ICON Health & Fitness HealthRider HRMC05080 User manual

Before the chest pulse sensor can be used, the
included receiver must be installed. Follow the steps
below to install the receiver.
Locate the
pulse sen-
sor cover
beneath
your tread-
mill console.
Using a
standard
screw-
driver (not
included), remove the two screws from the pulse
sensor cover. Discard the pulse sensor cover and
the screws.
Next, look
under the
console and
locate the
console wire
harness.
Plug the
receiver wire
harness fully
into the
console wire
harness.
Finally,
attach the
receiver to the console with the two included
screws. Be careful to avoid pinching the wire
harnesses.
2
1
HealthRider®Chest Pulse Sensor
How to Install the Receiver
Limited Warranty
Receiver
Screws
Receiver
Wire
Harness
Model No.
HRMC05080
WHAT IS COVERED—The HealthRider®Chest Pulse Sensor (“product”) is
warranted to be free of all defects in material and workmanship.
WHO IS COVERED—The original purchaser or any person receiving the
product as a gift from the original purchaser.
HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), war-
rants the product for one year after the date of purchase.
WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you,
without charge, any replacement part or component, or, at our option, we will
replace the product.
WHAT IS NOT COVERED—Any failures or damage caused by unautho-
rized service, misuse, accident, negligence, improper assembly or installa-
tion, alterations, modifications without our written authorization or by failure
on your part to use, operate, and maintain as set out in this manual (“man-
ual”). This warranty does not extend to products used for commercial or
rental purposes or to products used as store display models.
WHAT YOU MUST DO—Always retain proof of purchase, such as your bill
of sale; store, operate, and maintain the product as specified in the manual;
notify our Customer Service Department of any defect within 10 days after
discovery of the defect; as instructed, return any defected part for replace-
ment or, if necessary, the entire product, for repair.
MANUAL—It is VERY IMPORTANT THAT YOU READ THIS MANUAL be-
fore using the product. Remember to follow the instructions specified in this
manual to assure proper operation and your continued satisfaction.
HOW TO GET PARTS AND SERVICE—Simply call our Customer Service
Department at 1-800-999-3756 and tell them your name and address and
the model number of your product. They will tell you how to get a part re-
placed, or advise you how to ship the product for service. Before shipping,
always obtain a Return Authorization Number (RA No.) from our Customer
Service Department; securely pack your product (save the original shipping
carton if possible); put the RA No. on the outside of the carton and insure the
product. Include a letter explaining the product or problem and a copy of
your proof of purchase if you believe the service is covered by warranty.
ICON is not responsible or liable for indirect, special or consequential dam-
ages arising out of or in connection with the use or performance of the prod-
uct or damages with respect to any economic loss, loss of property, loss of
revenues or profits, loss of enjoyment or use, costs of removal, installation or
other consequential damages of whatsoever nature. Some states do not
allow the exclusion or limitation of incidental or consequential damages.
Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties
and any implied warranties of merchantability or fitness for a particular pur-
pose is limited in its scope and duration to the terms set forth herein. Some
states do not allow limitations on how long an implied warranty lasts.
Accordingly, the above limitation may not apply to you. No one is authorized
to change, modify or extend the terms of this limited warranty. This warranty
gives you specific legal rights and you may have other rights which vary from
state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321
Pulse
Sensor
Cover
Screws
Console
Wire
Harness
Congratulations for selecting the state-of-the-art
HealthRider®chest pulse sensor. The HealthRider®
chest pulse sensor is designed to continuously monitor
your heart rate as you exercise on your treadmill. In
addition, the chest pulse sensor enables you to use
the console’s two pulse programs.
Before using the chest pulse sensor, please read
this manual carefully. If you have questions after
reading this manual, please call our Customer
Service Department toll-free at 1-800-999-3756,
Monday through Friday, 6 a.m. until 6 p.m.
Mountain Time (excluding holidays).

The chest pulse sensor consists of two components:
the chest strap and the sensor unit. Follow the steps
below to put on the chest pulse sensor.
Refer to the inset drawing above. Insert the tab
on one end of the chest strap through one end of
the sensor unit as shown. Make sure to press the
end of the sensor unit under the buckle on the
chest strap.
Wrap the
sensor unit
and the
chest strap
around your
chest.
Attach the
free end of
the chest strap to the sensor unit as described
above. Adjust the length of the chest strap, if nec-
essary. The chest pulse sensor should be under
your clothing, against your skin, and as high
under the pectoral muscles or breasts as is com-
fortable. Make sure that the logo is facing forward
and is right-side-up.
Pull the
sensor unit
away from
your body a
few inches
and locate
the two
electrode
areas on the inner side. Using a saline solution
such as saliva or contact lens solution, wet both
electrode areas. Return the sensor unit to a posi-
tion against your chest.
CHEST PULSE SENSOR TROUBLE-SHOOTING
If the chest pulse sensor does not function properly,
or if the displayed pulse is excessively high or low,
try the trouble-shooting steps below.
• Make sure that the chest pulse sensor is under your
clothing, against your skin, and as high under the
pectoral muscles or breasts as is comfortable. Note:
If the chest pulse sensor does not function when po-
sitioned as described, try moving it slightly lower or
higher on your chest.
• Make sure that the logo on the sensor unit is facing
forward and is right-side-up.
• Each time you use the chest pulse sensor, use saline
solution such as saliva or contact lens solution to wet
the two electrode areas on the sensor unit (see the
drawing near the bottom of this page). If pulse read-
ings do not appear until you begin perspiring, re-wet
the electrode areas.
• As you walk or run on the treadmill, make sure that
you are near the center of the walking belt and within
arm’s length of the console. For the console to dis-
play pulse readings, the user must be within
arm’s length of the console.
• The chest pulse sensor is designed to work with
people who have normal heart rhythms. Pulse read-
ing problems may be caused by medical conditions
such as premature ventricular contractions (pvcs),
tachycardia bursts, and arrhythmia.
• The operation of the chest pulse sensor can be af-
fected by magnetic interference caused by high
power lines or other sources. If it is suspected that
magnetic interference may be causing a problem,
try relocating the treadmill.
• If the chest pulse sensor still does not function prop-
erly, test the chest pulse sensor in the following way:
Hold the chest pulse sensor and place your thumbs
over the electrode areas as shown at the left.
Next, hold the chest pulse sensor near the console.
While holding one thumb stationary, begin tapping
the other thumb against the electrode area at a rate
of about one tap per second. Check the pulse reading
on the console.
3
2
1
How to Put On the Chest Pulse Sensor
2
Logo
Electrode Areas
Chest Strap
Sensor Unit
Tab
Buckle
Sensor
Unit

3
How to Use the Chest Pulse Sensor
The chest pulse sensor is designed to continuously
monitor your heart rate as you exercise on your tread-
mill. In addition, the chest pulse sensor enables you to
use the console’s two pulse programs. Both programs
automatically control the speed and incline of the
treadmill to keep your heart rate near preset levels.
Before using the pulse programs, make sure that the
treadmill power cord is properly plugged in and that the
on/off switch located on the front of the treadmill is in the
“on” position (see your treadmill user’s manual).
Follow the steps at the right and on the following page
to use a pulse program.
Insert the key fully into the console.
Stand on the foot rails of
the treadmill. Find the clip
attached to the key, and
slide the clip onto your
clothing. Next, insert the
key fully into the console.
Put on the chest pulse sensor.
You must put on the chest pulse sensor to use a
pulse program.
Select one of the pulse programs.
To select a pulse
program, the MANUAL
indicator or a program
indicator must be flash-
ing. If necessary, hold
down the STOP/PAUSE
button for two seconds until the MANUAL indicator
is flashing. Next, press the SELECT + or – button
repeatedly until one of the two Pulse program indi-
cators is flashing. Then, press the ENTER button.
A profile of the program you have selected will
appear in the program display.
3
2
1
Program
Indicator
•If the chest pulse sensor does not function properly
after you have followed all of the above instructions,
the battery should be replaced in the following way:
Locate the battery
cover on the back of
the sensor unit. Insert
a coin into the slot in
the cover, turn the
cover counterclock-
wise, and remove the
cover.
Remove the old bat-
tery and insert a new
CR 2032 battery.
Make sure that the
battery is turned so
the writing is on
top. Replace the
battery cover and
turn it clockwise to
close it.
CHEST PULSE SENSOR CARE
• Dry the chest pulse sensor after each use. The
chest pulse sensor is activated when the electrode
areas are wetted and it is put on; the chest pulse
sensor shuts off when it is removed and the elec-
trode areas are dried. If the chest pulse sensor is not
dried after each use, it may remain activated longer
than necessary, draining the battery prematurely.
• Store the chest pulse sensor in a warm, dry place.
Do not store the chest pulse sensor in a plastic bag
or other container that may trap moisture.
• Do not expose the chest pulse sensor to direct
sunlight for extended periods of time. Do not expose
the chest pulse sensor to temperatures above 122°F
(50°C) or below 14°F (-10°C).
• Do not excessively bend or stretch the sensor unit
when using or storing the chest pulse sensor.
• Clean the sensor unit using a damp cloth—never
use alcohol, abrasives, or chemicals.
CR 2032
Battery
WARNING: If you have an implanted medical
device such as a pacemaker, check with your
physician before using the chest pulse sensor.
WARNING: If you have heart problems, or if
you are over 60 years of age and have been
inactive, do not use the pulse programs.
WARNING: If you are taking medication regu-
larly, consult your physician to find whether it
will affect your exercise heart rate.

Enter your weight.
When a pulse program is
selected, a weight
setting will begin to flash
in the CALORIES/FAT
CALORIES display. You
must enter your weight to
use a pulse program. If you have already entered
your weight, press the ENTER button. If you need
to enter your weight, press the SELECT buttons.
When the correct weight is shown, press the
ENTER button.
Enter your age.
After your weight is
entered, an age setting
will begin to flash in the
PULSE display. You
must enter your age to
use a pulse program. If
you have already entered your age, press the
ENTER button. If you need to enter your age,
press the SELECT buttons. When the correct age
is shown, press the ENTER button.
Press the START button or the SPEED + button
to start the program.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
Each program consists of twenty 60-second or 90-
second segments. One pulse setting is programmed
for each segment. The pulse setting of the first
segment is shown
in the flashing
current segment
column of the
program display.
The pulse set-
tings of the next
twelve segments
are shown in the
twelve columns to the right. When only three sec-
onds remain in the first segment, both the current
segment column and the column to the right will
flash. When the first segment is completed, a
series of tones will sound and all pulse settings
will move one column to the left. The pulse setting
of the second segment will then be shown in the
current segment column. If necessary, the speed
and/or incline of the treadmill will automatically
change to keep your pulse near the pulse setting
of the second segment. The program will continue
in this way until all twenty segments are com-
pleted. The walking belt will then slow to a stop
and the program will be completed.
If your pulse is not detected during the program,
the letters “PLS” will flash in the PULSE display.
In addition, the speed and/or incline of the tread-
mill may automatically decrease. (See CHEST
PULSE SENSOR TROUBLE-SHOOTING on
page 2.)
Minor adjustments can be made to the speed or
incline of the treadmill during the program by
pressing the SPEED or INCLINE buttons.
However, if you increase the speed, the incline will
automatically decrease; if you decrease the
speed, the incline will increase. If you increase the
incline, the speed will automatically decrease; if
you decrease the incline, the speed will increase.
The console will always attempt to keep your
pulse near the current pulse setting of the pro-
gram.
To stop the program for a moment, press the
STOP/PAUSE button. The displays will pause and
the TIME display will begin to flash. To restart the
program, press the START button or the SPEED
+
button. To end the program at any time, hold
down the STOP/PAUSE button for two seconds.
The console will then be in the same state as if
the key had just been inserted.
Follow your progress with the LED displays.
See your treadmill user’s manual.
When the program is completed, remove the
key from the console.
Make sure that the incline of the treadmill is at
1%. The incline must be at 1% when the tread-
mill is folded to the storage position, or the
treadmill will be damaged. Remove the key from
the console and put it in a safe place. In addition,
move the on/off switch to the “off” position.
8
7
6
5
4
Current Segment
Part No. 152946 J00765AC R0499B Printed in USA © 1999 ICON Health & Fitness, Inc.
HealthRider®is a registered trademark of ICON Health & Fitness, Inc.