ICON ITSTC73 Series Assembly instructions

SAFETY

Page 1
TOOL STORAGE SAFETY
For technical questions, please call 1-888-866-5797. (2022 version)
IMPORTANT SAFETY
INSTRUCTIONS
When using your garage equipment,
basic safety precautions should always be
followed, including the following:
1. To prevent serious injury and DEATH from tipping,
Do not have more than one drawer open at a time.
2. DO NOT SIT, STAND OR CLIMB ON THIS ITEM.
DO NOT STEP IN OR ON DRAWERS.
3. Unplug roll cab before drilling mounting
holes to mount workcenter hutch.
4. Do not allow children to play with or near this
item. This item is NOT children’s furniture.
5. Do not exceed weight capacity. Do not exceed
drawer weight capacity, based on connected pair
of slides. Evenly distribute load from bottom up.
Uneven loading causes tipping. Be aware of
dynamic loading! Sudden load movement may
briefly create excess load causing tipping.
6. Close and lock drawer(s) before moving.
Do not pull, push to move.
7. Center an overhead or chest securely
within lip on top of chest or cabinet.
8. Place an overhead or chest on top of
matching chest or cabinet only.

Page 2
TOOL STORAGE SAFETY
For technical questions, please call 1-888-866-5797. (2022 version)
9. Do not place objects on top of an
overhead or hang objects off side.
10. Have assistant help place an overhead or
chest on top of chest or cabinet.
11. Use only on a flat, level, hard and smooth surface
capable of safely supporting a fully loaded Chest.
Use care when rolling unit over concrete seams.
12. Do not lift while loaded.
13. Do not use as a stand-alone unit.
14. Wear ANSI-approved safety goggles and
heavy-duty work gloves during assembly.
15. Read instruction manual before assembly and/or use.
16. Assemble only according to these instructions.
Improper assembly can create hazards.
17. Do not operate equipment with a damaged cord or if
the equipment has been dropped or damaged – until
it has been examined by a qualified service person.
18. Do not let a cord hang over the edge of the
table, bench, or counter or come in contact
with hot manifolds or moving fan blades.
19. If an extension cord is necessary, a cord with a current
rating equal to or more than that of the equipment should
be used. Cords rated for less current than the equipment
may overheat. Care should be taken to arrange the
cord so that it will not be tripped over or pulled.

Page 3
TOOL STORAGE SAFETY
For technical questions, please call 1-888-866-5797. (2022 version)
20. Always unplug equipment from electrical outlet when
not in use. Never use the cord to pull the plug from
the outlet. Grasp plug and pull to disconnect.
21. Loop cord loosely around equipment when storing.
22. To reduce the risk of electric shock or fire,
never overload receptacles. Refer to markings
for the proper load on receptacles.
23. To reduce the risk of electric shock, do not
use on wet surfaces or expose to rain.
24. To reduce the risk of fire, do not operate equipment in the
vicinity of open containers of flammable liquids (gasoline).
25. Adequate ventilation should be provided when
working on operating internal combustion engines.
26. Keep hair, loose clothing, fingers, and all
parts of body away from moving parts.
27. Weight capacity and other product capabilities apply
to properly and completely assembled product only.
28. Use only as described in this manual. Use only
manufacturer’s recommended attachments.
29. Keep assembly area clean and well lit.
30. Do not assemble when tired or when under the
influence of alcohol, drugs or medication.
31. Keep bystanders out of the area during assembly.

Page 4
TOOL STORAGE SAFETY
For technical questions, please call 1-888-866-5797. (2022 version)
32. To reduce the risk of injury, close supervision is necessary
when this product will be used around children.
33. Use as intended only.
34. Inspect before every use;
do not use if parts are loose or damaged.
35. Maintain product labels and nameplates. These carry
important safety information. If unreadable or missing,
contact Harbor Freight Tools for a replacement.
SAVE THESE
INSTRUCTIONS.

Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
TM
73" TOP CHEST
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 22i
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright©2022 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using
this product.
Failure to do so can result in
serious injury.
SAVE THIS MANUAL.

Page 1
73" TOP CHEST
For technical questions, please call 1-888-866-5797.
Specifications
Drawer Weight Capacity
(Evenly distributed
from bottom up.)
265 lb per connected
pair of slides
Model Color Item
ITSTC73R Red 56140
ITSTC73BLU Blue 56300
ITSTC73BLK Black 56301
ITSTC73GN Green 56302

Page 2
73" TOP CHEST
For technical questions, please call 1-888-866-5797.

Page 3
73" TOP CHEST
For technical questions, please call 1-888-866-5797.
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY
INFORMATION section at the beginning of this
document including all text under subheadings
therein before set up or use of this product.
1. Assemble on a flat, level, hard and smooth surface
capable of safely supporting a fully loaded Chest.
2. Bolt Handles (2) to each end of the Housing using two
M8 Handle Bolts (3) each. Tighten hardware securely.
Housing Handle (2)
Handle
Bolt (3)
Figure A
3. Remove Mat from top of 73" Roll Cab.
4. Place Chest atop fully assembled Roll Cab.
5. Remove top Drawers from Roll Cab.
6. Use four Bolts (12) from within the Roll Cab
to attach the Top Chest to the top.
7. Reinstall the top Drawers into the Roll Cab.

Page 4
73" TOP CHEST
For technical questions, please call 1-888-866-5797.
Reconfiguring Drawers
1. The Drawers can be rearranged.
WARNING! TO PREVENT SERIOUS INJURY AND
DEATH FROM TIPPING: All drawers must be reinstalled
before use. Do not use a partially assembled Chest.
2. Remove the Drawers you want to move.
To remove a Drawer:
a. Slide the Drawer out until it stops
and empty it completely.
b. There is a small lever at the end of each
Chest Slide (17). Push up on the right lever,
and push down on the left lever.
c. While holding the levers, slide the Drawer out
completely and set it on a flat, stable surface.
Chest Slide (17)
lever
Figure B
3. After removing the Drawers, check where the slides
are positioned on them. All the slides on each
Drawer must be fully supported by Chest Slides.
4. Reposition Chest Slides as needed to properly support
the Drawers as explained in the two following steps.

Page 5
73" TOP CHEST
For technical questions, please call 1-888-866-5797.
5. Chest Slide Removal (tools sold separately):
a. With the Chest Slide extended,
remove the Slide Screw (18).
Slide
Screw (18)
Figure C
b. Gently pry the Chest Slide outward in
the location shown and raise the end of
the Chest Slide to disengage it.
Chest
Slide
Figure D

Page 6
73" TOP CHEST
For technical questions, please call 1-888-866-5797.
6. Chest Slide installation:
a. Align the tabs on the
Chest Slide with the
holes on the side of
the Housing. Align
the rear tab first, then
lower the front tabs
into the front holes.
b. Align the screw
hole in the center
of the Chest Slide
with the screw hole
on the Housing.
Secure it with a Slide Screw.
7. Install the Drawers according to the following instructions:
a. Select a properly-sized Drawer to install.
b. Confirm that all Chest Slides are properly
aligned with the slides on the Drawer.
c. Slide all Chest Slides out fully.
d. Confirm that ball bearing racks are
at the front of each Slide.
e. Carefully partially slide the Drawer in and check
again that all slides are engaging properly.
NOTICE: DO NOT FORCE THE DRAWER.
If the Drawer does not slide in easily, the slides are
likely misaligned or not installed correctly.
f. Slide the Drawer in completely.
g. Slide it back out to make sure the slides
keep it from coming disengaged.
h. Slide the Drawer closed.
holes
Figure E

Page 7
73" TOP CHEST
For technical questions, please call 1-888-866-5797.
Operation Instructions
Read the ENTIRE IMPORTANT SAFETY
INFORMATION section at the beginning of this
document including all text under subheadings
therein before set up or use of this product.
1. Hold both handles securely and carry the Chest to the
desired location. Have someone assist as needed.
2. Place only on a flat, level, hard and smooth surface
capable of safely supporting a fully loaded Chest.
Unlock Drawers, and fill Chest evenly, from bottom
to top. Do not exceed weight capacities.
Detent Force Adjustment
1. Each slide on the Drawers has a dial to adjust the
amount of force required to open the Drawer.
2. Turn the knob on the end of the Drawer slide
to the desired detent force setting.
3. Adjust all slides on a Drawer to the same
detent force setting. Using different
detent force settings on a single Drawer may cause
uneven slide motion and damage the slides.
detent
adjustment
knob
1
2
3
4
5
6
Figure F

Page 8
73" TOP CHEST
For technical questions, please call 1-888-866-5797.

Page 9
73" TOP CHEST
For technical questions, please call 1-888-866-5797.
Maintenance and Servicing
Procedures not specifically explained
in this manual must be performed
only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If any part becomes
damaged, have the problem corrected before further use.
1. PERIODICALLY, inspect the general
condition of the Chest. Check for:
• loose hardware,
• misalignment or binding of moving parts,
• cracked or broken parts,
• any other condition that may affect its safe operation.
2. Wipe external surfaces of the Chest with clean cloth.

Page 10
73" TOP CHEST
For technical questions, please call 1-888-866-5797.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS
PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY.
NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED
TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT
HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS
AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS, AND
NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS
TO THE ORIGINAL PRODUCT OR REPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Serial Number Here:
Note: If product has no serial number, record
month and year of purchase instead.
Note: Some parts are listed and shown for illustration
purposes only, and are not available individually as
replacement parts. Parts may not be interchangeable.
Specify UPC number when ordering:
Red: 56140, UPC 792363561402
Blue: 56300, UPC 792363563000
Black: 56301, UPC 792363563017
Green: 56302, UPC 792363563024

Page 11
73" TOP CHEST
For technical questions, please call 1-888-866-5797.
Parts List and Diagram
Parts List
Part Description Qty
1 Chest 1
2 Handle 2
3 M8x65 Handle Bolt 4
4 Lock 1
5 Lock Connector 1
6 M4x10 Screw 1
7 M4 Nut 1
8 Lock Bar 1
9 Drawer Trim End Cap 4
10 Brand 1
11 Front Trim 4
12 M8x20 Bolt 4
13 Drawer Trim 12
14 Drawer EVA liner 12
15 Drawer Trim 6
16 Drawer EVA liner 6
17 Drawer Slide Pair
(includes a left & right slide)
18
18 Slide Screw (not shown) 36
19 Top Mat (not shown) 1
ADrawer A 6
B Drawer B 6
C Drawer C 3
D Drawer D 3

Page 12
73" TOP CHEST
For technical questions, please call 1-888-866-5797.
Assembly Diagram