ICP DAS USA iWSN-9601 Series User manual

P1
iWSN-9601 Series Quick Start
v1.0, Sep. 2023
Packing List
In addition to this guide, the package includes the following items
iWSN-9601
Series
Screw
driver
Split
Core CT
4 M4*16L
Mounting Screws
Model Name
Split Core CTs
iWSN-9601-□□□-ME-IP33
(□□□: 160, 240, 360)
6
iWSN-9601-PCP-ME-IP33
None
Technical Support
[e-mail]
www.icpdas.com
Resources
How to search for drivers, manuals and spec
information on ICP DAS website.
For Mobile Website
For Desktop Website
Model Name
Model Name

P2
1. Appearance
No.
Descriptions
1
LED panel cover.
The LEDs statuses are shown here.
Loosening two screws and opening the
cover can configure the module by the
DIP switches and trigger button.
2
The screws for LED panel cover.
3
Connector protector.
Loosening two screws and open the
protector can wire the CTs and voltage
input cables into the module.
4
The screws for connector protector.
5
The connector for CT wiring
6
The connector for voltage input wiring
2. LED indicators
The meanings of the LED actions are described as
follows.
No.
Descriptions
Color
1
Power indicator (PWR)
Red
2
RF data transmission indicator (Tx)
Green
3
Error status indicator (Err)
Yellow
LED Actions
Descriptions
Red LED is always OFF
No power
Red LED is always ON
Working power is given
Both Green and Yellow LEDs are ON
Module is initializing
Both Green and Yellow flash 5 times per
second
Detecting hardware errors during
initializing.
Green LED is always ON, Yellow LED flashes
quickly and periodically.
Invalid Node ID (Node ID 0 is
reserved, and can’t be used)
Green and yellow LEDs interactively flash 3
times afterwards turned ON simultaneously.
Detecting 50Hz AC frequency. The
60Hz won’t have any indication.
Green and Yellow LEDs are OFF, afterwards
Green LED flashes depended on the Tx duty
or while receiving an RF command.
The module has finished the
initialization, and starts to work.
Yellow LED flashes twice per second
Detecting errors during operating.
2
1
3
4
5
1
2
3
6

P3
3. DIP switch & trigger button
No.
Definitions
Descriptions
1
L Switch for configuring
the RF channel, Tx period
and AC wiring types.
2
R Switch for configuring
the Node ID, RF group ID
and the PA function.
3
Trigger button for forcing
to transmit data once.
Holding it 5 seconds will
reset the module.
The Configurations and descriptions of L Switch and R Switch are as follows.
Items
Descriptions
RF Ch
■：Up
□：Down
Ch
Pin
Ch
Pin
1
2
3
4
1
2
3
4
0
□
□
□
□
8
□
□
□
■
1
■
□
□
□
9
■
□
□
■
2
□
■
□
□
A
□
■
□
■
3
■
■
□
□
B
■
■
□
■
4
□
□
■
□
C
□
□
■
■
5
■
□
■
□
D
■
□
■
■
6
□
■
■
□
E
□
■
■
■
7
■
■
■
□
F
■
■
■
■
TX Duty
■：Up
□：Down
Period
Pin
5
6
1 sec.
□
□
10 sec.
■
□
30 sec.
□
■
60 sec.
■
■
F1/F2
N/A
3
1
2

P4
Wiring Types
Wiring Methods
Single Phase
2 Wire 1CT
Items
Descriptions
Node ID
(NID)
■：Up
□：Down
NID
Pin
NID
Pin
1
2
3
4
5
1
2
3
4
5
0
□
□
□
□
□
16
□
□
□
□
■
1
■
□
□
□
□
17
■
□
□
□
■
2
□
■
□
□
□
18
□
■
□
□
■
3
■
■
□
□
□
19
■
■
□
□
■
4
□
□
■
□
□
20
□
□
■
□
■
5
■
□
■
□
□
21
■
□
■
□
■
6
□
■
■
□
□
22
□
■
■
□
■
7
■
■
■
□
□
23
■
■
■
□
■
8
□
□
□
■
□
24
□
□
□
■
■
9
■
□
□
■
□
25
■
□
□
■
■
10
□
■
□
■
□
26
□
■
□
■
■
11
■
■
□
■
□
27
■
■
□
■
■
12
□
□
■
■
□
28
□
□
■
■
■
13
■
□
■
■
□
29
■
□
■
■
■
14
□
■
■
■
□
30
□
■
■
■
■
15
■
■
■
■
□
31
■
■
■
■
■
Group ID
■：Up
□：Down
RF Group ID
Pin
6
7
0
□
□
1
■
□
2
□
■
3
■
■
PA
■：Up
□：Down
PA Function
Pin 8
Enable (only for factory test)
■
Disable
□

P5
4. Pin assignments
5. CT installation
KL on the bottom of split CT
indicates the current direction. If
the real current direction is
different from the mark KL, the
negative value of power factor
will be obtained. After finishing
the CT installation, please confirm
if the safety lock buckle of the CT
is locked correctly.
CT input connector. CT_0/1/2/3/4/5 is used for 6 single-phase current
measurements. The terminal labeled W is for connection to the CT white (or
red) wire and the terminal labeled B is for connection to the CT black wire.
AC voltage input connector. AC+ and AC- are connected to the L-phase and
N-phase of the single-phase power supply. Normally, GND must be shorted
to AC-. If AC+ and AC- are used in the three-phase voltages (for line voltage
measurement), GND can be connected to the N-phase in order to minimize
the voltage measurement error. If the three-phase power supply does not
have an N-phase, GND can be connected to FG or shorted to AC-.
Translated with DeepL
When connecting the wire to CT
and voltage input connectors,
the twin cord end terminal must
be used, and the dimensions
are recommended as the table.
Connector Type
L (mm)
CT
6 ~ 7
Voltage
7

P6
Model Name
Type and Rating
Size A
Size B
iWSN-9601-PCT-ME-IP33
Split CT, Max. 400 A
-
-
iWSN-9601-160-ME-IP33
Split CT, 100 A
15.7
29
iWSN-9601-240-ME-IP33
Split CT, 200 A
23.6
45.2
iWSN-9601-360-ME-IP33
Split CT, 400 A
35.7
57.5
6. Module Installation
7. Operations
Users can prepare a PC and iWSN-200U (or iWSN-200E) for data collection
of iWSN-9601 series modules.
1. Configure the RF channel and Group ID of iWSN-200U/E to the same
configuration of the iWSN-9601 series modules.
2. Set the Node ID (1 ~ 31),
wiring type and Tx duty, and
finish the wiring connection.
The Node ID must be
unique in a sub-network
(the same RF channel and
group ID). The architecture
might look like as the
right-hand-side figure.
The iWSN-9601 series provide the
IP33 rating enclosure which can effectively
prevent the modules from the influence of
the fire sprinkler systems. Users need to
install the module vertically and screws up
the LED panel cover and connector
protector properly to guarantee the IP33
rating performance.
The iWSN-9601 series modules can only be used
with the specific CTs. Only the model name
iWSN-9601-PCT-ME-IP33 doesn’t include CTs.
Please check the accessories of the product
website or contact to the ICP DAS distributor to
purchase the CTs for this model if necessary.
Different model name provides different size of
CTs, they are described below.
Unit: mm
Vertical
Horizontal

P7
3. Turn ON the iWSN-200U/E and iWSN-9601 series module to start the data
collection. The RF_Rx LED of the iWSN-200U/E flashing once indicates the
iWSN-200U/E has received one message from the iWSN-9601 series module.
4. Users can use the PC with iWSN Utility to get the data or directly access the
iWSN-200U/E registers via Modbus RTU/TCP protocol, about the definitions
of the Modbus register please refer to the iWSN-200U/E user manual.
8. Product Specifications
Model Name
iWSN-9601-PCT-ME-IP33
iWSN-9601-160-ME-IP33
iWSN-9601-240-ME-IP33
iWSN-9601-360-ME-IP33
EMS Protection
EFT(IEC 61000-4-4)
+/- 500 V
ESD(IEC 61000-4-2)
+/- 4 kV Contact
LED Indicators
Status
1 for Power, 1 for Tx, and 1 for Error
AC Power Measurement
Wiring
1P2W-1CT
Loops
6
Input Voltage
Single phase 2 wire x 1, 58 - 277 VAC
Input Current
Max. 400 A
-160: Max. 100 A
-240: Max. 200 A
-360: Max. 400 A
Input Frequency
50/60 Hz
Wh Accuracy
(PF=1)
Better than 2%
Better than 1%
Power Parameter
Measurement
True RMS voltage (Vrms), True RMS current (Irms), Active
Power (kW), Active Energy (kWh), Power Factor (PF),
Frequency, and timestamp (YYYY/MM/DD HH:MM:SS)
Categories
CAT II
Data Update Rate
1, 10, 30, or 60 seconds
Antenna
Type
Built-in Omni-directional antenna
1. The flash of RF_Rx LED indicates
the iWSN-200U/E gets the data
from iWSN-9601 series module

P8
Power
Consumption
3 W
Input Type
Single phase 58 - 277 VAC
CT
Includes CTs
0 (*Note)
6
CT Type
Split core CT
Max. Current
Depended on the selection
(Max. 400 A)
-160: Max. 100 A
-240: Max. 200 A
-360: Max. 400 A
Inside Diameter
Depended on the selection
(Max. 36 mm)
-160: 16 mm
-240: 24 mm
-360: 36 mm
Leading Cable
8 m
RF
Channels
0 ~ 15
Group ID
0 ~ 3
Radio Frequency
433.1000 ~ 434.6000 MHz
Transmission
Power
9±1 dBm (Typical)
Transmission
Distance (LoS)
100 m
Node ID
1 ~ 31
Working Duty
1, 10, 30, or 60 seconds
Mechanical
Dimensions (mm)
85 x 184 x 47 (W x L x H)
Installation
Wall-mount
Ingress Protection
Rating
IP33
Environment
Operating Temper.
-30 °C ~ +50 °C
Storage Temper.
-40 °C ~ +55 °C
Humidity
10 ~ 90% RH, Non-condensing
Altitude
Max. 2000 m
Note: Please check the accessories of the product website or contact to the ICP
DAS distributor to purchase the CTs for this model if necessary.

P9
Caution
1. Danger
The meter contains hazardous voltages, and should never be disassembled.
Failing to follow this practice will result in serious injury or death. Any work on
or near energized meters, meter sockets, or other metering equipment could
induce a danger of electrical shock. It is strongly recommended that all work
should be performed only by qualified industrial electricians and metering
specialist. ICP DAS assumes no responsibility if your electrical installer does not
follow the appropriate national and local electrical codes.
2. Warning
ICP DAS assumes no liability for any damage resulting from the use of this
product. ICP DAS reserves the right to change this manual at any time without
notice. The information furnished by ICP DAS is believed to be accurate and
reliable. However, no responsibility is assumed by ICP DAS for its use, not for
any infringements of patents or other rights of third parties resulting from its
use.
3. Product Warranty & Customer Support
ICP DAS warrants all products free from defects in material and
workmanship for a period of one year from the date of shipping. During the
warranty period, we will, at our position, either repair or replace any product
that proves to be defective. To report any defect, please contact ：+886-3-
597-3366 or servic[email protected]. Please have the model name, serial number
and a detailed problem description available when you call. If the problem
concerns a particular reading, please have all meter readings available. When
returning any merchandise to ICP DAS, a return SN. is required.