ICP DAS USA ET-2260 User manual

Technical support: servic[email protected] P1
ET-2260 Quick Start
v1.2, Jun. 2018
What’s in the box?
Related Information
The package includes the following items:
ET-2260 Module x 1
Quick Start x1
(This Document)
ET-2200 Series Product Page:
Documentation & Firmware:
NS-205/MDR-20-24 Product Page (optional):

Technical support: servic[email protected] P2
1
Connecting the Power and Host PC
1) Make sure your PC has workable network settings.
Disable or well configure your Windows firewall and Anti-Virus firewall first,
else the “Search Servers” on Chapter 5 may not work. (Please contact
with your system Administrator)
2) Connect both the ET-2260 and your PC to the same sub network or the
same Ethernet switch.
3) Supply power (+10~+30 VDC) to the ET-2260.
4) Verify that the “PWR”LED indicator
on the ET-2260 is flashing.
Red, OK

Technical support: servic[email protected] P3
2 Pin Assignments & Wiring Note
Pin Assignments:
Wire Connections:
Readback as 1 Readback as 0
+10 ~ +50 VDC OPEN or <4 VDC
+10 ~ +50 VDC OPEN or <4 VDC
Digital Input/
Counter
Sink
Source
To other channels
10K
DICOM
DIx
+-
To other channels
10K
DICOM
DIx
-+
To other channels
10K
DICOM
DIx
-+
To other channels
10K
DICOM
DIx
+-
Relay Close
Open
Close to GND
Dry
Contact
Relay Open
NOx
COMx
LOAD
AC/DC
Readback as 1
Readback as 0
Power Relay
ON State
OFF State
NOx
COMx
LOAD
AC/DC
To other channels
GND
DIx
+S5 V GND
DIx
+S5 V

Technical support: servic[email protected] P4
3 Wiring the DI and DO for Self-test
A tip for connecting the wire to the connector
A tip for removing the wire from the connector
1) Connect the NO0 pin (Pin01) to the GND pin (Pin02).
2) Connect the COM0 pin (Pin03) to the DI0 pin (Pin04).
NO0 01
COM0 02
02 GND
04 DI0

Technical support: servic[email protected] P5
4 Modbus Address
(0xxxx) DO address:
Begin
address
Points
Description
Bits
Per
Point
Range
Access
Type
0 (0x0)
1~6
Digital Output Channels
1
0: OFF, 1: ON
R/W
32 (0x20)
1
Clears the status of all high
latched DI channels
1
1: Clear
W
33 (0x21)
1
Clears the status of all low
latched DI channels
1
1: Clear
W
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
190
(0xBE)
1~6
Enables frequency
measurement for all DI
Channels
1
0: Disable
1: Enable
(Default: 0)
R/W/F
235
(0xEB)
1~6
Sets the Power-on value for
all DO Channels
1
0: OFF, 1: ON
(Default: 0)
R/W/F
267
(0x10B)
1~6
Sets the Safe value for all DO
Channels
1
0: OFF, 1: ON
(Default: 0)
R/W/F
“R”: Read; “W”: Write; “F”:Settings are recorded in flash memory by default
(1xxxx) DI address:
Begin
address
Points
Description
Bits
Per
Point
Range
Access
Type
0
(0x0)
1~6
Digital Input
1
0:Off
1:On
R
32
(0x20)
1~6
Digital latched status (high)
1
0:no
1:latched
R
64
(0x40)
1~6
Digital latched status (low)
1
0:no
1:latched
R
“R”: Read
Note
For detail “DI/DO Modbus Address”information, refer to Section 6.3 Modbus Register Table
of user’s manual (http://ftp.icpdas.com/pub/cd/6000cd/napdos/et2200/document/).

Technical support: servic[email protected] P6
5 Configuring Network Settings
1) Run the eSearch Utility.
The eSearch Utility is located at:
http://ftp.icpdas.com/pub/cd/6000cd/napdos/software/esearch/
2) Click the “Search Servers”to search your ET-2260.
3) Double-click your ET-2260 to configure the settings
Factory Default Settings of ET-2260:
IP Address
192.168.255.1
Subnet Mask
255.255.0.0
Gateway
192.168.0.1
4) Contact your Network Administrator to obtain a correct network
configuration (such as IP/Mask/Gateway). Enter the network settings
and click “OK”. Note: The ET-2260 will use the new settings 2 seconds
later.





Technical support: servic[email protected] P7
6 Testing your Ethernet I/O Module
1) Wait 2 seconds and click “Search Servers”button again to ensure the
ET-2260 is working well with new configuration.
2) Click the name of ET-2260 to select it.
3) Click the “Web”button to log in to the web configuration pages.
(Or enter the URL address of the ET-2260 in the address bar of the
browser.)
4) Enter the password (default: Admin)in the “login password”field and
click “Submit”.



Use the default
password: Admin


Technical support: servic[email protected] P8
5) In the “Home”page allows a simple test to be performed to verify the Digital
Input and Output functionality.
6) In the “Digital I/O”section, click the “DO0”button to ON (Red).
7) The corresponding DI becomes green for DI0 is ON.


