Icron USB 2.0 Ranger 2312 User manual

USB 2.0 Ranger®2 312
2-port USB 2.0 100m CAT 5e/6/7 Extender System
with Flexible Power
User Guide

Thank you for purchasing the USB 2.0 Ranger® 2312.
Please read this guide thoroughly.
This document applies to, but is not limited to, Part Numbers: 00-00406, 00-00407, 00-00408, 00-00409 and
00-00410.
FCC Radio Frequency Interference Statement Warning
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received
including interference that may cause undesired operation.
CE Statement
We, Icron Technologies Corporation, declare under our sole responsibility that the USB 2.0 Ranger 2312, to
which this declaration relates, is in conformity with European Standard EN 55022, EN 61000, and EN 55024.
IC Statement
This Class B digital apparatus complies with Canadian ICES-003.
WEEE Statement
The European Union has established regulations for the collection and recycling of all waste electrical
and electronic equipment (WEEE). Implementation of WEEE regulations may vary slightly by individual EU
member states. Please check with your local and state government guidelines for safe disposal and recycling
or contact your national WEEE recycling agency for more information.
Product Operation and Storage
Please read and follow all instructions provided with this product, and operate for intended use only.
Do not attempt to open the product casing as this may cause damage and will void warranty. Use only
the power supply provided with this product.When not in use, product should be stored in a dry location
between -20°C and 70°C.
©2017 All rights reserved.
Document # 90-01524-A02

Contents
Introduction........................................................................................................................ 3
USB 2.0 Ranger 2312 Product Contents.................................................................................................................................... 3
Requirements.................................................................................................................................................................................... 3
Features............................................................................................................................................................................................... 3
The LEX Unit ...................................................................................................................................................................................... 4
The REX Unit...................................................................................................................................................................................... 5
Installation Guide ............................................................................................................... 6
Preparing for Installation............................................................................................................................................................... 6
Installing the LEX ............................................................................................................................................................................. 6
Installing the REX............................................................................................................................................................................. 6
Installing Flexible Power ............................................................................................................................................................... 6
Connecting the LEX to the REX................................................................................................................................................... 7
Connecting a USB Device ............................................................................................................................................................. 7
Checking the Installation .............................................................................................................................................................. 8
Compatibility..................................................................................................................................................................................... 8
Optional USB Extender Mounting Options ...................................................................... 9
Option 1: USB Extender Mounting Kit...................................................................................................................................... 9
Option 2: USB Extender Direct Surface Mounting ............................................................................................................... 10
Option 3: Cable-Tie Mounting..................................................................................................................................................... 10
Troubleshooting ................................................................................................................. 11
Warranty information ........................................................................................................ 13
Obtaining Warranty Service......................................................................................................................................................... 13
Contacting Technical Support ........................................................................................... 14
Technical Glossary .............................................................................................................. 15
Specifications...................................................................................................................... 16

Introduction
This guide provides product information for the USB 2.0 Ranger® 2312, installation instructions and
troubleshooting guidelines. The instructions in this guide assume a general knowledge of computer
installation procedures, familiarity with cabling requirements and some understanding of USB devices.
Notes provide additional information that could be useful.
Caution symbols are followed by very important information about an operational requirement.
USB 2.0 Ranger 2312 Product Contents
Your Ranger 2312 is packaged with:
• LEX (Local Extender)
• REX (Remote Extender)
• USB 2.0 Cable
• International AC Power Adapter
• Country Specific Power Cord
• Quick Start Guide
The Ranger 2312 features flexible power, allowing the installer to connect the supplied 24V, 1A power adapter to either
the LEX or REX unit for normal extension system operation. Please note, when powering at the LEX, take care not to plug
the remote side of the CAT 5e/6/7 link cable directly into equipment other than the REX to avoid possible damage as
flexible power is different from Power over Ethernet (PoE) and will only properly power the REX.
Requirements
To complete the installation, you will also require the following items that are not included with the product:
• USB 1.1 or 2.0 compatible computer (host computer) with a USB compliant operating system
• USB 1.1 or 2.0 compatible device(s)
• CAT 5e/6/7 solid core Unshielded Twisted Pair (UTP) cable with two RJ45 connectors (if using surface
cabling), or CAT 5e/6/7 cabling with two information outlets and two CAT 5e/6/7 patch cords with
RJ45 connectors (if using premise cabling)
Features
The Ranger 2312 incorporates ExtremeUSB® technology, enabling users to extend USB beyond the standard
5m cable limit for USB 2.0 peripheral devices.The Ranger 2312 extender system is composed of two
individual units, the LEX and the REX, and has the following key features:
• USB device(s) can be located up to 100 meters (330 feet) from the computer
• Support for new USB 3.0 host controllers and devices (up to 480 Mbps)
• Support for all device USB types
The Ranger 2312 includes the ExtremeUSB® suite of features:
• Transparent USB extension
• True plug and play; no software drivers required
• Works with all major operating systems:Windows®, macOS™and Linux®
note
note
3

The LEX Unit
The LEX unit connects to the computer using a standard USB cable (included). Power for the LEX is provided
by the host computer. Power for the REX is provided by the 24V AC adapter connected at either the LEX or
REX.The LEX delivers power over the CAT 5e/6/7 extension link to the REX when the included power supply is
connected to the LEX.
ITEM TYPE DESCRIPTION
1 Mode Reserved for manufacturer use.
2 Config Port Reserved for manufacturer use.
3 Power LED (Blue) LED turns on when power is supplied.
LED is off when no power is supplied by the host computer.
4 Link LED (Green) Indicates a valid ExtremeUSB link is established between the LEX and REX
units.
LED turns on when link between the LEX and REX units is established.
LED is off when there is no link between the LEX and REX units.
LED is slow blinking when the unit is attempting to establish a link.
5 Host LED (Green) Indicates that the extender system is properly enumerated on the host
computer. LED blinks when the extender system is in a suspended state.
6 Activity LED
(Amber)
Indicates data transmission is occurring between the LEX and REX units.
LED blinks intermittently with or without a USB device connected.
When the LEX and REX units are in suspend mode, the LED is off.
7 Power Port Connects to the AC power supply.
8 Link Port (RJ45) Accepts RJ45 connector for CAT 5e/6/7 cabling to connect the LEX to the
REX.
9 USB Host Port Used to connect the LEX to the host computer.
Accepts USB Type B connector.
4
Front View
Rear View

The REX Unit
The REX unit provides two USB Type A ports for connecting standard USB devices allowing up to 1 Amp per
USB port, or 1.5 Amps total when both ports are used concurrently. Additional devices may be connected by
attaching USB hubs to the REX.The REX is powered either directly by the included power supply, or via the
CAT 5e/6/7 link extension cable from the LEX.
ITEM TYPE DESCRIPTION
1 USB Device Ports Accepts USB device(s) using Type A connectors.
2 Power LED (Blue) LED turns on when power is supplied.
3 Link LED (Green) Indicates a valid ExtremeUSB link is established between the LEX and REX
units.
LED turns on when link between LEX and REX units is established.
LED is off when there is no link between the LEX and REX units.
LED is slow blinking when the unit is attempting to establish a link.
4 Host LED (Green) Indicates that the extender system is properly enumerated on the host
computer. LED blinks when the extender system is in a suspended state.
5 Activity LED
(Amber)
Indicates data transmission is occurring between the LEX and REX units.
LED blinks intermittently with or without a USB device connected.
When the LEX and REX units are in suspend mode, the LED is off.
6 Power Port Connects to the AC power supply.
7 Link Port (RJ45) Accepts RJ45 connector for CAT 5e/6/7 cabling to connect the LEX to the
REX.
8 Config Port Reserved for manufacturer use.
9 Mode Reserved for manufacturer use.
5
Front View
Rear View

Installation Guide
LEX
Host Computer
REX
All USB Devices
Up to100m between extenders over CAT 5e/6/7
Power can be supplied to either LEX or REX
Preparing for Installation
Before you can install the Ranger 2312, you need to prepare your site:
1. Determine where the computer is to be located and set up the computer.
2. Determine where you want to locate the USB device(s).
3. If you are using surface cabling, the Ranger 2312 supports a maximum distance of 100m.
OR
If you are using premise cabling, ensure CAT 5e/6/7 cable is installed between the two locations,
with CAT 5e/6/7 information outlets located near both the computer and the USB device(s), and the
total length, including patch cords is no more than 100m.
Installing the LEX
1. Place the LEX near the computer.
2. Install the supplied USB cable between the LEX host port and a USB port on the host computer.
Installing the REX
1. Place the REX near the USB device(s) in the desired remote location.
Installing Flexible Power
1. Connect the 24V 1A supplied AC power adapter into the desired unit—either the LEX unit or REX
unit, based on your installation requirement.
The Ranger 2312 features flexible power, allowing the installer to connect the supplied 24V, 1A power adapter to
either the LEX or REX unit for normal extension system operation. Please note, when powering at the LEX, take care
not to plug the remote side of the CAT 5e/6/7 link cable directly into equipment other than the REX to avoid possible
damage as flexible power is different from Power over Ethernet (PoE) and will only properly power the REX.
6
Connect the provided power adapter to either the LEX or REX.
note

Connecting the LEX to the REX
To ensure proper operation, it is recommended that only solid core CAT 5e/6/7, Unshielded Twisted Pair (UTP) cabling
be used to connect the LEX to the REX.The cabling must have a straight-through conductor configuration with no
crossovers and must be terminated with 8 conductor RJ45 connectors at both ends.The combined length of any patch
cords using stranded conductors must not exceed 100m.
With Surface Cabling:
1. Plug one end of the CAT 5e/6/7 cabling (not included) into the Link port (RJ45) on the LEX.
2. Plug the other end of the CAT 5e/6/7 cabling into the Link port (RJ45) on the REX.
With Premise Cabling:
1. Plug one end of a CAT 5e/6/7 patch cord (not included) into the Link port (RJ45) on the LEX.
2. Plug the other end of the patch cord into the CAT 5e/6/7 information outlet near the host computer.
3. Plug one end of the second CAT 5e/6/7 patch cord (not included) into the Link port (RJ45) on the
REX.
4. Plug the other end of the second patch cord into the CAT 5e/6/7 information outlet near the USB
device.
Connecting a USB Device
1. Install any software required to operate the USB device(s). Refer to the documentation for the USB
device(s), as required.
2. Connect the USB device(s) to the device port on the REX.
3. Check that the device is detected and installed properly in the operating system.
7
note

Checking the Installation
1. Check that the Power, Activity, Link and Host LEDs on the LEX and REX units are on. If the Host or Link
LEDs are permanently off, then the cabling between the LEX and REX units may not be installed properly
or is defective.
2. For Windows users (XP, 7, 8, 8.1, 10), open Device Manager to confirm that the Ranger 2312 extender
system has been installed correctly. Expand the entry for Universal Serial Bus controllers by clicking the
“+”sign. If the extender system has been installed correctly, you should find it listed as a “Generic USB
Hub”.
To open Device Manager in Windows XP:
Right click“My Computer”then select: Properties >> Hardware tab >> Device Manager
To open Device Manager in Windows 7:
Open the Start Menu, right click on“Computer”then select: Manage >> Device Manager
To open Device Manager in Windows 8, 8.1 or 10:
Right click the Start Menu and then select: Device Manager
3. For macOS users, open the System Profiler to confirm that the Ranger 2312 extender system has installed
correctly. In the left hand column under Hardware, select“USB” and inspect the right hand panel. If the
extender has been installed correctly, you should find it listed as a“Hub”under the USB High-Speed Bus/
USB Bus.
To open System Profiler in macOS:
Open the Finder, select Applications, then open the Utilities folder and double click on the System Profiler icon.
4. If the Ranger 2312 extender system is not detected correctly or fails to detect, please consult the
Troubleshooting section in this guide.
Compatibility
The Ranger 2312 complies with USB 1.1 and USB 2.0 specifications governing the design of USB devices.
However, there is no guarantee that all USB devices will be compatible, as there are a number of different
factors that may impact the operation of USB devices over extended distances.
8
note
note
note
note

9
Optional USB Extender Mounting Options
The bottom of the Ranger 2312 enclosure features four convenient pre-drilled holes for optional direct
surface mounting and four mounting slots for easy cable-ties. Based on your requirements, choose from
three available mounting options:
1. USB Extender Mounting Kit
2. USB Extender Direct Surface Mounting
3. USB Extender Cable-Tie Mounting
Option 1: USB Extender Mounting Kit
Order Part #10-00535 USB Mounting Kit (2301/12) - Silver (Available for purchase separately)
1 kit required to mount per LEX or REX
Each kit includes:
• 2 mounting brackets
• 4 (M2.5) locking washers
• 4 (M2.5 x 7.0mm) Phillips pan head screws
• Mounting bracket installation guide (see diagram below)
Using a Phillips screwdriver, in the order as illustrated below, fasten and secure the provided screws, locking
washers and brackets into place.