOREWORD ..................................................................................... i
FEATURES........................................................................................ i
EXPLICIT DEFINITIONS................................................................... i
IMPORTANT...................................................................................... i
PRECAUTIONS............................................................................ii–iii
SUPPLIED ACCESSORIES............................................................ iii
TABLE OF CONTENTS............................................................... iv–v
1 ACCESSORIES...........................................................1–2
 ■ Antenna ...................................................................................1
 ■ Belt clip ....................................................................................1
 ■ Battery pack or case................................................................2
 ■ Jack cover................................................................................2
2 PANEL DESCRIPTION................................................3–7
 ■ Front, top and side panels .......................................................3
 ■ Function display.......................................................................6
3 BATTERY CHARGING ..............................................8–14
 ■ Caution (for the BP-264 Ni-MH battery) ................................... 8
 ■ Caution (for the BP-265 Li-ion battery)....................................9
 ■ Battery chargers ....................................................................11
 ■ Battery case (BP-263) ...........................................................14
 ■ Battery information ................................................................14
4 BASIC OPERATION................................................15–20
 ■ Power ON ..............................................................................15
 ■ Adjusting the volume level .....................................................15
 ■ Adjusting the squelch level ....................................................15
 ■ Monitor function .....................................................................15
 ■ Mode selection.......................................................................16
 ■ Operating mode selection......................................................17
 ■ Setting a tuning step..............................................................17
 ■ Setting a frequency................................................................17
 ■ Key lock function....................................................................18
 ■ Receiving...............................................................................18
 ■ Transmitting............................................................................19
 ■ [VOL] function assignment.....................................................20
5 REPEATER AND DUPLEX OPERATION ...............21–24
 ■ Repeater operation................................................................21
 ■ Duplex operation....................................................................22
 ■ Subaudible tones ................................................................... 23
 ■ Lockout function.....................................................................24
6 MEMORY/CALL OPERATION ................................25–29
 ■ General description................................................................25
 ■ Selecting a memory channel .................................................25
 ■ Selecting the Call channel .....................................................25
 ■ Programming channels..........................................................26
 ■ Copying memory/Call contents..............................................27
 ■ Clearing memory contents.............................................................28
 ■ Display type ...........................................................................28
 ■ Programming a channel name .................................................29

New2001New2001
v
7 SCAN OPERATION.................................................30–32
 ■ Scan types.............................................................................30
 ■ Programmed scan ................................................................30
 ■ Memory Scan ........................................................................31
 ■ Setting Skip channels ............................................................31
 ■ Scan resume setting..............................................................31
 ■ Priority watch .........................................................................32
8 TONE SQUELCH AND POCKET BEEP .......................33
 ■ Tone/DTCS squelch and pocket beep....................................33
 ■ Tone scan...............................................................................35
9 DTMF MEMORY ............................................................36
 ■ Programming a DTMF code sequence..................................36
 ■ Transmitting a DTMF code sequence ....................................37
 ■ Confirming a DTMF memory .................................................38
 ■ Setting DTMF transfer speed.................................................38
10 SET MODES..................................................................39
 ■ Set mode programming .........................................................39
 ■ Set mode items......................................................................40
 ■ Initial Set mode programming................................................... 44
 ■ Initial Set mode items ............................................................45
11 CLONING ......................................................................50
 ■ Cloning operation...................................................................50
12 RESETTING ..................................................................51
 ■ Resetting................................................................................51
13 TROUBLE SHOOTING..................................................52
14 OPTION .........................................................................53
 ■ VOX function ..........................................................................55
15 SPECIFICATIONS .........................................................57
TABLE OF CONTENTS

New2001
1
1
ACCESSORIES
New2001
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
■Antenna
Insert the antenna into the antenna connector, and then twist
the antenna base to lock it in place.
CAUTION:
• NEVER HOLD just the antenna when carrying the trans-
ceiver.
• Transmitting without an antenna will damage the trans-
ceiver.
■Belt clip
To attach the belt clip:
Slide the belt clip in the direction of the arrow until the belt
clip locks in place, and makes a ‘click’ sound.
To detach the belt clip:
qRemove the battery pack or case from the transceiver, if it
is attached. (p. 2)
wLift the tab up (q), and slide the belt clip in the direction
of the arrow (w).
Belt clip
Battery pack/case
q
w

New2001New2001
2
1ACCESSORIES
New2001
■Battery pack or case
To attach the battery pack or case:
qFit the battery pack or case in the direction of the arrow,
then close it.
wHook the latch until it makes a ‘click’ sound.
w
q
Latch
Battery pack/case
To remove the battery pack or case:
Be careful! The latch is tightly locked, so use caution
when releasing it. DO NOT use your finger nail. Use the
edge of a coin or screwdriver tip to carefully release it.
qUnhook the latch.
w Lift up the battery pack or case in the direction of the arrow.
q
w
NEVER remove or attach the battery pack or case when
the transceiver is wet or soiled. This may result in water or
dust getting into the transceiver/battery pack or case, and
may result in them being damaged.
NOTE: Keep the battery terminals clean. It’s a good idea
to clean the battery terminals once a week.
■Jack cover
Attach the jack cover when optional equipment is not used.
To attach the jack cover
qAttach the jack cover to
the [SP MIC] jack.
wTighten the screws.
To detach the jack cover
qRemove the screws with a
phillips screwdriver.
wDetach the jack cover to
connect optional equip-
ment.
w
w
q
q
q
w

New2001
3
2
PANEL DESCRIPTION
New2001
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
■Front, top and side panels
qPTT SWITCH [PTT]
Hold down to transmit, release to receive. (p. 19)
wANTENNA CONNECTOR
Connect the antenna here. (p. 1)
eCONTROL DIAL [VOL]
➥Adjust the volume level. (p. 15)
➥During the Set mode, or Initial Set mode, rotate to se-
lect a desired option or value. (pp. 39, 44)
r EXTERNAL SPEAKER/MICROPHONE JACKS [SP MIC]
Used to connect an optional speaker-microphone, plug
adapter cable or cloning cable. The internal microphone
and speaker will not function when an option is connected.
See page 53 for a list of available options.
Be sure to turn OFF the transceiver power before con-
necting or disconnecting optional equipment to or from
the [SP MIC] jack.
tMONITOR KEY [MONI]
➥Hold down to temporarily open the squelch to monitor
the operating frequency. (p. 15)
➥While holding down this key, push [p]or [q]to adjust
the squelch level. (p. 15)
➥Enters or sends the DTMF code ‘A.’ (pp. 36, 37)
q
we
r
t
y
u
i
Function
display (pp. 6, 7)
Keypad
(pp. 4, 5)
Microphone
Speaker

4
2PANEL DESCRIPTION
New2001 New2001
■Front, top and side panels (Continued)
yPOWER KEY [ ]
Hold down for 1 second to turn the transceiver power ON
or OFF. (p. 15)
uUP/DOWN KEYS [p]/[q]
➥Push to change the operating frequency. (p. 17)
➥During memory mode operation, push to select a mem-
ory channel. (p. 25)
➥While scanning, push to change the scanning direction.
(pp. 30, 31, 32, 35)
➥While holding down [MONI], push to set the squelch
level. (p. 15)
➥While in the Set mode, or Initial Set mode, push to se-
lect a desired setting item. (pp. 39, 44)
➥[p] enters or sends the DTMF code ‘B.’ (pp. 36, 37)
➥[q] enters or sends the DTMF code ‘C.’ (pp. 36, 37)
iVFO/MEMORY/CALL KEY [VFO/MR/CALL]
➥Push to sequentially select the VFO mode, memory
mode or a Call channel. (p. 16)
➥After pushing [FUNC](M), push to enter the memory
programming mode.
➥After pushing [FUNC](M), hold down for 1 second to
copy a channel contents to a memory channel, or to the
VFO mode. (p. 27)
➥Enters or sends the DTMF code ‘D.’ (pp. 36, 37)
The functions of [VOL] and [p]/[q]can be exchanged.
See page 20 for details.
DKEYPAD
➥Push to input numbers for frequency input and to select
memory channels.
➥Push to enter or send the DTMF code. (pp. 36, 37)
➥Pushing these keys, after pushing [FUNC](M), activates
the key’s second function.
[1] • [ TONE](1)
➥Numeric input and sends DTMF code: ‘1’
➥After pushing [FUNC](M), selects the Tone func-
tion. (p. 34)
[2] • [VOX](2)
➥Numeric input and sends DTMF code: ‘2’
➥After pushing [FUNC](M), turns the VOX function*
ON or OFF. (p. 55)
* Only when an optional headset and plug adapter are con-
nected.

New2001
5
2
PANEL DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
[3] • [T.SCAN](3)
➥Numeric input and sends DTMF code: ‘3’
➥After pushing [FUNC](M), starts a tone scan. (p.
35)
[4] • [DUP](4)
➥Numeric input and sends DTMF code: ‘4’
➥After pushing [FUNC](M), selects minus duplex,
plus duplex, or simplex operation. (p. 22)
[5] • [SCAN](5)
➥Numeric input and sends DTMF code: ‘5’
➥After pushing [FUNC](M), starts a scan. (pp. 30,
31)
[6] • [SKIP](6)
➥Numeric input and sends DTMF code: ‘6’
➥After pushing [FUNC](M), sets or cancels the
Memory Skip scan setting. (p. 31)
[7] • [PRIO](7)
➥Numeric input and sends DTMF code: ‘7’
➥After pushing [FUNC](M), starts the Priority watch.
(p. 32)
[8] • [SET](8)
➥Numeric input and sends DTMF code: ‘8’
➥After pushing [FUNC](M), enters the Set mode.
(p. 39)
[9] • [H/M/L](9)
➥Numeric input and sends DTMF code: ‘9’
➥After pushing [FUNC](M), sets the output power
to High, Mid or Low. (p. 19)
[0] • [DTMF-M](0)
➥Numeric input and sends DTMF code: ‘0’
➥After pushing [FUNC](M), enters the DTMF mem-
ory mode. (p. 36)
[M] • [FUNC](M)
➥Sends DTMF code: ‘M(indication: E)’
➥Push to access the second function of other
keys.
[# ENT] • [ ](ENT)
➥Sends DTMF code: ‘#(indication: F)’
➥After entering a frequency, stores it. (p. 17)
➥Push to exit the Set mode or Initial Set mode. (pp.
39, 44)
➥ After pushing [FUNC] (M) , hold down for 1 second
to turn the Key Lock function ON or OFF (p. 18)

6
2PANEL DESCRIPTION
New2001 New2001
■Function display
qBUSY ICON
➥Appears when a signal is being received, or the squelch
is open.
➥Blinks while the monitor function is ON. (p. 15)
wSIGNAL ICONS
➥Shows the strength of the received signal. (p. 18)
➥While transmitting, shows the output power level. (p. 19)
eTONE ICONS
➥“ ”: While the repeater tone encoder is ON. (p. 21)
➥“ ”: While the tone squelch function is ON. (p. 34)
➥“
D
”: While the DTCS squelch function is ON. (p. 34)
➥“
D
” and “ ”: While the DTCS encoder is ON. (p. 34)
➥“ ” and “ ” or “
D
”: While the pocket beep function (with
CTCSS or DTCS) is ON. (p. 34)
rMEMORY ICON
Appears when the memory mode is selected. (pp. 16, 25)
tFREQUENCY READOUT
➥Displays the operating frequency, memory channel, Set
modes contents and a variety of other information.
• The decimal point blinks during scan.
➥During memory mode operation, the programmed
memory name is displayed.
yBATTERY ICONS (p. 14)
➥“ ” (battery icons) appear when the battery pack or
case is attached.
➥“ ” appears when the battery is nearing exhaustion.
Charging the battery pack, or replacing the batteries in
the case is necessary.
uKEY LOCK ICON
Appears when the Key Lock function is ON. (p. 18)
iVOX ICON
Appears when the VOX function is ON. (p. 55)
Weak RX Signal level Strong
Low Mid High
u
i
o
q w e r y
t
!5
!4
!3
!1
!2 !0

New2001
7
2
PANEL DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
oPOWER ICONS (p. 19)
➥“H” appears when High power is selected.
➥“M” appears when Mid power is selected.
➥“L” appears when Low power is selected.
!0MEMORY CHANNEL NUMBER
➥Displays the selected memory channel number. (p. 25)
➥“C” appears when the Call channel is selected. (p. 25)
!1AUTO POWER OFF ICON
Appears when the Auto Power-OFF function is ON. (p. 45)
!2DUPLEX ICONS (p. 22)
➥“+” appears when plus duplex is selected.
➥“–” appears when minus duplex is selected.
!3SKIP ICON
Appears when the selected memory channel is set as a
Skip channel. (p. 31)
!4FUNCTION ICON
Appears when the second function is accessed.
!5TRANSMIT ICON
Appears while transmitting. (p. 19)

8
BATTERY CHARGING
3
■Caution (for the BP-264 Ni-MH battery)
RDANGER! NEVER short the terminals (or charging termi-
nals) of the battery pack. Also, current may flow into nearby
metal objects such as a necklace, so be careful when plac-
ing battery packs (or the transceiver) in handbags, etc.
Simply carrying with or placing near metal objects such as
a necklace, etc. may cause shorting. This may damage not
only the battery pack, but also the transceiver.
RDANGER! NEVER incinerate used battery packs. Internal
battery gas may cause an explosion.
RDANGER! NEVER immerse the battery pack in water.
If the battery pack becomes wet, be sure to wipe it dry BE-
FORE attaching it to the transceiver.
CAUTION: Always use the battery within the specified tem-
perature range, –5˚C to +60˚C (+23˚F to +140˚F). Using the
battery out of its specified temperature range will reduce the
battery’s performance and battery life.
CAUTION: Shorter battery life could occur if the battery is
left completely discharged, or in an excessive temperature
environment (above +55˚C; +131˚F) for an extended period
of time. If the battery must be left unused for a long time,
it must be detached from the radio after charging. Keep it
safely in a cool dry place at the following temperature range:
–20˚C to +45˚C (–4˚F to +113˚F) (up to a month)
–20˚C to +35˚C (–4˚F to +95˚F) (up to six months)
–20˚C to +25˚C (–4˚F to +77˚F) (up to a year*)
* We recommend charging the battery pack every 6 months.
Clean the battery terminals to avoid rust or misscontact.
Keep the battery terminals clean. It’s a good idea to clean
the battery terminals once a week.
If your Ni-MH battery pack seems to have no capacity, even
after being charged, completely discharge it by leaving the
power ON overnight. Then, fully charge the battery pack again.
If the battery pack still does not retain a charge (or only very lit-
tle charge), a new battery pack must be purchased. (p. 53)
Prior to using the transceiver for the first time, the battery
pack must be fully charged, for optimum life and operation.
• Recommended temperature range for charging:
between +10°C (+50˚F) and +35°C (+95˚F) (rapid charge:
with BC-191, BC-197) or between 0°C (+32˚F) and +45°C
(+113˚F) (regular charge: with BC-192)
• Use only the supplied charger or optional charger (BC-191,
BC-197 for rapid charging, BC-192 for regular charging).
NEVER use other manufacturers’ chargers.
The battery pack contains a rechargeable battery.
Charge the battery pack before first operating the trans-
ceiver, or when the battery pack becomes exhausted.
If you want to prolong the battery life, the following points
should be observed:
• DO NOT overcharge the battery pack. The charging time
period should be less than 48 hours.
• Use the battery pack until it becomes almost completely
exhausted, under normal conditions. We recommend bat-
tery charging after transmitting becomes impossible.

9
2
3
BATTERY CHARGING
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
■Caution (for the BP-265 Li-ion battery)
RDANGER! NEVER short the terminals (or charging termi-
nals) of the battery pack. Also, current may flow into nearby
metal objects such as a necklace, so be careful when plac-
ing battery packs (or the transceiver) in handbags, etc.
Simply carrying with or placing near metal objects such as
a necklace, etc. may cause shorting. This may damage not
only the battery pack, but also the transceiver.
RDANGER! Use and charge only specified Icom battery
packs with Icom radios or Icom chargers. Only Icom battery
packs are tested and approved for use with Icom radios or
charged with Icom chargers. Using third-party or counterfeit
battery packs or chargers may cause smoke, fire, or cause
the battery to burst.
DBattery caution
RDANGER! DO NOT hammer or otherwise impact the bat-
tery. Do not use the battery if it has been severely impacted
or dropped, or if the battery has been subjected to heavy
pressure. Battery damage may not be visible on the outside
of the case. Even if the surface of the battery does not show
cracks or any other damage, the cells inside the battery may
rupture or catch fire.
RDANGER! NEVER use or leave the battery pack in areas
with temperatures above +60˚C (+140˚F). High tempera-
ture buildup in the battery, such as could occur near fires
or stoves, inside a sun heated car, or in direct sunlight may
cause the battery to rupture or catch fire. Excessive temper-
atures may also degrade battery performance or shorten
battery life.
RDANGER! DO NOT expose the battery to rain, snow, sea-
water, or any other liquids. Do not charge or use a wet battery.
If the battery gets wet, be sure to wipe it dry before using.
RDANGER! NEVER incinerate a used battery pack since
internal battery gas may cause it to rupture, or may cause an
explosion.
RDANGER! NEVER solder the battery terminals, or NEVER
modify the battery pack. This may cause heat generation, and
the battery may burst, emit smoke or catch fire.
RDANGER! Use the battery only with the transceiver for
which it is specified. Never use a battery with any other
equipment, or for any purpose that is not specified in this in-
struction manual.
RDANGER! If fluid from inside the battery gets in your eyes,
blindness can result. Rinse your eyes with clean water, with-
out rubbing them, and see a doctor immediately.
R WARNING! Immediately stop using the battery if it emits
an abnormal odor, heats up, or is discolored or deformed. If
any of these conditions occur, contact your Icom dealer or
distributor.
Misuse of Li-ion batteries may result in the following haz-
ards: smoke, fire, or the battery may rupture. Misuse can
also cause damage to the battery or degradation of battery
performance.

10
3BATTERY CHARGING
R WARNING! Immediately wash, using clean water, any
part of the body that comes into contact with fluid from in-
side the battery.
RWARNING! NEVER put the battery in a microwave oven,
high-pressure container, or in an induction heating cooker. This
could cause a fire, overheating, or cause the battery to rupture.
CAUTION: Always use the battery within the specified tem-
perature range, –20˚C to +60˚C (–4˚F to +140˚F). Using the
battery out of its specified temperature range will reduce the
battery’s performance and battery life.
CAUTION: Shorter battery life could occur if the battery is
left fully charged, completely discharged, or in an excessive
temperature environment (above +50˚C; +122˚F) for an ex-
tended period of time. If the battery must be left unused for a
long time, it must be detached from the radio after discharg-
ing. You may use the battery until the battery icon shows
half-capacity, and then keep it safely in a cool dry place at
the following temperature range:
–20˚C to +50˚C (–4˚F to +122˚F) (up to a month)
–20˚C to +35˚C (–4˚F to +95˚F) (up to three months)
–20˚C to +20˚C (–4˚F to +68˚F) (up to a year)
DCharging caution
RDANGER! NEVER charge the battery pack in areas with
extremely high temperatures, such as near fires or stoves,
inside a sun-heated vehicle, or in direct sunlight. In such en-
vironments, the safety/protection circuit in the battery will ac-
tivate, causing the battery to stop charging.
R WARNING! DO NOT charge or leave the battery in the
battery charger beyond the specified time for charging. If the
battery is not completely charged by the specified time, stop
charging and remove the battery from the battery charger.
Continuing to charge the battery beyond the specified time
limit may cause a fire, overheating, or the battery may rup-
ture.
R WARNING! NEVER insert the transceiver, with the bat-
tery attached, into the charger if it is wet or soiled. This could
corrode the battery charger terminals or damage the char-
ger. The charger is not waterproof.
CAUTION: DO NOT charge the battery outside of the spec-
ified temperature range: BC-193/BC-197 (+10˚C to +40˚C;
+50˚F to +104˚F). Icom recommends charging the bat-
tery at +20˚C (+68˚F). The battery may heat up or rupture if
charged out of the specified temperature range. Additionally,
battery performance or battery life may be reduced.
The supplied battery pack, charger, and AC adapter dif-
fer, or no supplied depending on the version.
Prior to using the transceiver for the first time, the battery
pack must be fully charged for optimum life and operation.

11
2
3
BATTERY CHARGING
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
■Battery chargers
D Using the BC-191 to rapid charge the BP-264
The BC-191 provides rapid charging of only the BP-264 Ni-MH
battery pack. Never use it to charge any other battery pack.
Charging time: Approximately 2 hours
The following item is additionally required:
• An AC adapter (not supplied with some versions) or the OPC-515L
or CP-23L DC power cable.
DUsing the BC-192 to regular charge the BP-264
The BC-192 provides regular charging of only the BP-264
Ni-MH battery pack. Never use it to charge any other battery
pack.
Charging time (with the BC-147S): Approximately 16 hours
The following item is additionally required:
• An AC adapter (not supplied with some versions) or the OPC-515L
DC power cable.
The optional OPC-
515L (for DC power
source) can be
used instead of the
AC adapter.
Charge indicator
• Lights green while charging.
NOTE:
The charge indicator will not
go out even after a battery
pack is fully charged.
AC adapter
(A different type, or no AC
adapter is supplied, de-
pending on the version.)
Transceiver
Battery pack
Screws*
(Self tapping screw:
3.5 × at least 30 mm)
*Purchase separately.
Using screws is
recommended to
secure the charger.
Charging time period differs,
depending on the input voltage.
12 V : Approximately 36 hours
13.8 V : Approximately 21 hours
16 V : Approximately 16 hours
Tu rn OFF the power
The optional OPC-515L
(for DC power source)
or CP-23L (for 12 V
cigarette lighter socket)
can be used instead of
the AC adapter.
Charge indicator
• Lights orange : While charging
• Lights green :
Charging is completed.
AC adapter
(A different type, or no AC
adapter is supplied, de-
pending on the version.)
Transceiver
Battery pack
Screws*
(Self tapping screw:
3.5 × at least 30 mm)
*Purchase separately.
Using screws is
recommended to
secure the charger.
Tu rn OFF the power

12
3BATTERY CHARGING
D Using the BC-193 to rapid charge the BP-265
The BC-193 provides rapid charging of only the BP-265 Li-
ion battery pack. Never use it to charge any other battery
pack.
Charging time: Approximately 2.5 hours
The following item is additionally required:
• An AC adapter (not supplied with some versions) or the OPC-515L
or CP-23L DC power cable.
IMPORTANT: Battery charging caution
Ensure the tabs on the battery pack are correctly aligned
with the guide rails inside the charger.
CAUTION: When using the OPC-515L DC power cable
NEVER connect the OPC-515L to a power source using
reverse polarity. This will ruin the battery charger.
White line:
+
Black line:
–
The optional OPC-515L
(for DC power source)
or CP-23L (for 12 V
cigarette lighter socket)
can be used instead of
the AC adapter.
AC adapter
(A different type, or no AC
adapter is supplied, de-
pending on the version.)
Transceiver
Battery pack
Screws*
(Self tapping screw:
3.5 × at least 30 mm)
*Purchase separately.
Using screws is
recommended to
secure the charger.
Charge indicator
• Lights orange : While charging
• Lights green : Charging is completed.
Tu rn OFF the power
Guide rail
Tabs

13
3
3
BATTERY CHARGING
1
2
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
The BC-197 rapidly charges up to six battery packs.
Charging time for BP-264: Approximately 2 hours
Charging time for BP-265: Approximately 2.5 hours
The following additional item is required:
• An AC adapter (not supplied with some versions) or the DC
power cable (OPC-656)
There are two types of BC-197 chargers for the IC-U80 or IC-
U80E; one is for Ni-MH batteries, and the other is for Li-ion
batteries.
Before you purchase a BC-197, check the type of battery you
are using, and then be sure to choose the suitable charger.
BC-197 Charger Type Chargeable Battery
With AD-120*1charger adapters BP-264 Ni-MH battery
With AD-121*1charger adapters BP-265 Li-ion battery
*1The type of the charger adapter, AD-120 or AD-121 is printed on
the inside bottom of the charger adapter, and the type of battery it
holds is printed on the top right corner of the adapter.
TransceiverBattery
pack
Charger adapters*2are
installed in each slot.
Tu rn OFF the power
The shape of charger adapter depends
on the version of the BC-197.
*2
(An AC adapter is
not supplied with
some versions.)
AC adapter
(Connect to a DC power supply;
12 to 16 V/at least 7 A)
Red line : +Black line : _
DC power cable (OPC-656)
DUsing the BC-197 to rapid charge the BP-264 or BP-265

14
■Battery case (BP-263)
When using the BP-263 battery case, install 6 ×AA (LR6)
size alkaline batteries, as described below.
qRemove the battery case if it is attached. (p. 2)
wInstall 6 × AA (LR6) size alkaline batteries.
• Install only alkaline batteries.
• Be sure to observe the correct polarity.
eAttach the battery case. (p. 2)
CAUTION:
• When installing batteries, make sure they are all the
same brand, type and capacity. Also, do not mix new
and old batteries together.
• Keep the battery terminals clean. It’s a good idea to
clean the battery terminals once a week.
• Never incinerate used battery cells since the internal
battery gas may cause them to rupture.
• Never expose a detached battery case to water. If the bat-
tery case gets wet, be sure to wipe it dry before using it.
• Never use batteries whose insulated covering is damaged.
NOTE: When the BP-263 battery case is attached, the
battery protection function must be turned OFF in the Ini-
tial Set mode (p. 49).
■Battery information
DBattery life
Even when the transceiver power is OFF, a small current still
flows in the transceiver. Remove the battery pack or case
when it won’t be used for a long time. Otherwise, the battery
pack or the batteries in the case will become exhausted.
DBattery indication
The battery icons, “ ,” appears when a battery pack or
case is attached to the transceiver.
3BATTERY CHARGING
Battery pack/case Voltage Capacity Battery life*1
BP-263 Battery case for
AA (LR6) × 6 alkaline —*2
BP-264 7.2 V 1400 mAh 14.5 hrs.
BP-265 7.4 V 1900 mAh (min.)
2000 mAh (typ.) 17.5 hrs.
*1 When the power save function is set to “P–S.At,” and the operating
time is calculated under the following conditions;
TX : RX : standby = 5 : 5 : 90
*2The average operating life depends on the alkaline cells used.
Icon Battery condition
The battery has ample capacity.
The battery is nearing exhaustion.
Charging the battery pack, or replacing the batteries in
the case is necessary.
Be careful! The negative ter-
minals of the battery case pro-
trude from the body, so pay at-
tention not to injure your fingers
when inserting the batteries.