ICP DAS USA MDC-700 Series User manual

QuickStartforMDC‐700Series

July2015,Version1.01


ThisQuickStartintendstoprovideinformationneededtogetstartedwiththeMDC‐700series
modules.Pleasealsoconsulttheusermanualfordetailedinformationonthesetupanduseofthe
module.
What’sIntheBox?
Copyright © 2014 ICP DAS Co., Ltd. All Rights Reserved. E-mail: serv[email protected]
Quick Start for MDC-700 Series
Inadditiontothisguide,thepackageincludesthefollowingitems:




ModuleSoftwareUtilityCDRS‐232Cable
(CA‐0910)ScrewDriver
TechnicalSupport
UserManual
CD:\NAPDOS\Modbus\MDC_700\Document\
http://ftp.icpdas.com/pub/cd/8000cd/napdos/modbus/mdc_700/document/
Firmware
CD:\NAPDOS\Modbus\MDC_700\Firmware\
http://ftp.icpdas.com/pub/cd/8000cd/napdos/modbus/mdc_700/firmware/
ICPDASWebsite
http://www.icpdas.com
1

Copyright © 2014 ICP DAS Co., Ltd. All Rights Reserved. E-mail: serv[email protected]
1ConnectingtoPC,NetworkandPower
ThemoduleisequippedwithastandardEthernetport(RJ‐45)forconnectingtoanEthernet
Hub/SwitchandPC.Moreover,youcanalsoconnectthePCdirectlywithanEthernetcable.
Powersupply(+10~+30VDC)
Hub/Switch
Quick Start for MDC-700 Series
2

2
adefaultIPaddressof192.168.255.1.
uneedfirstassignavalidIPaddressofyournetworktotheMDC‐700moduleforaccessingthe



STEP2
isnew,withthedefaultIPaddressof192.168.255.1,youmustchosean
addressforthecomputerintherangeof192.168.255.2–192.168.255.253thatisnot
essonyourcomputerdependuponthetype
chitectureandoperatingsystemyouareusing.UsethecomputerHelpandSupport
functionalitytosearchfor“IPAddressing”.

AssigninganIPaddresstoMDC‐700
TheMDC‐700isanEthernetdevice,whichcomeswith
Yo
moduleandusingthebuilt‐inweb‐basedinterface.
STEP1PoweronthecomputerandtheMDCmodule.
SettheIPconfigurationonyourcomputer.
IftheMDCmodule
IP
alreadyinuse.

NOTE:DetailsonhowtochangetheIPaddr
ar


Copyright © 2014 ICP DAS Co., Ltd. All Rights Reserved. E-mail: serv[email protected]
Quick Start for MDC-700 Series
3
STEP3Openawebbrowserandgotothewebsiteathttp://192.168.255.1,where192.168.255.1is
theIPaddressofyourMDCmodule.


STEP4OpentheIPaddressconfigurationinterfacebyclickingtheEthernetConfiguration.


SETP5ChooseavalidIPaddressforyourMDCmodule.Makesurethattheaddressyoupickisnot
currentlyinusebyanotherdeviceonthenetwork.


NOTE:TheMDC‐700canberesettofactorydefaultsbyshortingtheRESETpintoGNDpin
over3seconds.TheLEDdisplaywillshow“RESET”asbelowandtheIPaddressset
previouslywillberemoved.



Copyright © 2014 ICP DAS Co., Ltd. All Rights Reserved. E-mail: serv[email protected]
3EnablingAdobeFlashPlayerinYourBrowser
YourbrowsermustsupportAdobeFlashPlayerandhaveitenabledinordertousethebuilt‐inweb
server.Ifyoudonothaveitinstalled,pleasegotothefollowingwebsiteandinstallit.

TheAdobeFlashPlayerDownloadCenter：
http://get.adobe.com/flashplayer/
4GototheWebSitetoCheckoutFunctions
Quick Start for MDC-700 Series
Gotothewebinterfaceathttp://xxx.xxx.xxx.xxx,wherexxx.xxx.xxx.xxxistheIPaddressofyour
MDCmodule.AnystandardbrowsercanbeusedtointerfacetheMDCmodule,suchasMozilla
Firefox,InternetExplorerorGoogleChrome.

NOTE:Ifyouhaven’tchangedthedefaultIPaddressofthemodule,pleasereferto“2.AssignanIP
addresstoMDC‐700”toconfigureit.


4