ICP DAS USA M-7060 User manual


M‐70604‐channelDIand4‐channelRelayOutputDAQModule
‐QuickStart(Mar/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
1

M-7060
4-channel Digital Input and 4-channel Relay
Output Data Acquisition Module
Quick Start Guide
Product Website:
https://www.icpdas-usa.com/m_7060_m_7060d
http://www.icpdas-usa.com/dcon_utility_pro.html
1. Introduction
The 7060 series provides 4 digital input channels, 2 Form A and 2 Form C signal relay output
channels, while the M-7060P provides 4 digital input channels, 2 Form A and 2 Form C power
relay output channels. All digital input channels can be used as 16-bit counters. In addition, the
digital input channels can be selected either as sink- or source-type via wire connections. The
“D” versions of the 7060 series provide eight LED indicators that can be used to monitor the
status of the digital input and relay output. The “M” versions of the 7060 series support both the
Modbus RTU and DCON protocols, which can be configured via software. There are also
options for configuring power-on and safe values. 4 kV ESD protection and 3750 VDC intra-
module isolation are also provided to enhance noise protection capabilities in industrial
environments. The 7060 series is the ideal solution for small signal switching applications, while
the M-7060P is the perfect solution for high power applications.
2.TerminalAssignment



M‐70604‐channelDIand4‐channelRelayOutputDAQModule
‐QuickStart(Mar/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
2

3.Block/WiringDiagram


M‐70604‐channelDIand4‐channelRelayOutputDAQModule
‐QuickStart(Mar/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
3

4. Default Settings
。 Module Address: 01
。 DIO Type: Type 40
。 Baud Rate: 9600 bps
。 Checksum disabled
5. Configuration
To install the module, follow the steps below:
1. Connect the digital input and output.
2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If
the host is only equipped with an RS-232 interface, then an RS-232 to RS-485
converter will be required.
3. Connect the module to the power supply using the +Vs and GND terminals. Note that
the voltage supplied should be in the range of +10 to +30V DC.


M‐70604‐channelDIand4‐channelRelayOutputDAQModule
‐QuickStart(Mar/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
4



M‐70604‐channelDIand4‐channelRelayOutputDAQModule
‐QuickStart(Mar/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
5

4. Open DCON utility pro
click on COM port(first icon).
It can select multi-options such as Baud Rate, Protocol, Checksum, and Format
to search module. The default settings for the module can be found in Section 3.
Click OK after selecting the COM port setting.


M‐70604‐channelDIand4‐channelRelayOutputDAQModule
‐QuickStart(Mar/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
6

5. DCON utility pro will search for the selected COM port according the setting
previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS
and the others modules.
6. Configuration I/O module setting on PC


M‐70604‐channelDIand4‐channelRelayOutputDAQModule
‐QuickStart(Mar/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
7

7. For I-7000 modules, DCON utility pro terminal can send command to the module.
See user manual Sections 2 for details command.
Configure the module: sending the %AANNTTCCFF command. See user manual
Section 2 for details.
Read data from the input channels: send either the #AA or #AAN command to the
module.
8. If user doesn’t know command, user can select Address and ID, it will show some
refer commands as below. User can select necessary command to test or debug
modules.
