ICP DAS USA I-7041 User manual

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
1
I-7041
14 Channel Isolated Digital Input Data
Acquisition Module
Quick Start Guide
Product Website:
https://www.icpdas-usa.com/i_7041
http://www.icpdas-usa.com/dcon_utility_pro.html
1. Introduction
The I-7041 provides 14 channels for digital input, each of which features
photo couple isolation. In addition, sink- or source-type digital input can be
selected via wire connections, and all channels are able to be used as 16-
bit counters. 4 kV ESD protection and 3750 VDC intra-module isolation are
standard. ICPDAS recommends selecting the "P" version of the digital input
module for industrial use.
2. Terminal Assignment

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
2
3. Block/ Wiring Diagram

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
3
4. Default Settings
Default settings for the I-7043 DIO modules are as follows:
。Module Address: 01
。DIO Type: Type 40
。Baud Rate: 9600 bps
。Checksum disabled
。J3 set to INIT mode enabled for I-7043/43D a
5. Configuration
To install the module, follow the steps below:
1. Connect the analog output.
2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If
the host is only equipped with an RS-232 interface, then an RS-232 to RS-485
converter will be required.
3. Connect the module to the power supply using the +Vs and GND terminals. Note that
the voltage supplied should be in the range of +10 to +30V DC.

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
4
4. Open DCON utility pro
click on COM port(first icon).
It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to
search module. The default settings for the module can be found in Section 3. Click OK
after selecting the COM port setting.

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
5
5. DCON utility pro will search for the selected COM port according the setting
previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS
and the others modules.
6. Configuration I/O module setting on PC

I-7041 14 Ch DI DAQ Module- QuickStart (Jun/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
6
7. For I-7000 modules, DCON utility pro terminal can send command to the module.
See user manual Sections 2 for details command.
Configure the module: sending the %AANNTTCCFF command. See user manual
Section 2 for details.
Read data from the input channels: send either the #AA or #AAN command to the
module.
8. If user doesn’t know command, user can select Address and ID, it will show some
refer commands as below. User can select necessary command to test or debug
modules.