ICW ELITE DOUBLE ARM User manual

ICWUSA.com, Inc.
If you have any questions, please call 1-800-558-4435
ELITE DOUBLE ARM
ELITE DOUBLE ARM INSTRUCTIONS - rev 11/01/2013 mf
page 1
DANGER!
1. Do not attempt to adjust your Elite arm until
everything you intend to mount to the arm is
mounted.
2. Arm must be completely horizontal (extended)
before adjusting the arm’s tension. Failure to do
so will damage the arm and void the warranty.
3. Never loosen or remove any of the shoulder bolts. Doing so
will cause the arm to immediately come apart with tremendous
force, and could cause serious injury.
4. If equipment requiring AC power is mounted to this unit, have a
certifi ed electrician inspect the installation.
5. Failure to install this unit according to these instructions will void
all ICW warranties. If installed incorrectly, ICW is not liable for any
damage or injury caused by the unit.
6. Do not use power tools to adjust arm tension. MUST be adjusted
by hand.
The Elite arm contains high
pressure gas springs. The
following cautions MUST be
observed to avoid serious injury.
ATTACH WALL
PLATE TO WALL
Locate stud and mark top
hole, drill 11/64 pilot hole
and insert #14 screw and
tighten slightly. Using a
level, mark lower hole
and drill pilot hole, insert
#14 screw and, with
unit level, tighten both
screws. ICW supplies
#14 wood screws. If
installing onto metal
studs, you will need
to replace with proper
metal stud fasteners.
ATTACH TO DESK
Drill a 3/8 hole through the horizontal
surface you intend to mount to. Screw
the 3/8 stud into your desk mount
as shown, the stud is found in your
hardware bag.
Push the 3/8 stud on desk mount
through the hole in the desk and slip
the large mounting washer over the
stud from underneath and secure in
place with the 3/8 nylock nut.
Detach the pole mount from arm using the provided
5mm hex key. Separate the two sections of the
pole mount using the provided 5/32 hex key. Place
around the pole you are mounting to and fi rmly
reassemble the pole mount.
ATTACH TO POLE

ICWUSA.com, Inc.
If you have any questions, please call 1-800-558-4435
ELITE DOUBLE ARM
ELITE DOUBLE ARM INSTRUCTIONS - rev 11/01/2013 mf
page 2
REMOVE ELITE
ARM COVERS
TOP COVERS:
Remove the
long arm cover
by unscrewing
the two 1/4”
long 6-32
fl athead screws
in the center of
the cover using
a philips head
screwdriver.
END COVERS:
Remove the
end covers by
unscrewing the two
3/4” long 10-24
fl athead screws
using a philips
head screwdriver.
CENTER COVER:
Remove the
center cover by
unscrewing the
four 3/4” long
10-24 fl athead
screws using
a philips head
screwdriver.
ATTACH ELITE ARM TO WALL MOUNT
Pass 3/8 bolt with bearing
assembly through wall
mount ear and into end
of Elite Arm. Secure Elite
Arm over wall mount
using split lock washer
and nylock nut with 9/16
wrench provided and
5mm hex key.
9/16 wrench
(provided)
5mm Black plastic beauty cap
Bearing
assembly
MANAGE CABLES THROUGH ARM
Extend the arm straight out and
lay all the cables for your monitor,
keyboard and mouse in the
channel on top of the arms. Lay cables evenly around
adjuster with wire loom
on each side.
Wire tie cables around
adjuster, securing the
cords and the wire loom.
Leave some slack.
Add provided wire clips,
weaving through wire loom
to secure cables.
NOTE: YOU MUST
LEAVE SOME SLACK IN
THE CABLES TO ALLOW
FOR ARM MOVEMENT.
Add wire clips to end
of arms as well.
ADJUST ROTATION LIMITS - WALL MOUNT
The rotation limits for
the arm are set by
placing the stop pins in
the hole corresponding
to where you want the
arm to stop. The stop
pin then collides with
the stop block on the
front of the wall mount
ear, stopping the arm.
The stop pins can be
removed and set by
hand.
Stop Pin
Stop Pin
Stop Block
IF YOU ORDERED THE ROTATION LIMITER ACCESSORY

ICWUSA.com, Inc.
If you have any questions, please call 1-800-558-4435
ELITE DOUBLE ARM
ELITE DOUBLE ARM INSTRUCTIONS - rev 11/01/2013 mf
page 3
ATTACH PARALINK KEYBOARD TRAY
Loosen knob to adjust Paralink.
Adjust horizontally for keyboard tray
and vertically for monitor. Tighten
knobs when in desired position.
Attach the keyboard tray
to the Keyboard Mount
using the supplied 5/16-
18 socket head screw.
ADJUST BALL VESA
TENSION & HEIGHT
Use the slider knob to
loosen the slider to adjust
the height of the monitor
on the Paralink.
Adjust the pivot tension
of the ball by gently and
evenly tightening or
loosening the four screws
on the back of the ball
VESA.
Slider Knob
Pivot tension
adjustment
screws
ATTACH VESA
TO MONITOR
Using a phillips
screw driver,
attach the VESA
plate to the back
of your LCD
monitor.
ADJUST
PARALINK TILT
Adjust Monitor to desired
position with ball VESA.
Tilt your monitor 50°
in any direction. Adjust
your monitor between
portrait and landscape
by rotating ball VESA.
Adjust monitor depth
by moving the paralink
forward or back then
tighting the depth
adjustment knob.
Depth
Adjustment
Knob
ADJUST ELITE ARM RESISTANCE
Extend the Elite straight out
as shown before adjusting
the arms’ resistance. Be sure
all equipment is mounted on
the arm before adjusting.
Adjust the arm closest to
the monitor fi rst. Use the
T-handle provided to adjust
the arms’ resistance. Do not
use power tools to adjust.
ATTACH KEYBOARD TO MONITOR
Attach the Paralink
Keyboard Mount to
the Monitor Mount
by using the 3/8-16
screw and lock washer
provided
ATTACH ELITE
ARM COVERS
TOP COVERS:
Attach the long arm
cover by screwing the
two 1/4” long 6-32
fl athead screws in the
center of the cover
using a philips head
screwdriver.
END COVERS:
Attach the
end covers by
screwing the
two 3/4” long
10-24 fl athead
screws using
a philips head
screwdriver.
CENTER COVER:
Attach the center
cover by screwing
the four 3/4” long
10-24 fl athead
screws using
a philips head
screwdriver.
NOTE: DO NOT USE
POWER TOOLS TO ATTACH.
DO NOT OVER TIGHTEN.
IF COVER IS BEING
DISTORED, SCREW HAS
BEEN OVER-TIGHTENED