ICON Health & Fitness PRO-FORM LE TOUR DE FRANCE User manual

USER’S MANUAL
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
Model No. PFEX01915.0
Serial No.
Write the serial number in the space
above for reference.
www.proform.com
Serial Number
Decal
To register your product and
activate your warranty today,
go to www.proformservice.com/
registration.
For service at any time, go to
www.proformservice.com.
Or call 1-877-660-1168
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–12 p.m. MT
Please do not contact the store.
ACTIVATE YOUR
WARRANTY
CUSTOMER CARE

2
This drawing shows the location(s) of the
warning decal(s). If a decal is missing
or illegible, see the front cover of this
manual and request a free replacement
decal. Apply the decal in the location
shown. Note: The decal(s) may not be
shown at actual size.
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
HOW TO USE THE TRAINING BIKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
MAINTENANCE AND TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
ORDERING REPLACEMENT PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
WARNING DECAL PLACEMENT
TABLE OF CONTENTS
PROFORM is a registered trademark of ICON Health & Fitness, Inc. IFIT is a registered trademark of ICON
Health & Fitness, Inc. LE TOUR DE FRANCE is a registered trademark of Société du Tour de France. Google
Maps is a trademarks of Google Inc. The BLUETOOTH®word mark and logos are registered trademarks of
Bluetooth SIG, Inc. and are used under license. Wi-Fi is a registered trademark of Wi-Fi Alliance. WPA and WPA2
are trademarks of Wi-Fi Alliance.

3
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read all
important precautions and instructions in this manual and all warnings on your training bike before
using your training bike. ICON assumes no responsibility for personal injury or property damage
sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
1. It is the responsibility of the owner to ensure
that all users of the training bike are ade-
quately informed of all precautions.
2. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or per-
sons with pre-existing health problems.
3. Use the training bike only as described in
this manual.
4. The training bike is intended for home use
only. Do not use the training bike in a com-
mercial, rental, or institutional setting.
5. Keep the training bike indoors, away from
moisture and dust. Do not put the training
bike in a garage or covered patio, or near
water.
6. Place the training bike on a level surface with
at least 2 ft. (0.6 m) of clearance around the
training bike. To protect the floor or carpet
from damage, place a mat under the training
bike.
7. Inspect and properly tighten all parts each
time the training bike is used. Replace any
worn parts immediately.
8. Keep children under age 12 and pets away
from the training bike at all times.
9. When connecting the power cord, plug the
power cord into a grounded circuit.
10. Do not modify the power cord or use an
adapter to connect the power cord to an
improper receptacle. Keep the power cord
away from heated surfaces. Do not use an
extension cord.
11. Do not operate the training bike if the power
cord or plug is damaged, or if the training
bike is not working properly.
12. DANGER: Always unplug the power
cord and press the power switch to the off
position when the training bike is not in
use and before cleaning the training bike.
Servicing other than the procedures in this
manual should be performed by an autho-
rized service representative only.
13. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the training bike. Always wear
athletic shoes for foot protection.
14. The training bike should not be used by
persons weighing more than 350 lbs.
(159 kg).
15. Be careful when mounting and dismounting
the training bike.
16. Always keep your back straight while using
the training bike; do not arch your back.
17. Over exercising may result in serious injury
or death. If you feel faint, if you become short
of breath, or if you experience pain while
exercising, stop immediately and cool down.

4

5
all
STANDARD SERVICE PLANS

6
Congratulations for selecting the revolutionary
PROFORM®LE TOUR DE FRANCE®training bike.
The LE TOUR DE FRANCE training bike is unlike any
ordinary exercise bike. With full adjustability, a Wi-Fi®
cycling console, an incline system that simulates actual
road terrain, and an array of other innovative features,
the LE TOUR DE FRANCE training bike is designed to
let you enjoy the outdoor cycling experience indoors.
For your benefit, read this manual carefully before
you use the training bike. If you have questions after
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Saddle
Shifter
Saddle Carriage
Adjustment Handle
Adjustment Handle
Handlebar
Tray
Adjustment Handle
Wheel
Pedal/Strap
Console
Leveling Foot
Power Switch
Length: 5 ft. 4 in. (163 cm)
Width: 2 ft. 1 in. (64 cm)
BEFORE YOU BEGIN

7
M6 x 16mm
Screw (110)–4
M4 x 10mm
Screw (116)–2
M10 x 58mm
Screw (74)–4
M4 Washer
(54)–1
M4 x 14mm
Screw (117)–1
M4 x 12mm
Screw (111)–4
PART IDENTIFICATION CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the
key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it
has been preassembled. Extra parts may be included.

8
2
22
74
Shipping
Insert
1
2. Remove and discard the indicated shipping
insert. If there are shipping screws in the
Front Stabilizer (22), remove and discard
them.
Attach the Front Stabilizer (22) to the Base (1)
with two M10 x 58mm Screws (74).
ASSEMBLY
• To hire an authorized service technician to
assemble the training bike, call 1-800-445-2480.
• Assembly requires two persons.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you finish all assembly steps.
• Left parts are marked “L” or “Left” and right parts
are marked “R” or “Right.”
• To identify small parts, see page 7.
• In addition to the included tool(s), assembly
requires the following tools:
one Phillips screwdriver
Assembly may be easier if you have your own set
of wrenches. To avoid damaging parts, do not use
power tools.
1. Go to www.proformservice.com/registration
on your computer and register your product.
•activates your warranty
•saves you time if you ever need to contact
Customer Care
•allows us to notify you of upgrades and offers
Note: If you do not have Internet access, call
Customer Care (see the front cover of this
manual) and register your product.
1

9
2
3
Indicators
47
3
3. If there are shipping screws in the Rear
Stabilizer (23), remove and discard them.
Attach the Rear Stabilizer (23) to the Base (1)
with two M10 x 58mm Screws (74).
74
23
1
4. Using a plastic bag to keep your fingers clean,
apply some of the included grease to the sides
of the channel on the top of the Saddle Post (3).
Next, orient the Saddle Post (3) so that the
height indicators are on the side shown.
LoosentheindicatedAdjustmentHandle(47),
and insert the Saddle Post (3) into the Frame (2).
Move the Saddle Post upward or downward
to the desired position, and then tighten the
Adjustment Handle. When you are finished
tightening the Adjustment Handle, make sure
that the end of the Adjustment Handle is
pointing upward.
Note:TheAdjustmentHandle(47)functions
like a ratchet. Turn the Adjustment Handle in
the desired direction, pull it outward, turn it in
the opposite direction, push it inward, and then
turn it in the desired direction again. Repeat this
process as many times as necessary.
4Grease

10
5
5. Note: You can attach your own saddle to the
Saddle Carriage (4) if desired. Loosen the
attachment hardware (not shown) beneath the
Saddle (5), and remove the Saddle. Then, attach
your own saddle and retighten the attachment
hardware.
Orient the Saddle Carriage (4) as shown.
LoosentheAdjustmentHandle(47),andslide
the Saddle Carriage (4) into the Saddle Post (3).
Slide the Saddle Carriage to the desired posi-
tion, and tighten the Adjustment Handle.
Then,attachanM4Washer(54)andthe
Carriage Cover (91) to the Saddle Carriage (4)
with an M4 x 14mm Screw (117).
3
4
5
117 47
54
91
6
6
2
68
105
47
Wire
Tie
Wire Tie
Access
Hole
Pull Here
6. See step 8. If the Handlebar Clamp (28) and
four M6 x 16mm Screws (110) are preattached
to the Handlebar Carriage (105), remove them
and set them aside until step 8.
Have a second person hold the Handlebar Post
(6) near the Frame (2).
LocatethelongwiretieintheHandlebarPost
(6). Tie the lower end of the long wire tie to the
Main Wire (68). Next, locate the same wire tie in
the access hole in the Handlebar Carriage (105).
Pull the wire tie upward until the end of the Main
Wire is in the access hole.
See the inset drawing. Next, pull the upper end
of the long wire tie until the Main Wire (68) is
routed through the Handlebar Carriage (105) as
shown. Then, untie and discard the long wire tie.
Tip:AvoidpinchingtheMainWire(68).
Loosen the indicated Adjustment Handle (47),
and insert the Handlebar Post (6) into the
Frame (2). Move the Handlebar Post upward or
downward to the desired position, and tighten
the Adjustment Handle.
Avoid pinching the
Main Wire (68)
105
68
Wire
Tie

11
105
107
9
9
68
9. Have a second person hold the Console (9) near
the Handlebar Carriage (105).
ConnecttheconsolewirestotheMainWire(68)
and to the Extension Wires (107, 108); make
sure to connect the console wire that has an
“L” tag to the Extension Wire that has an “L”
tag, and connect the console wire that has an
“R” tag to the Extension Wire that has an “R”
tag.
InserttheexcesswireintotheConsole(9).
7. Have a second person hold the Handlebar (7)
near the Handlebar Carriage (105).
Locateoneoftheremainingwiretiesinthe
Handlebar Carriage (105). Tie the indicated end
of the wire tie to the Right Extension Wire (107).
Then, pull the other end of the wire tie until
the Right Extension Wire is routed through the
Handlebar Carriage. Then, untie and discard the
wire tie.
Route the Left Extension Wire (108) through
the Handlebar Carriage (105) in the same
way.
8. Tip: Avoid pinching the wires. Hold the
Handlebar (7) on the Handlebar Carriage (105),
and rotate the Handlebar to the desired angle;
make sure that the Handlebar is centered on
the Handlebar Carriage.
AttachtheHandlebar(7)withtheHandlebar
Clamp (28) and four M6 x 16mm Screws (110);
start all four Screws, and then tighten them.
7
8
7
7
110
28
105
105
108
107
Wire Tie
Avoid pinching
the wires
108

12
10
111
105
9
10. Tip: Avoid pinching the wires. Attach the
Console (9) to the Handlebar Carriage (105) with
four M4 x 12mm Screws (111); start all four
Screws, and then tighten them.
Avoid pinching
the wires
11. Attach the Tray (8) to the Frame (2) with two
M4 x 10mm Screws (116). 11
8
2
116
13. After the training bike is assembled, inspect it to make sure that it is assembled correctly and that it
functions properly. Make sure that all parts are properly tightened before you use the training bike.
Note: Extra parts may be included. Place a mat beneath the training bike to protect the floor.
12. Note: You can attach your own pedals if
desired.
IdentifytheRightPedal(62).
Usingtheincludedflatwrenchtool,firmly
tighten the Right Pedal (62) clockwise into the
Right Crank Arm (64).
Firmly tighten the Left Pedal (not shown)
counterclockwise into the Left Crank Arm
(not shown). IMPORTANT: You must turn the
Left Pedal counterclockwise to attach it.
12
62
64

13
HOW TO PLUG IN THE POWER CORD
This product must be grounded. If it should mal-
function or break down, grounding provides a path of
least resistance for electric current to reduce the risk
of electric shock. The power cord has a plug with a
grounding pin.
Plug the
power cord
into an
appropriate
outlet that
is properly
installed and
grounded in
accordance
with all local
codes and
ordinances. The outlet must be on a nominal 120-volt
circuit.
A temporary
adapter may
be used to
connect the
power cord
to a 2-pole
receptacle
as shown
at the right
if a properly
grounded
outlet is not
available.
The lug or wire extending from the adapter must
be connected with a metal screw to a permanent
ground such as a properly grounded outlet box cover.
Some 2-pole receptacle outlet box covers are not
grounded. Before using an adapter, contact a quali-
fied electrician to determine whether the outlet
box cover is grounded before using an adapter.
The temporary adapter should be used only until
a properly grounded outlet can be installed by a
qualified electrician.
HOW TO USE THE TRAINING BIKE
DANGER: Improper connection of
the power cord increases the risk of electric
shock. Do not modify the plug; if it will not fit
an outlet, have a proper outlet installed by a
qualified electrician. If you are unsure whether
the product is properly grounded, contact a
qualified electrician.
Grounded Outlet
2-pole Receptacle
Grounding Pin
Adapter
Lug
Metal Screw

14
FEATURES OF THE TRAINING BIKE
Measuring Watts
Each training bike is individually calibrated to measure
your power output and allow you to monitor your watts
and RPMs directly on the console.
By monitoring your watts and RPMs, you can see how
hard you are training and make sure that you are chal-
lenging yourself and improving.
The Incline System
The training bike can incline and decline up to 20 per-
cent to realistically simulate outdoor terrain. When you
create maps of your actual training routes on iFit.com
(see the console instructions beginning on page 16
for more information), the training bike will automati-
cally incline and decline to match the terrain of your
training routes.
The Handlebar Shifters
The training bike allows you to shift gears just like
you do on your road bike. The right and left handlebar
shifters simulate front and rear derailleurs that you can
configure to match the gearing setup of your road bike
(see the console instructions beginning on page 16
for more information).
Pedaling Form Features
The training bike has multiple features to help you
develop correct pedaling form:
Freewheel—The training bike has a freewheel that
simulates a road bike rather than a fixed-drive spin
bike. This discourages you from letting your feet coast
through the top and bottom of your pedal stroke.
Flywheel—The flywheel on the training bike has the
correct inertia to allow you to pedal smoothly while
encouraging you to use good pedaling form.
HOW TO ADJUST THE GEOMETRY OF THE
TRAINING BIKE
The training bike can be adjusted to match the geom-
etry of your road bike to promote correct form and to
ensure proper training of the muscles. Note: Make
adjustments in small increments, and then pedal
the training bike to test the adjustments.
How to Adjust the Angle of the Saddle
You can adjust the angle of the saddle to the posi-
tion that is most comfortable. You can also adjust the
saddle forward or backward for increased comfort or to
adjust the distance to the handlebar.
To adjust the
saddle, first loosen
the attachment
hardware beneath
the saddle a few
turns. Next, tilt the
saddle upward or
downward or slide
the saddle forward
or backward, Then,
retighten the attach-
ment hardware.
Note: You can remove the saddle and attach your
own saddle if desired.
How to Adjust the Saddle Carriage
To ad j ust t h e pos i -
tion of the saddle
carriage, loosen the
adjustment handle,
move the saddle
carriage forward or
backward, and then
retighten the adjust-
ment handle.
Note: The adjustment handle functions like a ratchet.
Turn the adjustment handle in the desired direction,
pull it outward, turn it in the opposite direction, push it
inward, and then turn it in the desired direction again.
Repeat this process as many times as necessary.
Hardware
Saddle
Carriage
Handle

15
How to Adjust the Saddle Post
For effective train-
ing, the saddle
should be at the
proper height. As
you pedal, there
should be a slight
bend in your knees
when the pedals are
in the lowest posi-
tion. To adjust the
height of the saddle
post, loosen the adjustment handle, move the saddle
post upward or downward, and then retighten the
adjustment handle. When you are finished tighten-
ing the Adjustment Handle, make sure that the end
of the Adjustment Handle is pointing upward.
How to Adjust the Rotation of the Handlebar
To rotate the
handlebar to match
the position of the
handlebar on your
road bike, loosen
the indicated
screws, rotate the
handlebar, and
then retighten the
screws.
How to Adjust the Handlebar Post
To ad j ust t h e hei g ht
of the handlebar
post, loosen the
adjustment handle,
move the handle-
bar post upward
or downward, and
then retighten the
adjustment handle.
How to Adjust the Handlebar Carriage
To adjust the
position of the
handlebar carriage
to match your road
bike, loosen the
indicated screws,
move the handlebar
carriage forward
or backward, and
then retighten the
screws.
HOW TO LEVEL THE TRAINING BIKE
If the training bike
rocks slightly on
your floor during
use, turn one or
both of the level-
ing feet on the rear
stabilizer until the
rocking motion is
eliminated.
HOW TO USE THE PEDALS
To use the pedals, insert your shoes into the toe
cages, and pull the ends of the toe straps. To adjust
the toe straps, press and hold the tabs on the buckles,
adjust the toe straps to the desired position, and then
release the tabs.
Note: You can attach your own pedals to the training
bike if desired.
THE OPTIONAL TABLET HOLDER
The optional
tablet holder will
hold your tablet
securely in place
and enable you
to use your tablet
while you exercise.
The optional tablet
holder is designed
for use with most
full-size tablets. To purchase a tablet holder, please
see the front cover of this manual.
Handle
Saddle
Post
Screws
Handle
Handlebar
Post
Handlebar
Carriage
Screws
Leveling
Foot

16
CONSOLE DIAGRAM
MAKE YOUR FITNESS GOALS A REALITY WITH
IFIT.COM
With your new iFit-compatible fitness equipment, you
can use an array of features on iFit.com to make your
fitness goals a reality:
Train anywhere in the world with
customizable Google Maps™.
Download training workouts designed to
help you reach your personal goals.
Measure your progress by competing
against other users in the iFit community.
Upload your workout results to the iFit cloud
and track your accomplishments.
Set calorie, time, distance, or watts goals
for your workouts.
Choose and download sets of weight-loss
workouts.
Go to iFit.com to learn more.
Watch high-definition videos with simulated
workouts.

17
FEATURES OF THE CONSOLE
The advanced console offers an array of features
designed to make your workouts more effective and
enjoyable.
When you use the manual mode of the console, you
can change the incline (resistance) of the training bike
and change gears with the touch of a button.
While you exercise, the console will display continu-
ous exercise feedback, including watts and pedaling
cadence feedback.
During your workout, you can do intervals at any time
to measure your performance over short periods of
time. The console will record and display your results
for each interval.
You can also measure your heart rate using an optional
heart rate monitor.
In addition, the console offers a selection of Le Tour de
France workouts. Each workout automatically changes
the incline (resistance) of the training bike to match the
real terrain of the Le Tour de France bicycle race and
allows you to change gears to maintain your desired
pedaling cadence.
The console also features new iFit technology that
enables the console to communicate with your wireless
network. With iFit technology, you can download per-
sonalized workouts, create your own workouts, track
your workout results, and access many other features.
See www.iFit.com for complete information.
You can even connect your MP3 player or CD player
to the console sound system and listen to your favorite
music or audio books while you exercise.
To turn on the power, see this page. To learn how to
use the touch screen, see page 18. To set up the
console, see page 18.
HOW TO TURN ON THE POWER
IMPORTANT: If the training bike has been exposed
to cold temperatures, allow it to warm to room tem-
perature before you turn on the power. If you do
not do this, you may damage the console displays
or other electrical components.
Plug in the power cord (see
HOW TO PLUG IN THE
POWER CORD on page
13). Next, locate the
power switch on the frame
near the power cord. Press
the power switch to the
reset position.
The display will then turn on and the console will be
ready for use.
Note: When you turn on the power for the first time,
the incline system may calibrate automatically.
The training bike will move upward and downward as
it calibrates. When the training bike stops moving, the
incline system is calibrated.
IMPORTANT: If the incline system does not cali-
brate automatically, see step 4 on page 26 and
manually calibrate the incline system.
IMPORTANT: The console features a display demo
mode, designed to be used if the training bike is
displayed in a store. If the demo mode is turned on,
the console will not turn off and the display will not
be reset when you finish exercising. To turn off the
demo mode, see step 8 on page 24.
Reset
Position

18
HOW TO USE THE TOUCH SCREEN
The console features a tablet with a full-color touch
screen. The following information will help you become
familiar with the tablet’s advanced technology:
• The console functions similarly to other tablets. You
can slide or flick your finger against the screen to
move certain images on the screen, such as the
displays in a workout. However, you cannot zoom in
and out by sliding your fingers on the screen.
• To type information into a text box, first touch the text
box to view the keyboard. To use numbers or other
characters on the keyboard, touch the ?123 button.
To vi e w mor e c har a ct e r s, t o u ch t h e A lt bu t ton . Tou ch
the Alt button again to return to the number key-
board. To return to the letter keyboard, touch the
ABC button. To use a capital character, touch the
button with an upward-facing arrow. To use multiple
capital characters, touch the arrow button again. To
return to the lowercase keyboard, touch the arrow
button a third time. To clear the last character, touch
the button with a backward-facing arrow and an X.
• Use these buttons
on the console to
navigate the tablet.
Press the home but-
ton to return to the
main menu. Press the
center button to access the settings menu (see page
24). Press the back button to return to the previ-
ous screen.
HOW TO SET UP THE CONSOLE
Before using the training bike for the first time, follow
the steps below to set up the console.
1. Connect to a wireless network.
Note: To access the Internet, download iFit work-
outs, and use some other features of the console,
the console must be connected to a wireless
network. See HOW TO USE THE WIRELESS
NETWORK MODE on page 27 to connect the
console to your wireless network.
2. Check for firmware updates.
First, see step 1 on page 24 and step 2 on page
26 and select the maintenance mode. Then,
see step 3 on page 26 and check for firmware
updates.
3. Calibrate the incline system.
First, see step 1 on page 24 and step 2 on page
26 and select the maintenance mode. Then,
see step 4 on page 26 and calibrate the incline
system of the training bike.
4. Create an iFit account.
On your computer, smartphone, tablet, or other
Internet-capable device, open an Internet browser
and go to www.iFit.com. Follow the prompts on the
website to sign up for your iFit membership. If you
have an activation code, select the code activation
option.
The console is now ready for you to begin training. The
following pages explain the various workouts and other
features that the console offers.
To use the manual mode, see page 19. To use a
Le Tour de France workout, see page 21. To use
a set-a-goal workout, see page 22. To use an iFit
workout, see page 23.
To use the equipment settings mode, see
page 24. To use the maintenance mode, see
page 26. To use the wireless network mode,
see page 27. To use the sound system, see page
28. To use the Internet browser, see page 28.
Note: If there is a sheet of plastic on the display,
remove the plastic.
The console can display speed and distance in either
miles or kilometers. To find which unit of measurement
is selected, see step 15 on page 25. For simplicity,
all instructions in this section refer to miles.

19
HOW TO USE THE MANUAL MODE
1. Touch the screen or begin pedaling to activate
the console.
See HOW TO TURN ON THE POWER on
page 17.
2. Select the main menu.
When you turn on the console, the main menu will
appear on the screen after the console boots up.
Touch the home button at the bottom of the screen
to return to the main menu at any time.
TouchtheStartbuttontostartamanualworkout.
3. Change the incline (resistance) of the training
bike as desired.
As you pedal, change the incline (resistance) of the
training bike by pressing the Grade increase and
decrease buttons on the console.
You can also change the incline of the training
bike by pressing the shifter buttons. To increase
the incline, press the front and rear buttons on the
right shifter simultaneously; to decrease the incline,
press the front and rear buttons on the left shifter
simultaneously.
Note: After you press a button, it will take a
moment for the training bike to reach the selected
incline level. You will hear the incline motor
while the incline is changing. This is normal.
CAUTION: The training bike can move through
a broad range of incline levels. Hold the handle-
bars and be prepared for the training bike to
move when you change the incline.
4. Change gears as desired.
You can set up the training bike to simulate
your road bike. To select the gearing option(s)
for the training bike, see step 7 on page 24.
Note: The training bike simulates gears; there are
no actual gears.
Change gears by pressing the buttons on the
shifters. Note: After you press a button, it will take
a moment for the training bike to change to the
selected gear. To avoid damaging the shift-
ers, do not pull on the shifters or squeeze the
shifters.
Press the buttons on the left shifter to change the
front gear; press the buttons on the right shifter to
change the rear gear.
On the left shifter, press the front button to increase
the resistance; press the rear button to decrease
the resistance.
On the right shifter, press the front button to
decrease the resistance; press the rear button to
increase the resistance.
The numbers of the currently selected front and
rear gears will appear in the display on the screen.
5. Follow your progress.
The console offers several display modes. The
display mode that you select will determine which
workout information is shown.
To se l ect t h e des i re d d i sp l a y mo d e , si m ply f l ick o r
slide the screen. You can also view additional work-
out information by touching the red boxes on the
screen.
If desired, adjust
the volume level by
pressing the vol-
ume increase and
decrease buttons on
the console.
To pause the workout, stop pedaling or touch either
the back button or the home button at the bottom
of the screen. To continue the workout, touch the
Resume button. To end the workout session, touch
the End Workout button.
When you touch the End Workout button, a work-
out summary will appear on the screen. After you
view the workout summary, touch the Finish button
to return to the main menu. You may also be able
to either save or publish your results using one of
the options on the screen.

20
6. Do intervals if desired.
During a workout, you can use the interval screen
to measure your performance for short periods of
time. To select the interval screen, simply flick or
slide the screen.
To be g in an i n ter v al , t o uc h t h e St a r t bu t ton . To en d
the current interval, touch the Lap button. You can
add as many intervals as desired to your workout.
The console will record data for each interval that
you can view at any time during your workout. The
interval screen will show a list of the recorded inter-
vals. Scroll the screen to view data for the desired
interval.
7. Wear a heart rate monitor and measure your
heart rate if desired.
You can wear an optional heart rate monitor
to measure your heart rate. For more informa-
tion about the optional heart rate monitor, see
page 28. Note: The console is compatible with
BLUETOOTH®Smart heart rate monitors.
When your heart beat is detected, your heart rate
will be shown in the display on the screen.
8. When you are finished exercising, unplug the
power cord.
When you are finished exercising, press the power
switch to the off position and unplug the power
cord. IMPORTANT: If you do not do this, the
electrical components of the training bike may
wear prematurely.