ICP DAS USA PMD-2201 User manual

Copyright © 2016 ICP DAS Co., Ltd. All Rights Reserved E-mail: [e-mail]
1
PMD Quick Start
v1.3, Sep 2019
Supported Models
PMD-2201
PMD-2206
PMD-4201
PMD-4206
Technical Support
PMD User Manual and Firmware:
http://pmms.icpdas.com/en/download.html
ftp://ftp.icpdas.com/pub/cd/pmd_cd/
PMD Official Website:
PMD-2201: http://pmms.icpdas.com/en/PMD_2201.html
PMD-4201: http://pmms.icpdas.com/en/PMD_4201.html
PMD-2206: http://pmms.icpdas.com/en/PMD_2206.html
PMD-4206: http://pmms.icpdas.com/en/PMD_4206.html
What’s in the box?
The package includes the following items:
Power Meter Concentrator microSD card Screw Driver (1C016)
(PMD)
Cable * 2
(CA-090910-A)
Panel Clip * 4
M4 x 30L Screw * 4

Copyright © 2016 ICP DAS Co., Ltd. All Rights Reserved E-mail: [e-mail]
2
1 Mounting the Hardware
The PMD can be mounted on a panel of maximum thickness 5 mm.
Adequate access space can be available at the rear of the instrument panel
for wiring and servicing purposes.
To ensure proper ventilation for your PMD,
leave a minimum of 50 mm space between the top
and bottom edges of the PMD and the enclosure
panels.
1) Prepare the panel and cut the hole to the
specified size. The table below shows the
dimension of the panel cut-out of PMD.
Models
Depth
PMD-220x
44 mm
PMD-420x
54 mm
Models
Panel Cut-Out (Width x Height)
PMD-220x
197 mm x 133 mm, + 1 mm
PMD-420x
277 mm x 215 mm, + 1 mm

Copyright © 2016 ICP DAS Co., Ltd. All Rights Reserved E-mail: [e-mail]
3
2) Attach the PMD to the cut-out
hole.
3) Insert the panel
mounting clips into the
upper and lower
ventilation holes.
4) Screw the panel mounting
clips to the panel.
Recommended Screw Torque: 3.4 ~ 4.5 kgf-cm.

Copyright © 2016 ICP DAS Co., Ltd. All Rights Reserved E-mail: [e-mail]
4
2 Configuring the boot mode
Before starting PMD at the first time, be sure that the rotary switch is
placed in the “0” position.
3 Connect to PC, Network and Power
The PMD is equipped with an RJ-45 Ethernet port for connection to an
Ethernet hub/switch and PC. You can also link directly the PMD to PC
with an Ethernet cable.
PMD
The rotary switch must be placed in the "0" position

Copyright © 2016 ICP DAS Co., Ltd. All Rights Reserved E-mail: [e-mail]
5
4 Assign a New IP to PMD
The PMD is an Ethernet controller, which comes with a default IP
setting. The factory default IP settings of LAN1 are as follows:
Item
Default
IPAddress
192.168.255.1
Subnet mask
255.255.0.0
Gateway
192.168.0.1
DNS Server
8.8.8.8 (Default: Google DNS Server)
The user can modify the Network setting of PMD by two interfaces (local
side display interface and remote side Web page interface).
The Network setting steps of PMD are as below:
1. Network setting by Local Side Display Interface
Step1:Login PMD as the Administrator. Click the “System Setting” button.
Step2:Click the “Network Setting” on the “System Setting” menu.
Step3:Modify the PMD network setting to fit current network environment.

Copyright © 2016 ICP DAS Co., Ltd. All Rights Reserved E-mail: [e-mail]
6
Step4:Clicking on the “Save” button to save the setting.
Now you can use the Browser to connect to the PMD’s IP address
to open the Web page of PMD.
2. Network setting by Remote Side Web Page Interface
Step1: Change the PC’s IP setting as following.
IP: 192.168.255.10
Subnet mask: 255.255.0.0
Gateway address: 192.168.0.1
Step2: Make sure the PC and PMD(LAN1) is connecting through Ethernet.
Step3: Open a PC side browser, and type in the URL address
(http://192.168.255.1) of the PMD to connect the Web Server in
PMD.
Step4: Use default Administrator password “Admin” to login the system.
Step5: Please follow the sequence【System Setting】【Network Setting】
【Network Setting(LAN1)】to change the IP setting of PMD.
Step6: After complete the IP setting, please save it, and then the new IP
setting will take effect.

Copyright © 2016 ICP DAS Co., Ltd. All Rights Reserved E-mail: [e-mail]
7
5 Go to PMD Web Site for Power
Management
Please follow the steps below to build a power monitoring and
management applications with ICP DAS PMD & Power Meter.
Step 1: Open a browser, and type in the URL address of the PMD
Open a browser and type in the URL address(The new IP setting) of
the PMD in the address bar. Make sure the IP address is accurate.
Step 2: Get on the PMD web site
Get on the PMD web site. Complete the PMD setting in the order:
【Login】【System Setting】【Meter / Module Setting】【Rule
Setting】【Save】for a power monitoring and management
application.
Step 3: For more detail information, please refer to PMD User
Manual