ICW Titan Elite User manual

Titan Elite Installation
DANGER!
1) Do not attempt to adjust your Elite arm un-
til everything you intend to mount to the arm is
mounted.
2) Arm must be completely horizontal (extended)
before adjusting the arm’s tension. Failure to do
so will damage the arm and void the warranty.
3) Never loosen or remove any
of the shoulder bolts. Doing so
will cause the arm to immedi-
ately come apart with tremen-
dous force, and could cause
serious injury.
4) If equipment requiring AC power is mounted
to this unit, have a certied electrician inspect the
installation.
5) Failure to install this unit according to these
instructions will void all ICW warranties. If in-
stalled incorrectly, ICW is not liable for any dam-
age or injury caused by the unit.
The Elite arm contains high
pressure gas springs. The fol-
lowing cautions MUST be ob-
served to avoid serious injury.
Shoulder bolt
1 Remove the ceiling mount from the box, and nd the 4 #14 wood screws in the hardware bag. Firmly
secure the ceiling mount to a solid stud in the ceiling using
the 4 provided screws and being sure the mount is level.
Loosen the set screw in the ceiling mount and thread the
extension pipe fully into the ceiling mount and retighten
the set screw.
2 Remove the long arm cover by unscrewing the (2) 6-32 athead screws using a Phillips head
screw driver.
3 Remove the end covers by unscrewing the (2) 10-24 athead screws using the 1/8” hex key.
4 Disassemble the upper arm using the provided socket wrench and 5mm hex key. Keep track of
all parts.
Slip the end
caps out of
the arm.
Do not disassemble these bearing packs.
3/8” Nylock,
split washer
and race
Ceiling mount
Extension pipe

5 Slip all cords through the upper arm.
6 Run the cords from the upper arm all the way through the cord channel on the lower arm.
10
Loosen set screw and
thread arm onto
ceiling mount, then
tighten set screw.
Set screw
Your Paralink
mount comes
with a universal
VESA that will
accommodate a
75mm or 100mm
monitor.
11
Attach your monitor to the VESA mount using
the 4mm screws in the hardware bag.
13
The Paralink allows horizontal adjustment of the
monitor. Unscrew knob to release, move monitor
in to desired position and tighten down knob
to lock.
14
Once your monitor is mounted, extend and adjust
the tension on the lower arm using the
T-handle adjustment wrench provided.
Thank you for your purchase of an ICW Titan Elite arm. Any questions? Please call 1-800-558-4435. Titan Elite PL Ceiling 5/26/10 JM
Adjustment port
Rotation
control knob
Bring cord from upper arm
to back of the lower arm rst.
Place cord through end frame
and over cable channel
7 Slide the end caps back into the arm, feeding the cord through the openings. Reassemble the
upper arm.
8 Replace the three covers on the lower arm, being
careful not to pinch the cords.
9 Feed the cords through the plastic bushing in the end covers. The plastic bushing can be removed,
opened and slipped over cord, if necessary.
Wrap excess cable outside of the arm. Tension
adjustment
hole
12 VESA Swivel Adapter allows 180° of
movement. If necessary to hold, tighten the
pivot screws.

A. Once the arm assembly is fixed to the ceiling
mount and adjusted to the neutral setting,
move the arm to it’s vertical position.
Long arm covers and end covers should
be removed.
A. Place Paralink up to base of arm and
insert stud.
B. Place flat washer, thrust bearing assembly,
second flat washer and lock washer on to stud
followed by the Nylock nut.
A. Using supplied socket wrench, spin
Paralink assembly until nut is finger tight
followed by an extra 1/4 turn.
A. Install end cover by reversing step 1.
1
Thrust Bearing Assembly
Flat Washer
Lock Washer
Flat Washer
Nylock Nut
PARALINK TO ELITE MOUNTING INSTRUCTIONS
2
3
4
092309V1