ICW ELITE 5220 User manual

ELITE 5220 BEARING REPLACEMENT - 05/02/16 pjm
ELITE 5220 FRONT BEARING REPLACEMENT
Page 1 of 2
DO NOT use power tools to assemble or
adjust the arm. Use hand tools ONLY.
IMPORTANT
•Do not attempt to adjust the Elite arm until all
components are mounted (monitor, keyboard, etc.)
•Arm must be completely horizontal (extended)
before adjusting the arm’s tension. Failure to do so will
damage the arm and void the warranty.
•NEVER loosen or remove any of the shoulder
bolts. Doing so will cause the arm to immediately
come apart with tremendous force, and could cause
serious injury.
• If equipment requiring AC power is mounted to this unit,
haveacertiedelectricianinspecttheinstallation.
• Failure to install this unit according to these instructions
will void all ICW warranties. If installed incorrectly, ICW
is not liable for any damage or injury caused by the unit.
The Elite arm contains high pressure gas
springs. The following cautions MUST be
observed to avoid serious injury.
DANGER!
RELEASE ARM RESISTANCE
Extend the Elite straight out as shown
before releasing the arm’s resistance.
Be sure all equipment is mounted on
the arm before adjusting.
Completely release the
resistance of the arm section
closest to the monitor. Use
the T-handle provided.
DO NOT USE
POWER TOOLS TO ADJUST
END COVERS:
Remove the end
covers by unscrewing
the two 3/4” long
10-24atheadscrews
using a Phillips head
screwdriver.
CENTER COVER:
Remove the center
cover by unscrewing
the four 3/4” long
10-24atheadscrews
using a Phillips head
screwdriver.
TOP COVERS:
Remove the long
arm covers by
unscrewing the
two 1/4” long 6-32
atheadscrews
in the center of
the cover using
a Phillips head
screwdriver.
TORQUE 120 INCH POUNDS. DO NOT LOOSEN.
REMOVE ARM COVERS
REPLACE BOLT & BEARING ASSEMBLIES
Fold arm. Remove
existing bolt and bearing
assemblies beneath the
Elite foot. Replace with
new hardware provided.
40mm ID
bearing
assembly
3/8 bolt
assembly
with 3/8 ID
bearing
REMOVE MONITOR
Unplug and remove the
monitor by unscrewing
the adjustment knob.Save
all hardware. Remove
keyboard or secure it to
keyboard tray.
If you have any questions, please call our
customer service representatives. They will be
able to answer your installation questions.
Toll free 1-800-558-4435

ELITE 5220 BEARING REPLACEMENT - 05/02/16 pjm
ELITE 5220 REAR BEARING REPLACEMENT
Page 2 of 2
REATTACH ARM COVERS
TOP COVERS:
Reattach the long arm covers by replacing the two
1/4”long6-32atheadscrewsinthecenterofthe
cover using a Phillips head screwdriver.
CENTER COVER:
Reattach the center cover by replacing the four 3/4”
long10-24atheadscrewsusingaPhillipshead
screwdriver.
END COVERS:
Reattach the end covers by replacing the two 3/4”
long10-24atheadscrewsusingaPhillipshead
screwdriver.
ADJUST ARM RESISTANCE
Extend the Elite straight out as
shown before increasing the
arm’s resistance. Be sure all
equipment is mounted on the
arm before adjusting.
DO NOT USE
POWER TOOLS TO ADJUST
Replacing the rear bearing assemblies on the Elite 5220 may require two people.
END COVERS:
Remove the end
covers by unscrewing
the two 3/4” long
10-24atheadscrews
using a Phillips head
screwdriver.
CENTER COVER:
Remove the center
cover by unscrewing
the four 3/4” long
10-24atheadscrews
using a Phillips head
screwdriver.
TOP COVERS:
Remove the long
arm covers by
unscrewing the
two 1/4” long 6-32
atheadscrews
in the center of
the cover using
a Phillips head
screwdriver.
TORQUE 120 INCH POUNDS. DO NOT LOOSEN.
REMOVE ARM COVERS
ATTACH MONITOR
Attach the monitor by
screwing the knob through
the rail into the VESA.
REPLACE BOLT & BEARING ASSEMBLIES
Fold arm. Remove
existing bolt and bearing
assemblies beneath the
wall ear. Replace with
new hardware provided.
This process may be easier if one person holds and
lifts the arm up while a second person installs the
replacement bolt and bearing assemblies.
3” Needle
bearing
If you have any questions, please call our
customer service representatives. They will be
able to answer your installation questions.
Toll free 1-800-558-4435