ICP DAS USA M-7033D User manual

M-7033D3 Channel RTD DAQ Module - QuickStart (May/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
1
M-7033D
3 Channel RTD Input Data Acquisition
Module
Quick Start Guide
Product Website:
https://www.icpdas-usa.com/m_7033d.html
http://www.icpdas-usa.com/dcon_utility_pro.html
1. Introduction
The M-7033D is a 3-channel RTD Input module that is used for measuring temperatures
via an RTD sensor and supports Pt100, Ni120, and Pt1000 type sensors. The module
allows 2/3/4-wire RTD connections and features open wire detection. In addition, the M-
7033 also includes 3000 VDC intra-module isolation, and supports lead resistance
elimination for 3/4-wire connections.
2. Terminal Assignment

M-7033D3 Channel RTD DAQ Module - QuickStart (May/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
2
3. Block/ Wiring Diagram
4. Default Settings
Default settings for the M-7024 module are as follows:
▫Protocol: Modbus RTU
▫Module address: 01
▫Analog output type: 0 ~ +10 V
▫Baud Rate: 9600 bps
▫Engineering unit format

M-7033D3 Channel RTD DAQ Module - QuickStart (May/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
3
5. Configuration
To install the module, follow the steps below:
1. Connect the thermistor analog input.
2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If
the host is only equipped with an RS-232 interface, then an RS-232 to RS-485
converter will be required.
3. Connect the module to the power supply using the +Vs and GND terminals. Note that
the voltage supplied should be in the range of +10 to +30V DC.
4. Open DCON utility pro
click on COM port(first icon).
It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to
search module. The default settings for the module can be found in Section 3. Click OK
after selecting the COM port setting.

M-7033D3 Channel RTD DAQ Module - QuickStart (May/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
4
5. DCON utility pro will search for the selected COM port according the setting
previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS
and the others modules.
6. Configuration I/O module setting on PC

M-7033D3 Channel RTD DAQ Module - QuickStart (May/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
5
7. For M-7000 modules using the Modbus RTU protocol, configure the module using the
following functions.
Sub-function 04h of Function 46h, see user manual Section 3.3.2
Sub-function 06h of Function 46h, see user manual Section 3.3.4
Sub-function 08h of Function 46h, see user manual Section 3.3.6
For M-7000 modules using the Modbus RTU protocol, use Function 04h to read the
data from the input channels. See user manual Section 3.2 for details.

M-7033D3 Channel RTD DAQ Module - QuickStart (May/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
6
8. If user doesn’t know command, user can select Address and ID, it will show some
refer commands as below. User can select necessary command to test or debug
modules.