ICON Health & Fitness WESLO Momentum G 3.2 User manual

CAUTION
Read all precautions and
instructions in this manual before
using this equipment. Keep this
manual for future reference.
Model No. WLEL32115.0
Serial No.
Write the serial number in the space
above for reference.
USER’S MANUAL
weslo.com
Serial
Number
Decal
To register your product and
activate your warranty today,
go to my.weslo.com.
For service at any time, go to
wesloservice.com.
Or call 1-866-699-3756
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–12 p.m. MT
Please do not contact the store.
ACTIVATE YOUR
WARRANTY
CUSTOMER CARE

2
WARNING DECAL PLACEMENT
166909 218557
218556
!
250085
• Not for therapeutic
use.
• Nicht für thera-
peutisch Gebrauch.
151249
259345
258865
258868 258869 258870 258871 258872
255569 258724 203572
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS..................................................................3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
HOW TO USE THE HYBRID TRAINER .........................................................16
FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
MAINTENANCE AND TROUBLESHOOTING ....................................................21
EXERCISE GUIDELINES ....................................................................22
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
ORDERING REPLACEMENT PARTS .................................................. Back Cover
LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
This drawing shows the location(s) of the warning
decal(s). If a decal is missing or illegible, see
the front cover of this manual and request a
free replacement decal. Apply the decal in the
location shown. Note: The decal(s) may not be
shown at actual size.
WESLO is a registered trademark of ICON Health & Fitness, Inc.

3
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your hybrid trainer before using your hybrid trainer.
ICON assumes no responsibility for personal injury or property damage sustained by or through the
use of this product.
1. It is the responsibility of the owner to ensure
that all users of the hybrid trainer are ade-
quately informed of all precautions.
2. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or per-
sons with pre-existing health problems.
3. The hybrid trainer is not intended for use by
persons with reduced physical, sensory, or
mental capabilities or lack of experience and
knowledge, unless they are given supervi-
sion or instruction about use of the hybrid
trainer by someone responsible for their
safety.
4. Use the hybrid trainer only as described in
this manual.
5. The hybrid trainer is intended for home use
only. Do not use the hybrid trainer in a com-
mercial, rental, or institutional setting.
6. Keep the hybrid trainer indoors, away from
moisture and dust. Do not put the hybrid
trainer in a garage or covered patio or near
water.
7. Place the hybrid trainer on a level surface,
with at least 3 ft. (0.9 m) of clearance in the
front and rear of the hybrid trainer and 2 ft.
(0.6 m) on each side. To protect the floor or
carpet from damage, place a mat under the
hybrid trainer.
8. Inspect and properly tighten all parts each
time the hybrid trainer is used. Replace any
worn parts immediately.
9. Keep children under age 13 and pets away
from the hybrid trainer at all times.
10. The hybrid trainer should not be used
by persons weighing more than 250 lbs.
(113 kg).
11. Wear appropriate clothes while exercis-
ing; do not wear loose clothes that could
become caught on the hybrid trainer. Always
wear athletic shoes for foot protection while
exercising.
12. Hold the handlebars or the upper body arms
when mounting, dismounting, or using the
hybrid trainer.
13. Make sure that the pedal knobs are fully
tightened each time you use the hybrid
trainer.
14. The heart rate monitor is not a medical
device. Various factors may affect the accu-
racy of heart rate readings. The heart rate
monitor is intended only as an exercise aid
in determining heart rate trends in general.
15. The hybrid trainer does not have a freewheel;
the pedals will continue to move until the
flywheel stops. Reduce your pedaling speed
in a controlled way.
16. Keep your back straight while using the
hybrid trainer; do not arch your back.
17. Over exercising may result in serious injury
or death. If you feel faint, if you become short
of breath, or if you experience pain while
exercising, stop immediately and cool down.
IMPORTANT PRECAUTIONS

4
all
STANDARD SERVICE PLANS

5
BEFORE YOU BEGIN
Thank you for selecting the revolutionary WESLO®
MOMENTUM G 3.2 hybrid trainer. The MOMENTUM
G 3.2 hybrid trainer provides an impressive selection
of features designed to make your workouts at home
more effective and enjoyable.
For your benefit, read this manual carefully before
you use the hybrid trainer. If you have questions after
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Handlebar
Seat
Seat Knob
Seat Post Knob
Leveling Cap
Upper Body Arm
Resistance Knob
Console
Pedal
Heart Rate Monitor
Length: 4 ft. 3 in. (130 cm)
Width: 2 ft. 1 in. (64 cm)

6
M8 Large
Washer (72)–2
M8 Plastic
Washer (27)–2
M8 Split
Washer (63)–13
M12 Split
Washer (74)–2
M8 Washer
(55)–14
Wave Washer
(73)–2
M8 Locknut
(53)–2
M8 Acorn Nut
(58)–6
M10 Plastic
Washer (62)–4
M10 Washer
(92)–8
M10 x 70mm Bolt (60)–2
M10 x 45mm Bolt (91)–4
M10 Locknut
(93)–6
M8 x 20mm
Screw (54)–3
M8 Curved
Washer (101)–2
M8 x 65mm Carriage Bolt (51)–2
M8 x 20mm Hex
Screw (57)–2
M4 x 12mm
Screw (66)–6
M8 x 40mm Bolt (56)–4
M8 x 60mm
Bolt (90)–2
M8 x 35mm Screw (86)–2
Right Crank
Locknut (36)–1
Left Crank
Locknut (37)–1
M8 x 65mm Bolt (100)–2
PART IDENTIFICATION CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the
key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it
has been preassembled. Extra parts may be included.

7
• To hire an authorized service technician to
assemble the hybrid trainer, call 1-800-445-2480.
• Assembly requires two persons.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you nish assembly.
• Left parts are marked “L” or “Left” and right parts
are marked “R” or “Right.”
• To identify small parts, see page 6.
• In addition to the included tool(s), assembly
requires the following tools:
one Phillips screwdriver
one adjustable wrench
one pair of pliers
one rubber mallet
Assembly may be easier if you have a set of
wrenches. To avoid damaging parts, do not use
power tools.
ASSEMBLY
1
2. Identify the Rear Stabilizer (28), which has a
Leveling Cap (33) on each end.
While a second person lifts the rear of the Frame
(1), attach the Rear Stabilizer (28) to the Frame
with two M8 x 65mm Bolts (100); start both
Bolts, and then tighten them.
2
1
33
33
28
100
1. Go to my.weslo.com on your computer and
register your product.
• documents your ownership
• activates your warranty
• ensures priority customer support if assistance
is ever needed
Note: If you do not have internet access, call
Customer Care (see the front cover of this
manual) and register your product.

8
3. While a second person lifts the front of the
Frame (1), attach the Front Stabilizer (10) to
the Frame with two M8 x 65mm Carriage Bolts
(51), two M8 Curved Washers (101), two M8
Split Washers (63), and two M8 Acorn Nuts (58);
insert both Carriage Bolts, and then tighten
the Acorn Nuts.
3
110
101
63
58
101
63
58
51
4. While a second person holds the Upright (2)
near the Frame (1), connect the Upright Wire
(31) to the Reed Switch Wire (47).
Next, connect the Resistance Cable (25) to the
Lower Cable (42) in the following way:
See inset drawing A. Pull upward on the metal
bracket on the Lower Cable (42), and insert the
tip of the Resistance Cable (25) into the wire clip
inside the metal bracket.
See inset drawing B. Firmly pull the Resistance
Cable (25) and slide it into the metal bracket on
the Lower Cable (42).
See inset drawing C. Using pliers, squeeze
together the prongs on the upper end of the
metal bracket.
4
2
1
31
47 25
25
42
42
A
B
C
42
25

9
5. Tip: Avoid pinching the wires and cables
during this step.
Slide the Upright (2) onto the Frame (1).
Attach the Upright (2) with three M8 x 20mm
Screws (54), three M8 Split Washers (63), and
three M8 Washers (55). Do not tighten the
Screws yet.
See the inset drawing. Attach the Upright
(2) with two M8 x 60mm Bolts (90), four M8
Washers (55), and two M8 Locknuts (53). Do
not tighten the Locknuts yet.
5
1
2
54
63
55
55
55
63
63
54
54
Avoid pinching the
wires and cables
1
2
55
53
53
55
90
90

10
7. Identify the Right Upper Body Arm (6) and orient
it as shown.
Next, orient an Upper Body Leg (64) so that the
hexagonal holes (B) are on the side shown.
Insert the Right Upper Body Arm (6) into the
Upper Body Leg (64). Attach the Right Upper
Body Arm with two M8 x 40mm Bolts (56), two
M8 Washers (55), two M8 Split Washers (63),
and two M8 Acorn Nuts (58). Make sure that the
heads of the Bolts are inside the hexagonal
holes (B). Start both Bolts, and then tighten
them.
Attach the Left Upper Body Arm (5) to the
other Upper Body Leg (64) in the same way.
7
56 55 63
58
64
6
5
64
B
6. Have a second person hold the Handlebar (52)
near the Upright (2).
See the inset drawing. Insert the Pulse Wires
(A) through the Grommet (99), into the left side
of the Upright (2), and out of the top of the
Upright. Then, press the Grommet into the left
side of the Upright.
Tip: Avoid pinching the Pulse Wires (A).
Attach the Handlebar (52) to the Upright (2)
with two M8 x 35mm Screws (86), two M8 Split
Washers (63), and two M8 Washers (55); start
both Screws, and then tighten them.
Then, press the Handlebar Cover (88) onto the
Handlebar (52).
6
52
A
2
88
86 63 55
Avoid
pinching
the Pulse
Wires (A)
99
A2

11
8. Finger tighten an M8 x 20mm Hex Screw (57)
with an M8 Split Washer (63), an M8 Large
Washer (72), and an M8 Plastic Washer (27) into
one end of the Upright Axle (26).
Using a plastic bag to keep your hands clean,
apply a generous amount of the included
grease to the Upright Axle (26) and to two Wave
Washers (73).
Next, orient the Left Upper Body Arm (5)
assembly as shown. Make sure that the
wide side (C) of the tube is in the indicated
location.
Insert the Upright Axle (26) through the Left
Upper Body Arm (5) from the direction shown.
Then, slide a Wave Washer (73) onto the Upright
Axle (26).
5
73
26
27
63
57
72
Grease
C
8
9. Tip: Avoid pinching the Upright Wire (31).
Gently pull upward on the Upright Wire, and then
insert the Upright Axle (26) through the left side
of the Upright (2) as shown.
Next, slide a Wave Washer (73) onto the Upright
Axle (26).
Orient the Right Upper Body Arm (6) assembly
as shown. Make sure that the wide side (C) of
the tube is in the indicated location.
Slide the Right Upper Body Arm (6) onto the
right side of the Upright Axle (26).
6
2
5
73
31
26
9
C
Avoid
pinching
the Upright
Wire (31)

12
11. Identify the Right Pedal (12) and the right Pedal
Arm (11). Orient the Right Pedal and the right
Pedal Arm as shown.
Attach the Right Pedal (12) to the right Pedal
Arm (11) with two M10 x 45mm Bolts (91), two
M10 Washers (92), and two M10 Locknuts (93);
start both Bolts, and then tighten them.
Attach the Left Pedal (13) to the left Pedal
Arm (11) in the same way.
11
91
12
11
11
13
92
93
10. Finger tighten an M8 x 20mm Hex Screw (57)
with an M8 Split Washer (63), an M8 Large
Washer (72), and an M8 Plastic Washer (27) into
the right end of the Upright Axle (26).
Then, tighten both M8 x 20mm Hex Screws (57)
at the same time.
Next, identify the two 8mm Dome Caps (83),
the four 17mm Dome Caps (not shown), and
the two 19mm Dome Caps (not shown).
Press an 8mm Dome Cap (83) firmly onto each
M8 Large Washer (72).
27
63
57
57
83
83
26
72
72
10

13
13
13. Identify the Right Crank Axle (16).
Apply grease to the Right Crank Axle (16) and
to a Nylon Spacer (102). Then, slide the Nylon
Spacer onto the Right Crank Axle.
Insert the Right Crank Axle (16) into the right
Pedal Arm Bracket (44), and firmly tighten the
Right Crank Axle clockwise into the right arm of
the Crank (18).
Next, firmly tighten the Right Crank Locknut
(36) and an M12 Split Washer (74) onto the
Right Crank Axle (16). Then, press a 19mm
Dome Cap (84) firmly onto the Right Crank
Locknut.
Repeat this step on the left side of the ellipti-
cal. Note: Turn the Left Crank Axle (not shown)
counterclockwise to tighten it, and use the Left
Crank Locknut (not shown).
84 36 74
Grease
102
16
18
44
12. Apply grease to an M10 x 70mm Bolt (60).
Attach the right Pedal Arm (11) to the right
Upper Body Leg (64) with the M10 x 70mm
Bolt (60), two M10 Washers (92), two M10
Plastic Washers (62), and an M10 Locknut (93)
as shown. Make sure to place the Plastic
Washers between the right Upper Body Leg
and the right Pedal Arm.
Then, press a 17mm Dome Cap (14) firmly onto
each M10 Washer (92).
Attach the left Pedal Arm (11) to the left
Upper Body Leg (64) in the same way.
12
14
60
92
92
11
11 64
62
64
93
14
Grease

14
15. While a second person holds the Console (23)
near the Upright (2), connect the wires on the
Console to the Upright Wire (31) and the Pulse
Wires (A).
Insert the excess wire into the Console (23) or
into the Upright (2).
Tip: Avoid pinching the wires. Attach the
Console (23) to the Upright (2) with four
M4 x 12mm Screws (66).
See step 5. Tighten the M8 x 20mm Screws (54)
and the M8 Locknuts (53).
15
2
31
66
Avoid pinching
the wires
23
A
16
16. Orient the Seat Carriage (61) and the Seat Post
(24) as shown.
Slide the Seat Carriage (61) into the Seat Post
(24). Then, tighten the Seat Knob (48) and an
M8 Washer (55) into the Seat Post and the Seat
Carriage.
24
61
55
48
14. The Console (23) can use two AA batteries (not
included); alkaline batteries are recommended.
Do not use old and new batteries together or
alkaline, standard, and rechargeable batter-
ies together. IMPORTANT: If the Console has
been exposed to cold temperatures, allow it
to warm to room temperature before insert-
ing batteries. Otherwise, you may damage
the Console or other electronic components.
Remove the battery cover from the back of the
Console (23), and insert batteries into the bat-
tery compartment (D). Make sure to orient the
batteries as shown by the diagram inside the
battery compartment. Then, reattach the bat-
tery cover.
14
23
D

15
18
18. Attach the Water Bottle Holder (81) to the
Upright (2) with two M4 x 12mm Screws (66).
81
66 2
19. Make sure that all parts of the hybrid trainer are properly tightened. Extra parts may be included. To
protect the floor or carpet from damage, place a mat under the hybrid trainer.
17
17. Insert the Seat Post (24) into the Frame (1).
Adjust the Seat Post (24) to the desired height,
and insert the Seat Post Knob (87) into the indi-
cated hole (E) in the Frame (1) and into one of
the adjustment holes (F) in the Seat Post.
Tighten the Seat Post Knob (87). Make sure
that the Seat Post Knob is inserted into
one of the adjustment holes (F) in the Seat
Post (24).
1
24
87
E
F

16
HOW TO MOVE THE HYBRID TRAINER
Due to the size and weight of the hybrid trainer,
moving it requires two persons. Stand in front of the
hybrid trainer, hold the upright (A), and place one foot
against one of the front stabilizer caps (B). Pull on the
upright and have a second person lift the rear stabilizer
(C) until the hybrid trainer will roll on the front stabilizer
caps. Carefully move the hybrid trainer to the desired
location, and then lower it to the floor.
HOW TO USE THE ELLIPTICAL MODE
To mount the hybrid trainer in the elliptical mode, hold
the handlebars (D) or the upper body arms (E) and
step onto the pedal (F) that is in the lower position.
Then, step onto the other pedal.
Push the pedals (F) until they begin to move with a
continuous motion. Note: The crank arms (G) can
turn in either direction. It is recommended that you
move the crank arms in the direction shown by the
arrow; however, for variety, you can turn the crank
arms in the opposite direction.
To dismount the hybrid trainer, wait until the pedals (F)
come to a complete stop. Note: The hybrid trainer
does not have a free wheel; the pedals will con-
tinue to move until the flywheel stops. When the
pedals are stationary, step off the higher pedal first.
Then, step off the lower pedal.
A
C
B
F
G
E
D
HOW TO USE THE HYBRID TRAINER

17
HOW TO USE THE UPRIGHT BIKE MODE
To use the hybrid trainer as an upright bike, adjust the
position of the seat post and the position of the seat.
For effective exercise, the seat should be at the proper
height. As you pedal, there should be a slight bend in
your knees when the pedals are in the lowest position.
To adjust the height of the seat, first loosen and
remove the seat post knob (H). Next, slide the seat
post upward or downward and align one of the adjust-
ment holes in the seat post with the hole in the frame.
Insert the seat post knob into the frame and the seat
post, and then tighten the seat post knob. Make sure
that the seat post knob is inserted into one of the
adjustment holes in the seat post.
To adjust the position of the seat, first loosen the seat
knob (I) a few turns. Then, move the seat forward or
backward to the desired position, and firmly tighten the
seat knob.
I
H

18
CONSOLE DIAGRAM FEATURES OF THE CONSOLE
The easy-to-use console features six modes that
provide instant exercise feedback during your
workouts.
Scan (SCAN)—This mode displays the time, speed,
distance, calories, and pulse modes, for a few seconds
each, in a repeating cycle.
Time (TMR)—This mode displays the elapsed time.
Note: If you set a time goal (see step 2 on page
19), this display will show the time remaining in your
workout.
Speed (SPD)—This mode displays your pedaling
speed, in miles per hour.
Distance (DST)—This mode displays the distance you
have pedaled during your workout, in miles. Note: If
you set a distance goal (see step 2 on page 19),
this display will show the distance remaining in your
workout.
Calories (CAL)—This mode displays the approximate
number of calories you have burned during your work-
out. Note: If you set a calorie-burning goal (see step
2 on page 19), this display will show the number of
calories still to be burned in your workout.
Pulse (PULSE)—This mode displays your heart rate
in beats per minute when you hold the handgrip heart
rate monitor (see step 4 on page 19). If you set
a target heart rate, (see step 2 on page 19), this
display will flash whenever your heart rate is above the
target.
Wichita
ELWL32115
WLEL32115.0

19
HOW TO USE THE CONSOLE
Make sure that batteries (not included) are installed in
the console (see assembly step 14 on page 14). If
there is a sheet of plastic on the console, remove the
plastic.
1. Turn on the console.
To turn on the console, press any button on the
console or simply begin pedaling.
2. Set a workout goal or a target heart rate if
desired.
To set a time, distance, or calorie-burning goal or
to set a target heart rate for your workout, press
the MODE button repeatedly until the word TMR,
DST, CAL, or PULSE appears in the display. Make
sure that the word SCAN does not appear in the
display.
Next, press the SET button repeatedly to set a goal
or a target heart rate. To set a goal or a target heart
rate quickly, hold down the SET button. To reset the
goal or target heart rate, press the RESET button.
3. Begin pedaling and follow your progress with
the display.
Scan mode—To select the scan mode, press the
MODE button repeatedly until the word SCAN
appears in the display.
Time, speed, distance, calories, pulse mode—
To select one of these modes for continuous
display, press the MODE button repeatedly until the
name of the desired mode appears in the display.
Make sure that the word SCAN does not appear in
the display.
As you exercise, the console will provide instant
feedback about your workout. If you have set a
workout goal, the display will show zeros when
you reach your goal; if you continue to exercise,
the display will begin to count upward. If you have
set a target heart rate, the display will flash when-
ever your heart rate is over the target.
To pause the console, stop pedaling. The word
STOP will appear in the display. To continue your
workout, simply resume pedaling.
To reset the display and all the modes to zero,
press and hold the Reset button for several
seconds.
4. Measure your heart rate if desired.
Note: If there
are sheets
of plastic on
the metal
contacts (A)
of the hand-
grip heart
rate monitor,
remove the
plastic. To
measure your heart rate, hold the handgrip heart
rate monitor, with your palms resting against the
contacts. Avoid moving your hands or gripping
the contacts tightly.
When your pulse is detected, your heart rate will
be shown in the display when the scan mode or
the pulse mode is selected. When your pulse is not
detected, a P will appear in the display. When you
set a target heart rate, the display will flash when-
ever your heart rate is over the target.
For the most accurate heart rate reading,
continue to hold the contacts for about 15
seconds. If your heart rate is not shown, make
sure that your hands are positioned as described.
Be careful not to move your hand excessively or
to squeeze the contacts tightly. For optimal perfor-
mance, clean the contacts using a soft cloth; never
use alcohol, abrasives, or chemicals to clean
the contacts.
5. When you are finished exercising, the console
will turn off automatically.
If the pedals do not move for a few seconds, the
console will pause.
The console has an auto-off feature. If the ped-
als do not move and the console buttons are not
pressed for a few minutes, the power will turn off
automatically to save the batteries.
A

20
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION: To assure continued compliance, use only shielded interface cables when connecting to
computer or peripheral devices. Changes or modifications not expressly approved by the party respon-
sible for compliance could void the user’s authority to operate this equipment.