Icop IBW-6954 User manual

ICOP Technology Inc.
User Manual
IBW-6954
A PC/104 embedded solution on
Intel® Quad-core Processor
(Braswell Family)
Version 1.0

IBW35 User Manual
ICOP Technology Inc. I
Copyright
The information in this manual is subject to change without notice for continues
improvement in the product. All rights are reserved. The manufacturer assumes no reasonability
for any inaccuracies that may be contained in this document and makes no commitment to
update or to keep current the information contained in this manual.
No part of this manual may be reproduced, copied, translated or transmitted, in whole or in
part, in any form or by any means without the prior to written permission of ICOP Technology
Inc.
Copyrightⓒ 2020 ICOP Technology Inc.

IBW35 User Manual
ICOP Technology Inc. II
Revision History
Revision Date Remark
1.0 March 11, 2020 First version release

IBW35 User Manual
ICOP Technology Inc. III
Table of Contents
1 General Information ........................................................................................... 1
1.1 Overview ....................................................................................................................................... 1
1.2 Block diagram ................................................................................................................................ 1
1.3 Specifications ................................................................................................................................. 2
1.4 Ordering Information .................................................................................................................... 4
1.4.1 IBW-6954 ................................................................................................................................ 4
1.4.2 Optional Accessary .................................................................................................................. 4
2 Hardware Information ....................................................................................... 5
2.1 Dimension ..................................................................................................................................... 5
2.2 Board Outline ................................................................................................................................ 6
2.3 Connector and Jumper Summary ................................................................................................... 7
2.4 Pin Assignments & Jumper Settings ............................................................................................... 8
J2: LPC Header ................................................................................................................................ 8
J5: LAN ........................................................................................................................................... 8
J7: HDMI ......................................................................................................................................... 9
J9: MiniPCIe .................................................................................................................................. 10
J10A & J10B: PC/104 .................................................................................................................... 11
J11: Power for SATA HDD ........................................................................................................... 12
J12: SATA DOM ........................................................................................................................... 12
J13: Speaker ................................................................................................................................... 12
J14: Jumper Selection for AT/ATX ............................................................................................... 13
J15: CMOS Battery ......................................................................................................................... 13
J16: Line-out .................................................................................................................................. 13
J17: MIC-in .................................................................................................................................... 14
J18: I2C .......................................................................................................................................... 14

IBW35 User Manual
ICOP Technology Inc. IV
J19: PNT(default)/GPIO ............................................................................................................... 15
J20: Reset ....................................................................................................................................... 15
J21: Power selection for INV1 ....................................................................................................... 15
J23: Power Button .......................................................................................................................... 16
J25: COM1 (RS232) ....................................................................................................................... 16
J26: COM2 (RS232) ....................................................................................................................... 17
J27: COM3 (RS232/422/485) ........................................................................................................ 17
J28: COM4 (RS232/422/485) ........................................................................................................ 18
J30: Power Connector .................................................................................................................... 18
J33: USB(2.0) ................................................................................................................................. 18
J34: VGA ....................................................................................................................................... 19
J35: 4-pin Power Source ................................................................................................................. 19
J36: USB(2.0) ................................................................................................................................. 19
LVDS1: LVDS ............................................................................................................................... 20
INV1: LCD Backlight Control ....................................................................................................... 20
Technical Support Directly from ICOP ................................................................ 21
User Manual Feedback ............................................................................................. 21
Warranty ...................................................................................................................... 22

IBW35 User Manual
ICOP Technology Inc. 1
1 General Information
1.1 Overview
IBW-6954, a PC/104 embedded solution for industrial application based on Intel® Braswell
Quad-Core CPU with 4GB DDR3L RAM onboard, provides stable and powerful computing
performance.
IBW-6954 supports Gigabit LAN, 4x COM, 4x USB, I2C, Parallel, Mini PCIe, HDMI,
LVDS, VGA, and SATA interface for storage for development use.
1.2 Block diagram

IBW35 User Manual
ICOP Technology Inc. 2
1.3 Specifications
Processor
Intel® AtomTM x5-E8000, 2.00GHz (Burst), 1.04GHz Quad Core
Intel® Pentium® N3710, 2.56GHz (Burst), 1.6GHz Quad Core (Option)
Intel® Celeron® N3160, 2.24GHz (Burst), 1.6GHz Quad Core (Option)
System Memory 4GB DDR3L 1600MHz onboard
BIOS UEFI BIOS
Bus MiniPCIe (full-size) x1 ISA Bus x1
Display
Hardware decoding: H.265, MPEG2, MVC, VC-1, VP8, WMV9, and JPEG/MJPEG formats
Hardware encoding: H.264, MVC, and JPEG/MJPEG formats
VGA: resolutions up to 1920 x 1200 @ 60Hz
HDMI: resolutions up to 2560 x 1600 @ 60Hz, 24bpp
LVDS: resolutions up to 1920 x 1200 @ 60Jz, in dual LVDS bus mode
LAN Realtek 8111H GbE x1
HD Audio Realtek ALC262 VD
Disk Support SATA device x1
mSATA device x1 (Option)*
I/O Interface
COM x4 (2 for RS232/422/485)
I2C x1
USB 2.0 x4
Parallel/16-bit GPIO x1
Audio (Line-out/MIC-in)
*mSATA support must be configured from MiniPCIe interface through H/W modification

IBW35 User Manual
ICOP Technology Inc. 3
Connectors
5.40mm 7-pin Standard SATA connector x1
2.00mm 26-pin box header for Printer x1
2.00mm 14-pin header for LPC x1
2.00mm 12-pin header for LAN port x1
2.00mm 12-pin header for VGA port x1
2.00mm 10-pin box header for COM x4
2.00mm 10-pin box header for USB x4
2.00mm 2-pin box header for SATA Power x1
2.00mm 2-pin header for AT/ATX mode x1
2.00mm 2-pin header Power button x1
2.00mm 2-pin header for Reset x1
1.25mm 30-pin wafer for LVDS x1
1.25mm 4-pin header for I2C x1
1.25mm 4-pin wafer for Line-out/MIC-in x2
1.25mm 2-pin header for CMOS battery x1
2-pin header for Speaker
Standard PC/104 connector x1
HDMI connector x1
Terminal block for Power input x1
Mini PCIe slot x1
Power
Requirement 5V DC
Operating Temp. 0°C to +60°C
Dimensions 116mm x 96mm
Weight 81g
O/S Support
Windows 10
Windows 7 (64bits)
Linux

IBW35 User Manual
ICOP Technology Inc. 4
1.4 Ordering Information
1.4.1 IBW-6954
Product Name IBW-6954-E4 IBW-6954-A4 IBW-6954-B4
Processor 1.04GHz
(Intel® AtomTM x5-E8000)
1.60GHz
(Intel® Pentium® N3710)
1.60GHz
(Intel® Celeron® N3160)
System Memory 4GB DDR3L 1600MHz
Accessary CABLE-SATA-30CM x1
1.4.2 Optional Accessary
Cable-set-6954 Cable set for IBW-6954 (RS232x4, USBx2, PRINT, Audio x2, LAN, VGA)

IBW35 User Manual
ICOP Technology Inc. 5
2 Hardware Information
2.1 Dimension
Top:
Bottom:

IBW35 User Manual
ICOP Technology Inc. 6
2.2 Board Outline
Top:
Bottom:

IBW35 User Manual
ICOP Technology Inc. 7
2.3 Connector and Jumper Summary
Nbr. Name Type of Connections Nbr of Pin
J2 LPC Header Pin Header, 2.0mm, 7x2 14
J5 LAN Pin Header, 2.0mm, 6x2 12
J7 HDMI Wafer, 1.0mm, 10x2 20
J9 MiniPCIe Standard Mini PCIe connector
J10A PC/104 Standard PC/104 connector
J10B
J11 Power for SATA HDD Box Header, 2.0mm, 2x1 2
J12 SATA DOM SATA 7p Connector, 7x1 7
J13 Speaker Pin Header, 2x1 2
J14 Jumper Selection for AT/ATX Pin Header, 2.0mm, 2x1 2
J15 CMOS Battery Wafer, 1.25mm, 2x1 2
J16 Line-out Wafer, 1.25mm, 4x1 4
J17 MIC-in Wafer, 1.25mm, 4x1 4
J18 I2C Wafer, 1.25mm, 4x1 4
J19 PNT/GPIO Box Header, 2.0mm, 13x2 26
J20 Reset Pin Header, 2.0mm, 2x1 2
J21 Power selection for INV1 Pin Header,2.0mm, 3x1 3
J23 Power Button Box Header, 2.0mm, 2x1 2
J25 COM1 (RS232) Box Header, 2.0mm, 5x2 10
J26 COM2 (RS232) Box Header, 2.0mm, 5x2 10
J27 COM3 (RS232/422/485) Box Header, 2.0mm, 5x2 10
J28 COM4 (RS232/422/485) Box Header, 2.0mm, 5x2 10
J30 Power Connector Terminal Block, 5.0mm, 2x1 2
J33 USB(2.0) Box Header, 2.0mm, 5x2 10
J34 VGA Box Header, 2.0mm, 6x2 12
J35 4-pin Power Source Pin Header, 2.54mm, 4x1 4
J36 USB(2.0) Box Header, 2.0mm, 5x2 10
LVDS1 LVDS Wafer, 1.25mm, 15x2 30
INV1 LCD Backlight Control Wafer, 2.0mm, 5x1 5

IBW35 User Manual
ICOP Technology Inc. 8
2.4 Pin Assignments & Jumper Settings
J2: LPC Header
14-pin header(2.0mm) for LPC bus.
Pin# Signal Name Pin# Signal Name
1 LPC_CLKOUT 2 GND
3 L_FRAME_N 4 NC
5 PLTRST_3P3_N 6 VCC5
7 LPC_AD3 8 LPC_AD2
9 VCC3 10 LPC_AD1
11 LCD_ADD 12 GND
13 LCD_SMB_CLK 14 LPC_SMB_DAT
J5: LAN
12-pin header(2.0mm) for LAN port.
Pin# Signal Name Pin# Signal Name
1 HGTX+1 2 HGTX-1
3 HGRX+1 4 HGRX-1
5 HGTXC+1 6 HGTXC-1
7 HGRXD+1 8 HGRXD-1
9 LED0+1 10 LED0
11 LED1+1 12 LED1/EESK

IBW35 User Manual
ICOP Technology Inc. 9
J7: HDMI
20-pin wafer(1.0mm) for HDMI.
Pin# Signal Name Pin# Signal Name
1 HDMI_DATA2_R_DP 2 -
3 HDMI_DATA2_R_DN 4 GND
5 GND 6 HDMI_CLK_R_DP
7 HDMI_DATA1_R_DP 8 HDMI_CLK_R_DN
9 HDMI_DATA1_R_DN 10 GND
11 GND 12 HDMI_DDPC_SCL
13 HDMI_DATA0_R_DP 14 HDMI_DDPC_SDA
15 HDMI_DATA0_R_DN 16 GND
17 VCC5_S 18 HDMI_HPD
19 GGND 20 GGND

IBW35 User Manual
ICOP Technology Inc. 10
J9: MiniPCIe
Standard 52-pin female Mini PCI Express connector.
Pin# Signal Name Pin# Signal Name
1 WAKE_(LAN)_3P3_N 2 VCC3P3_S
3 - 4 GND
5 - 6 -
7 PCIE2_CLKREQ2_N 8 -
9 GND 10 -
11 MINI_PCIE_CLK2_DN 12 -
13 MINI_PCIE_CLK2_DP 14 -
15 GND 16 -
Mechanical Key
17 - 18 GND
19 - 20 -
21 GND 22 PLTRST_3P3_N
23 PCIE2_RXP 24 VCC3P3_S
25 PCIE2_RXN 26 GND
27 GND 28 -
29 GND 30 SMB_CLK_P2
31 PCIE2_TXN 32 SMB_DAT_P2
33 PCIE2_TXP 34 GND
35 GND 36 XUSBD2-
37 GND 38 XUSBD2+
39 VCC3P3_S 40 GND
41 VCC3P3_S 42 -
43 GND 44 -
45 - 46 -
47 - 48 -
49 - 50 GND
51 - 52 VCC3P3_S
* [J9] could be configured as mSATA interface through H/W modification.

IBW35 User Manual
ICOP Technology Inc. 11
J10A & J10B: PC/104
Standard PC/104 connector.
J10A J10B
Pin# Signal Name Pin# Signal Name Pin# Signal Name Pin# Signal Name
B1 GND A1 IOCHCK# D1 GND C1 GND
B2 XXRSTDRV A2 SD7 D2 MECS16# C2 SBHE#
B3 VCC5V_S A3 SD6 D3 IOCS16# C3 LA23
B4 XIRQ9 A4 SD5 D4 IRQ10 C4 LA22
B5 -5V A5 SD4 D5 IRQ11 C5 LA21
B6 XDRQ2 A6 SD3 D6 IRQ12 C6 LA20
B7 -12V A7 SD2 D7 IRQ15 C7 LA19
B8 XOWS A8 SD1 D8 IRQ14 C8 LA18
B9 +12V A9 SD0 D9 DACK0# C9 LA17
B10 GND A10 IOCHRDY D10 DRQ0 C10 MEMR#
B11 SMEMW# A11 AEN D11 DACK5# C11 MEMW#
B12 SMEMR# A12 SA19 D12 DRQ5 C12 SD8
B13 IOW# A13 SA18 D13 DACK6# C13 SD9
B14 IOR# A14 SA17 D14 DRQ6 C14 SD10
B15 DACK3# A15 SA16 D15 DACK7# C15 SD11
B16 DRQ3 A16 SA15 D16 DRQ7 C16 SD12
B17 DACK1# A17 SA14 D17 VCC5V_S C17 SD13
B18 DRQ1 A18 SA13 D18 MASTER# C18 SD14
B19 REFRESH# A19 SA12 D19 GND C19 SD15
B20 SYSCLK A20 SA11 D20 GND C20 -
B21 IRQ7 A21 SA10
B22 IRQ6 A22 SA9
B23 IRQ5 A23 SA8
B24 IRQ4 A24 SA7
B25 IRQ3 A25 SA6
B26 DACK2# A26 SA5
B27 TC A27 SA4
B28 BALE A28 SA3
B29 VCC5V_S A29 SA2
B30 XXOSC A30 SA1
B31 GND A31 SA0
B32 GND A32 GND

IBW35 User Manual
ICOP Technology Inc. 12
J11: Power for SATA HDD
2-pin box header(2.0mm) for SATA HDD power.
Pin# Signal Name
1 VCC5V_S
2 GND
J12: SATA DOM
7-pin SATA connector(5.4mm) for SATA DOM.
Pin# Signal Name
1 GND
2 SATA_TXP
3 SATA_TXN
4 GND
5 SATA_RXN
6 SATA_RXP
7 GND
J13: Speaker
2-pin pin header for Speaker interface.
Pin# Signal Name
1 SPKR
2 VCC5_S

IBW35 User Manual
ICOP Technology Inc. 13
J14: Jumper Selection for AT/ATX
2-pin pin header(2.0mm) jumper selection for AT/ATX mode.
[J14] Closed  AT mode
[J14] Open  ATX mode
J15: CMOS Battery
2-pin wafer(1.25mm) for CMOS battery.
Pin# Signal Name
1 VCC3P3
2 GND
J16: Line-out
4-pin wafer(1.25mm) for Line-out interface.
Pin# Signal Name
1 LOUT_R
2 GND
3 LOUT_L
4 GND

IBW35 User Manual
ICOP Technology Inc. 14
J17: MIC-in
4-pin wafer(1.25mm) for MIC-in function.
Pin# Signal Name
1 MIC_IN_R
2 GND
3 MIC_IN _L
4 GND
J18: I2C
4-pin wafer(1.25mm) for I2C interface.
Pin# Signal Name
1 GND
2 I2C5_SDA_3P3
3 I2C5_SCL_3P3
4 VCC3

IBW35 User Manual
ICOP Technology Inc. 15
J19: PNT(default)/GPIO
26-pin box header(2.0mm) for Print or GPIO interface.
Pin# Signal Name Pin# Signal Name
1 STB-/GP87 2 PD0/GP70
3 PD1/GP71 4 PD2/GP72
5 PD3/GP73 6 PD4/GP74
7 PD5/GP75 8 PD6/GP76
9 PD7/GP77 10 ACK-/GP83
11 BUSY/GP82 12 PE/GP81
13 SLCT/GP80 14 AFD-/GP86
15 ERR-/ 16 INIT-/GP85
17 SLIN-/GP84 18 GND
19 GND 20 GND
21 GND 22 GND
23 GND 24 GND
25 GND 26 GND
J20: Reset
2-pin pin header(2.0mm) for Reset button.
Pin# Signal Name
1 RSTBTN
2 GND
J21: Power selection for INV1
3-pin pin header for INV1 power selection
Pin# Signal Name
1 5V
2 GND
3 12V
Pin1 & 2 Closed  VCC 5V
Pin2 & 3 Closed  VCC 12V