Icp das usa Pm-4324-400p-mtcp User manual

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 1

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 2

Chapter 1 Introduction .................................... 4

1.1. PM-4324 introduction........ 4

1.2. Caution............................. 5

1.2.1. Danger.............................. 5

1.3. Warning............................ 5

1.4. Product Warranty &

Customer Support............. 5

1.4.1. Limitation of Warranty....... 6

Chapter 2 Specifications................................. 7

2.1 Specifications.................... 7

2.2 Naming Rules................... 9

....................................................................... 9

Chapter 3 Installation.................................... 10

3.1 Inspection....................... 10

3.2 Safety............................. 10

3.2.1 Dimension and Latch...... 10

3.2.2 Mounting and Dismounting

....................................... 12

3.2.3 CT’s installation steps..... 13

Chapter 4 Wiring Diagrams...........................14

4.1 Connection......................14

4.2 Wiring..............................16

Chapter 5 Relay output & LED Indicator........18

5.1 Relay...............................18

5.2 LED Indicator ..................18

Chapter 6 Modbus-RTU communication........19

6.1.1 SW1－SW6 setting..........19

6.2 Modbus-RTU setting .......22

6.2.1 Specifications..................22

6.2.2 Modbus Register.............24

Chapter 7 CANopen communication.............44

7.1 CANopen setting.............44

7.2 CANopen Protocol...........46

7.2.1 SDO Introduction.............47

7.2.1.1 Upload SDO Protocol......47

7.2.1.2 Download SDO Protocol..49

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 3

7.2.1.3 Abort SDO Transfer Protocol

....................................... 52

7.2.2 PDO Introduction............ 55

7.2.2.1 PDO COB-ID Parameters55

7.2.2.2 Transmission Type.......... 56

7.2.2.3 PDO Communication Rule

....................................... 57

7.2.3 NMT Introduction............ 59

7.2.3.1 Module Control Protocol . 59

7.2.3.2 Error Control Protocol..... 61

7.2.4 Special Functions for

PM-4324-CPS.................62

7.2.4.1 Power Meter Data Table..62

7.2.5 Object Dictionary of

PM-4324-CPS.................64

7.2.5.1 Communication Profile Area

........................................64

7.2.5.2 Manufacturer Specific

Profile Area .....................71

Appendix: Questions & Answers.............77

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 4

Chapter 1 Introduction

1.1. PM-4324 introduction

ICP DAS offers PM-4324 family in a full range of Single-phase and Three-phase smart

power meters for power monitoring. The products offer a rich feature set combined with

easy-to-integrate communications.

With its high accuracy (<0.5%, PF=1), the PM-4324 series products can be applied both

on low voltage primary side and/or medium/high voltage secondary side and enable the

users to obtain in real time the reliable and accurate energy consumption readings from

the monitored equipments while in operation. These compact size and cost effective

Power Meters are equipped with revolutionary wired clip-on CT (various types support

input current up to 400A) and standard Modbus communication RS-485 protocol for

easy deployment. It works with input voltages ranging 10V ~ 500V, supporting a wide

range of applications.

Features：

True RMS Power Measurements

Energy Analysis for 3P4W-3CT, 3P3W-2CT, 3P3W-3CT, 1P2W-1CT, 1P3W-2CT

Current Measurements Up to 400 A with Different CT Ratio

Voltage Measurements Up to 500 V

Clip-on CT for Easy Installation

W Accuracy Better than 0.5% (PF=1)

Supports RS-485, Ethernet Interface

Supports Modbus RTU, Modbus TCP protocols.

Supports 2-Power Relay Output (Form A)

Total Harmonic Distortion (THD)

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 5

1.2. Caution

1.2.1.Danger

The meter contains hazardous voltages, and should never be disassembled. Failing to

follow this practice will result in serious injury or death. Any work on or near energized

meters, meter sockets, or other metering equipment could induce a danger of electrical

shock. It is strongly recommended that all work should be performed only by qualified

industrial electricians and metering specialist. ICP DAS assumes no responsibility if

your electrical installer does not follow the appropriate national and local electrical

codes.

1.3. Warning

ICP DAS assumes no liability for any damage resulting from the use of this product. ICP

DAS reserves the right to change this manual at any time without notice. The

information furnished by ICP DAS is believed to be accurate and reliable. However, no

responsibility is assumed by ICP DAS for its use, not for any infringements of patents or

other rights of third parties resulting from its use.

1.4. Product Warranty & Customer Support

ICP DAS warrants all products free from defects in material and workmanship for a

period of one year from the date of shipping. During the warranty period, we will, at our

position, either repair or replace any product that proves to be defective. To report any

defect, please contact ：+886-3- 597-3366 or [email protected].

Please have the model, serial number and a detailed problem description available

when you call. If the problem concerns a particular reading, please have all meter

readings available. When returning any merchandise to ICP DAS, a return SN. is

required.

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 6

1.4.1.Limitation of Warranty

This warranty does not apply to defects resulting from unauthorized modification,

misuse, or use for reason other than electrical power monitoring. The supplied meter is

not a user-serviceable product.

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 7

Chapter 2 Specifications

2.1 Specifications

Model

PM-4324

PM-4324-MTCP

PM-4324-CPS

AC Power Measurement

Wiring

1P2W-1CT, 1P3W-2CT, 3P3W-2CT, 3P3W-3CT and 3P4W-3CT

Measurement Voltage

10 ~ 500 V (CAT III)

Measurement Current

CT Φ10 mm (60 A); CTΦ16 mm (100 A); CTΦ24 mm (200 A);

CTΦ36m (300 A); CTΦ36m (400 A)

Measurement Frequency

50-60 Hz

W Accuracy

Better than 0.5% (PF:1)

Starting Current

>0.03A ( 60A ), >0.05A (100A ), >0.09A( 200A )

Power Parameter

Measurement

True RMS voltage (Vrms), True RMS current (Irms), Active Power (kW), Active Energy

(kWh), Apparent Power (kVA), Apparent Energy (kVAh),

Reactive Power (kVAR), Reactive Energy (kVARh), Power Factor (PF), Frequency(Hz)

Data Update Rate

1 Second

Communication

RS-485

Protocol

Modbus-RTU

-

Baud rate

9600,19200 (default), 38400,

115200; DIP Switch Selectable

-

Data

format

N,8,1 (default); N,8,2; E,8,1; E,8,2;

O,8,1; O,8,2

Isolation

3000 VDC

-

Bias

Resistor

No (Usually supplied by the

RS-485 Master. Alternatively, add

a tM-SG4 or SG-785)

Ethernet

Protocol

-

Modbus TCP

CANoepn

Protocol

CANopen

Alarm Output

Power Relay

Form A (Normal Open) x 2; Relay Contact Voltage Range: 5 A@ 250 VAC (47 ~ 63Hz),

5 A @ 30 VDC

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 8

Field Wiring Terminal Markings:

3.81mm (For Measurement Current and Communication): Use Copper Conductors Only,

wires range 16-26 AWG, torque value 3.0 lb-in.

5.08mm (For Measurement Voltage, Aux Power and Alarm Output):

Use Copper Conductors Only, wires range 12-24 AWG, torque value 7.0 lb-in.

7.62mm: Use Copper Conductors Only, wires range 12-24 AWG, torque value 4.5 lb-in.

Aux Power

Input Range

+100 ~ +240 VAC

Power Consumption

6 W

Dimensions (W x L x H)

237 mm x 52 mm x 134 mm

Environment

Operating Temperature

-20 ~ +70 °C

Storage Temperature

-25 ~ +80 °C

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 9

2.2 Naming Rules

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 10

Chapter 3 Installation

3.1 Inspection

The instrument is no longer safe when,

a) Shows clear signs of damage

b) Does not work

c) Long storage under extreme conditions

d) Damage during shipment

3.2 Safety

Please use the soft dry clothes to clean the instrument.

Please do not use any chemical or detergent or volatile solvents to clean the instrument,

in order to avoid any possibility of the cover damage.

3.2.1 Dimension and Latch

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 11

Products come with external split type clip-on CT’s. Disconnect the CT’s or use

other CT’s is highly prohibited.

Please read this operation manual carefully before using.

Please re-confirm the measure position.

PM-4324 series can be installed as rail mounting mode or embedded, no need to

drill a hole or screw to fix it (rail mounting width can up to the length of 35 mm).

Meter auxiliary power is +100 ~ +240 VAC.

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 12

3.2.2 Mounting and Dismounting

Mounting

Assembly: Place the PM-4324 on the DIN-Rail. Push the front of the PM-4324

toward the mounting surface until it audibly snaps into place.

Dismantling: Pull out the latch and then remove the PM-4324 from the DIN-Rail.

Wire Disconnection

1. Open the CT clip to detach the CT, do not remove the CT terminal lines if

possible

Note: if you need to remove the terminal lines, always detach the CT before

removing the CT terminal lines. Otherwise the CT may develop open-circuit

secondary voltages which may be hazardous to personnel or damaging to the

CT or equipment connected in the secondary circuit.

2. Disconnect the voltage input wires from terminals and wrap the wire tips with

plastic tape.

3. Disconnect the communication wires from terminal.

4. Disconnect the auxiliary power from terminal and wrap the wire tip with plastic

tape.

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 13

3.2.3 CT’s installation steps

At the bottom of the CT, there is a

“K→L”mark.

Open the CT clip.

Make sure the power current

direction follow the “K→L”mark on

the CT and then close the CT clip.

Installation steps finished.

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 14

Chapter 4 Wiring Diagrams

4.1 Connection

Please firstly check the current input terminal, and then in white black, white black,

white black wire sequences (CT1-K, CT1-L, CT2-K, CT2-L, CT3-K, CT3-L). Then

connect the CT’s, and close the CT clip. Make sure the arrow direction sign on CT’s

follows current flow direction（K→L）

Note: it must be in the same direction.

Connect the voltage input terminal N C BA. for PM-4324, in the three phase order

as follows on N C B A.

Attention please!! For 3P3W-2CT, connect in N C A phase sequence, do not

connect phase B (Check the diagram).

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 15

Voltage Input

1. PM-4324 series: Input Voltage up to 500V.

For any higher Input Voltage large than 500V, please add the PT (power transformer), and Change PT

RATIO setup.

2. Confirm the RST (ABC) phase sequence.

Current Input

1. The external CT’s are fragile, please handle with care.

2. The current input of PM-4324 series is in mArange. Only the ex-factory attached CT’s can be used.

The other CT’s, for example, from panel will damage the instrument due to its large current (around

5A)

3. When more than one smart meter (PM-4324 series) are installed, please do not disconnect the CT

with its original meter and mix use with each other. Since each set of smart meter (PM-4324 series)

and its attached split type clip-on CT are calibrated set by set. The mix use may cause wrong

measurements.

4. To install CT’s correctly, please ensure the CT lines sequences is right before clip the CT’s onto the

power cable of the monitoring equipment. (Detail will be found in next section)

5. When measuring the current, the secondary circuit of a CT should never be

opened when a load is passing through its primary. Make sure you always open

the CT clip to detach the CT before removing the terminal lines. Otherwise, it will cause severe

injury.

6. Please handle with extra care, especially when the operation space of CT’s is limited.

7. The current direction must follow K-L marked on CT’s.

8. Please select the right size CT’s for different size of monitoring equipment cables:

power cable diameter ＜Φ10 use 60A CT，Φ10～Φ16 use 100A CT，Φ16～Φ24 use 200A CT,

，Φ36 use 300A CT，Φ36 use 400A CT

9. The maximum current value cannot exceed the CT rating

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 16

4.2 Wiring

1P2W-1CT (PM-4324)

1P3W-2CT (PM-4324)

3P3W-2CT (PM-4324)

3P3W-3CT (PM-4324)

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 17

DIP switch: Wiring mode

SW 9

SW 10

3P3W-3CT

OFF

ON

3P4W-3CT (PM-4324)

DIP switch: Wiring mode

SW 9

SW 10

3P4W-3CT

ON

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 18

Chapter 5 Relay output & LED Indicator

5.1 Relay

Relay type

Power Relay, Form A (SPST N.O.)

Operating Voltage Range

250 VAC/30 VDC

Max. Load Current

5 A at 25 °C

Operate Time

6 ms

Release Time

3 ms

5.2 LED Indicator

The PM-4324 has 4 LED to indicate the unit power status, RS-485 communication, and

power data calculation.

RUN: Green, light up after RS-485 ready. LED will flash when the unit is processing

RS-485 communication.

PWR: Red, Power on LED always on.

DO0: Green. LED DO0 will light up, when DO0 is “ON”.

DO1: Green. LED DO1 will light up, when DO1 is “ON”.

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 19

Chapter 6 Modbus-RTU communication

6.1 RS-485 setting

Default setting for RS-485: 19200, n, 8, 1

DIP switch (SW1-SW6) is used for Modbus address setting, default is 1, i.e.

all OFF

For example: Modbus address is 10，find the table of DIP switch 1-6 is

ON, OFF, OFF, ON, OFF, OFF

6.1.1 SW1－SW6 setting

Setting Modbus-RTU address for communication (1-64)

Modbus Address

SW 1

SW 2

SW 3

SW 4

SW 5

SW 6

1

OFF

2

ON

OFF

3

OFF

ON

OFF

4

ON

OFF

5

OFF

ON

OFF

6

ON

OFF

ON

OFF

7

OFF

ON

OFF

8

ON

OFF

9

OFF

ON

OFF

10

ON

OFF

ON

OFF

11

OFF

ON

OFF

ON

OFF

12

ON

OFF

ON

OFF

13

OFF

ON

OFF

14

ON

OFF

ON

OFF

15

OFF

ON

OFF

16

ON

OFF

17

OFF

ON

OFF

18

ON

OFF

ON

OFF

19

OFF

ON

OFF

ON

OFF

20

ON

OFF

ON

OFF

21

OFF

ON

OFF

ON

OFF

22

ON

OFF

ON

OFF

ON

OFF

23

OFF

ON

OFF

ON

OFF

24

ON

OFF

ON

OFF

25

OFF

ON

OFF

26

ON

OFF

ON

OFF

27

OFF

ON

OFF

ON

OFF

PM-4324 User’s Manual v1.03 Last Revised: Feb. 2021 Page: 20

28

ON

OFF

ON

OFF

29

OFF

ON

OFF

30

ON

OFF

ON

OFF

31

OFF

ON

OFF

32

ON

OFF

33

OFF

ON

34

ON

OFF

ON

35

OFF

ON

OFF

ON

36

ON

OFF

ON

37

OFF

ON

OFF

ON

38

ON

OFF

ON

OFF

ON

39

OFF

ON

OFF

ON

40

ON

OFF

ON

41

OFF

ON

OFF

ON

42

ON

OFF

ON

OFF

ON

43

OFF

ON

OFF

ON

OFF

ON

44

ON

OFF

ON

OFF

ON

45

OFF

ON

OFF

ON

46

ON

OFF

ON

OFF

ON

47

OFF

ON

OFF

ON

48

ON

OFF

ON

49

OFF

ON

50

ON

OFF

ON

51

OFF

ON

OFF

ON

52

ON

OFF

ON

53

OFF

ON

OFF

ON

54

ON

OFF

ON

OFF

ON

55

OFF

ON

OFF

ON

56

ON

OFF

ON

57

OFF

ON

58

ON

OFF

ON

59

OFF

ON

OFF

ON

60

ON

OFF

ON

61

OFF

ON

62

ON

OFF

ON

63

OFF

ON

64

ON

ICP DAS USA PM-4324-400P-MTCP User manual

Popular Measuring Instrument manuals by other brands