IDW G-Series User manual

G-Series Cooler
Instruction Manual
GCG-10
UPRIGHT COOLER
Manual is for the following models:
GCG-10-N33EB
G-10-N33EB

1
GCG-10
Instruction Manual
Manual is for the following models:
GCG-10-N33EB
G-10-N33EB

Innovative DisplayWorks
GCG-10
FOR YOUR FUTURE REFERENCE
• This easy-to-use manual will guide you in getting the best use of your cooler.
• Remember to record the model number and the serial number. This information can be found on the
inside of your cooler.
• Keep your receipt with this manual for future warranty service.
Model #:
Serial #:
Date of Purchase:
2
TABLE OF CONTENTS
Safety Precautions ..............................................................3
Parts & Identication ..........................................................4
Features..............................................................................5
Flammable R290 Warnings .................................................5
Instructions.........................................................................5
Ambient Environment..........................................................5
Preparation Before Operation..............................................6
Removal of Light Canopy & Instruction ................................7
Lamp Decoration, Illumination & Switches...........................8
Startup, Operation & Temperature Adjustment.....................9
Lit Door ‘Logo’ Switch..........................................................9
Repair & Maintenance for Refrigeration Drawer...................9
Condenser Maintenance ....................................................10
Maintenance.....................................................................10
Cleaning Shutdown Questions & Answers...........................10
Troubleshooting ................................................................ 11
After-Sales Service............................................................. 11
Specications.................................................................... 12
Circuit Diagrams ............................................................... 12

Instruction Manual
3
Innovative DisplayWorks
offi ce 909.447.8254 • fax [phone] • toll free 877.307.2665 • www.idw.global
PARTS & IDENTIFICATION
Last Revised: August 19, 2015 6:28 PM
GCG-10
1. Cabinet
2. Upper Hinge
3. Bushings
4. Rubber Hinge Cover
5. Wire Sleeve
6. Top Hinge Cover
7. Evaporator Bracket
8. Evaporator
9. Fan Baffl e
10. Evaporator Fan
11. Evaporator Fan Motor Bracket
12. Thermostat Bolt
13. Thermostat
14. Thermostat Label
15. Evaporator Fan Shroud
16. Door Upper Trim
17. Door Gasket
18. Glass Door
19. LED Light
20. Inner Light Wires
21. Door Side Light Wires
22. Door Bottom Trim
23. Door Stop
24. Bottom Hinge Washer
25. Key
26. Lock
27. Glass Door Light Covers (GCG
models only)
28. Front Grill Clip
29. Front Grill
30. Transformer (1A)
31. Transformer (600mA)
32. Transformer for Evaporator Fan
33. Transformer Box
34. Leveling Legs (4)
35. Castor Installation Base
36. Transformer Box
37 Wire Tray Bracket
38. Bottom Hinge
39. Shelf Strip
40. Wire Protector Cover
41. Thermostat Connecting Wire
42. Transformer Connecting Wire
43. Fan Connecting Wire
44. Wire Clips
45. Shelf Clips
46. Drain Funnel Support
47. Flat Shelf
48. Inside Light Cover
49. Light Cover Bracket
50. Inner Drain Pan
51. Drain Pipe
52. Interior Rear Holder
53. Lock Holder
54. Overload Breaker
55. Starter Relay
56. Glass Door Support
57. Condenser Fan
58. Condenser Fan Motor Bracket
59. Condenser Fan Blade
60. Junction Box
61. Defrost Timer
62. Electrical Board
63. Condenser
64. Drip Pan
65. Connecting Pipe
66. Compressor Base
67. Filter Drier Bracket
68. Filter Drier Clip
69. Filter Drier
70. Drain Connected Pipe
71. Hoop
72. Compressor
73. Plastic Clip
74. Rear Compartment Grill
75. Power Cord Holder
76. Power Cord
77. Light Switch
78. Switch Box
79. Switch Box Cover
80. Suction Tube
81. Left Glass Door Light Cover
82. Right Glass Door Light Cover

Innovative DisplayWorks
GCG-10
4
SAFETY PRECAUTIONS
When using this appliance, always follow the basic safety precautions:
1. Read the entire User’s Manual before operating this appliance.
2. Use this appliance only for its intended purpose as described in this User’s Manual.
3. This cooler must be properly installed in accordance with the installation instructions before being used. See grounding
instructions on page 6.
4. Never unplug your cooler by pulling on the power cord. Always grasp the plug  rmly and pull it straight out from the
outlet.
5. Unplug your cooler before cleaning or making any repairs. (Note: If for any reason this product requires service, we
strongly recommend that a certi ed technician perform the service.)
6. Immediately repair or replace all electrical cords that have become frayed or otherwise damaged. Do not use a cord that
shows cracks or abrasion damage along its length, the plug or the connector end.
7. This cooler should not be recessed or built into an enclosed cabinet. It is designed for freestanding installation only.
8. Do not operate or store your cooler near or around explosive fumes, gasoline or other fl ammable vapors and liquids.
9. Setting the temperature control to the 0 position does not remove power to the light circuit, perimeter heaters, or
evaporator fans.
Please save these instructions!
DANGER!
Proper Disposal of the Refrigerator
To prevent any risk of child entrapment when discarding your cooler remove the doors and leave the shelves in place so that
children cannot easily climb inside.
PRE-CAUTION, NON-OPERATING COOLERS SHOULD HAVE:
1. Glass door removed.
2. Shelves kept in place in order to prevent any small child from climbing inside cooler.
FOR PROPER DISPOSAL OF COOLER: Distributors / retailers need to contact a quali ed service technician:
1. To recover all Freon/refrigerant from the cooler
2. To remove the compressor or remove the oil from the compressor
Then the distributor/ retailer can contact their local metal recycling center to pick up the remaining cabinet, shelves, etc. By law,
disposal of hazardous wastes may be subject to  nes and imprisonment under the provisions of the environmental regulations.
For more information please visit: http://www.epa.gov/osw/hazard/index.htm

Instruction Manual
5
FEATURES
•Designed with an elegant shape and quick refrigeration speed, this commercial-grade product is an ideal choice for
shopping malls, supermarkets, hotels, etc.
•Transparent glass doors are built with hollow, toughened glass that provides a high level of heat insulation. Clear
doors allow for high product visibility.
•The forced air system allows for fast cooling speeds, which helps maintain a consistent temperature.
•Adjustable shelves allow for a wide variety of products to be stocked.
•A built-in lock offers the ability to secure products.
•The refrigeration unit is designed for easy access, allowing for fast and simple repairs.
•This equipment is intended for storage and display of non-hazardous packaged product.
CAUTION FLAMMABLE REFRIGERANT
• DANGER – Risk Of Fire Or Explosion. Flammable Refrigerant Used. To Be Repaired Only By Trained Service
Personnel. Do Not Puncture Refrigerant Tubing.
• CAUTION – Risk Of Fire Or Explosion. Flammable Refrigerant Used. Consult Repair Manual/Owner’s Guide
Before Attempting To Install or Service This Product. All Safety Precautions Must be Followed.
• CAUTION – Risk Of Fire Or Explosion. Dispose Of Properly In Accordance With Federal Or Local Regulations.
Flammable Refrigerant Used.
• CAUTION – Risk Of Fire Or Explosion Due To Puncture Of Refrigerant Tubing; Follow Handling Instructions
Carefully. Flammable Refrigerant Used.
INSTRUCTIONS
Ambient Environment
•Place cooler on an even surface to reduce vibration and noise.
•To transport, do not tilt the cooler beyond a 45 degree angle.
•Do not place cooler in direct sunlight or near any heat sources.
•Do not place cooler in environment temperatures that exceed 109°F.
•Do not place cooler in below normal temperatures.
•Do not place cooler in extreme humid environments, this may cause components to rust.
•Do not place cooler near constant running or splattering water, this may cause immediate damage to refrigeration
system.
•Must allow at least 2” between rear of cooler and wall for proper ventilation and heat dissipation of cooler.
•Do not place furniture or other articles with sharp edges near the cooler in order to prevent damage to the glass door.
DANGER – Risk Of Fire Or Explosion. Flammable Refrigerant Used. To Be
Repaired By Trained Service Personnel Only. Do Not Puncture Refrigerant Tubing.
CAUTION – Risk Of Fire Or Explosion. Flammable Refrigerant Used. Consult
Repair Manual/Owner’s Guide Before Attempting To Service This Product. All
Safety Precautions Must be Followed.
CAUTION – Risk Of Fire Or Explosion. Dispose Of Property In Accordance With
Federal Or Local Regulations. Flammable Refrigerant Used.
CAUTION – Risk Of Fire Or Explosion Due To Puncture Of Refrigerant Tubing;
Follow Handling Instructions Carefully. Flammable Refrigerant Used.
CAUTION FLAMMABLE - R600a Refrigerant
DANGER - Risque d'incendie ou d'explosion. Réfrigérant inflammable utilisé.
Pour être réparé que par un personnel de maintenance qualifié. Ne pas percer
réfrigérant Tubing.
ATTENTION - Risque d'incendie ou d'explosion. Réfrigérant inflammable utilisé.
Consultez manuel / guide de l 'utilisateur de réparation avant de tenter de
réparer ce produit. Toutes les précautions de sécurité doivent être respectées.
ATTENTION - Risque d'incendie ou d'explosion. Aliéner des biens conformé-
ment à la réglementation fédérales ou locales. Réfrigérant inflammable utilisé.
ATTENTION - Risque d'incendie ou une explosion due à la perforation de
tuyaux de réfrigérant; suivre les instructions de manipulation avec précaution.
Réfrigérant inflammable utilisé.
PRUDENCE INFLAMMABLE - R600a Réfrigérant

Innovative DisplayWorks
GCG-10
6
PREPARATION PRIOR TO OPERATION
•Remove all packaging materials before using cooler.
This includes: foam pedestal, adhesive tape (used to x accessories) and protective gaskets.
• Inspect cooler for concealed damage. Immediately le a claim with the freight carrier if there is damage. IDW is not
responsible for damage incurred during shipping.
•For proper operation, place the cooler on a dry, level surface.
•Clean the interior surface with a soft cloth and lukewarm water before operation.
•Keep cooler in an upright position for 30 minutes prior to use.
•IDW requires that a sole use circuit be dedicated for the unit. Failure to do so voids warranty.
WARNING: Do not use extension cords.
WARNING: Compressor warranties are void if compressor burns out due to low voltage.
WARNING: Power supply cord should not be removed or altered in any way.
Leveling
• Set unit in its nal location, making certain there is adequate ventilation in the room.
WARNING: Warranty is void if ventilation is insufcient.
•Proper leveling of the GCG-10 cooler is critical to it operating correctly. Condensation removal and door operation will
be affected by leveling.
<The cooler should be leveled front to back and side to side with a level.
•Ensure that drain hose or hoses are positioned in the pan.
•Remove plug and cord from inside the lower rear of the cooler.
•The unit should be placed close enough to the electrical supply so that extension cords are
never used.
Shelving Installation
• Securely insert shelf clips into pilasters
• Shelf clips should be level so shelf lays fl at
• Place shelf on shelf clips

Instruction Manual
Replacing the Canopy Light
• Updating the removal of the light canopy
1 Unplug the cooler, then unscrew (2) screws using a Phillip’s screwdriver.
5Remove LED light strand.
6To install LED lights follow the above directions in reverse order.
2Remove plastic cover.
4 Unscrew (2) screws using a Phillip’s screwdriver.
3Disconnect lights.
7

Innovative DisplayWorks
GCG-10
REPLACING THE DOOR LIGHTS
There are LED lights inside the top of the cabinets and in the door. GCG-10 has Interior top canopy lights and inner side door
lights. Replacement of LED lights in the door:
1Unplug the cooler.
2Remove plastic cover.
3Disconnect top light
strand.
4Disconnect middle light strand.
5Unscrew light strand.
8
6Remove entire light strand.
7To install LED lights follow the above instructions in reverse order.
Notes: If there are any malfunctions with the main control panel of LED lights, please contact a
professional for replacement.

Instruction Manual
STARTUP, OPERATION AND TEMPERATURE ADJUSTMENT
Operation
• Prior to stocking cooler with product, it should be operated empty for half an hour.
Temperature Adjustment
Lit Door “Logo” Switch
Operation
• The light switch located at the rear of the cabinet on the right-hand side
is the ON/OFF switch for the Lit logo located on the door of the cooler.
REPAIR AND MAINTENANCE FOR REFRIGERATION DRAWER
* A CERTIFIED TECHNICIAN IS REQUIRED TO REPAIR ALL REFRIGERATION COMPONENTS FOR WARRANTY
PURPOSES.
For convenient repair, the refrigeration components (compressor, evaporator, condenser, evaporation
fan, condensation fan and lter) are designed using a split system; any component can be easily
replaced. Replacement procedure is as follows:
1Unplug the unit.
2Remove the screws from the front grill, and then remove the grill.
3Unplug all connections and terminals that are in need of repair.
6After repair, re-install all parts using the reverse procedure.
9
•GCG-10 performance testing position of the thermostat is around 3.5-5.
4Using a screwdriver, remove screws from component.
5Slide the Refrigeration Drawer out to easily access
refrigeration components. Remove the component to
replace or repair.
MAINTENANCE
Cleaning
• Unplug the cooler before cleaning.
• Use a soft cloth or sponge with water or soap (non-corrosive mild detergent). After cleaning, wipe the cooler using a
dry cloth to prevent the cooler from rusting.
• Do not spray water on the cooler, and do not use hard or steel brushes to clean the cooler.
• Do not use organic solvents, boiling water, washing powders or acids while cleaning.
If the cooler will be in a non-operational state for a long period of time, clean as
instructed above, and keep the door open until interior is dry.

Innovative DisplayWorks
GCG-10
CONDENSER MAINTENANCE
It is essential to keep the condenser coils clean and free of dust and debris at all times. It is required to periodically clean
the condenser coils with a soft bristle brush or vacuum-cleaner to properly maintain the refrigeration system. Failure to
clean the condenser at regular intervals may cause failure of the refrigeration system and could void the warranty.
1 Remove the rubber cap from the front Grill.
2Using a small Phillips head screwdriver, remove the two screws as shown above.
3The front plastic grill can now be removed by pulling it up.
4Using plastic bristle brush, carefully clean the coil being aware that coils
can bend or be damaged if too much force is used - shown below.
5Replace grill and utilize the Phillips screwdriver to tighten the screws into
place, replace the rubber caps.
10
MAINTENANCE
Cleaning
• Unplug the cooler before cleaning.
• Use a soft cloth or sponge with water or soap (non-corrosive mild detergent). After cleaning, wipe the cooler using a
dry cloth to prevent the cooler from rusting.
• Do not spray water on the cooler, and do not use hard or steel brushes to clean the cooler.
• Do not use organic solvents, boiling water, washing powders or acids while cleaning.
If the cooler will be in a non-operational state for a long period of time, clean as
instructed above, and keep the door open until interior is dry.

Instruction Manual
11
TROUBLESHOOTING
The following are not Malfunctions:
Issues Solutions
Liquid fl owing noise within cooler This liquid is the sound of the cooling agent fl owing through the pipes.
Refrigeration system is shutdown for
longer periods of time while temperature
inside is still very low.
This refrigerator has a strong level of heat preservation and can main-
tain a relatively ambient temperature.
Condensation on glass door This may be due to a high indoor humidity or a low inside temperature
value may be set. Wipe the door dry with a towel.
1This refrigerator has been designed and manufactured according to National standards. If there are any questions
during use, refer to this operation manual to help troubleshoot problems.
2When disposing of the cooler, please remove the door and lock assembly to avoid children accidentally becoming
trapped inside the cooler.
AFTER SALES SERVICE
Any product has the possibility of malfunction. Please observe the cooler’s operation and any changes to product being
stored. If there are any abnormal cases, refer to the table below. If there is still no change after following the below
instructions, please inform our service center in a timely manner to avoid a further loss of the unit.
Issues Solutions
Cooler is not functioning. Please check power supply:
• Fuse damage
• The plug is not securely inserted into the wall socket
• Check for low voltage
Cooler is not keeping product cool. • Provide ample space between all products to ensure proper
circulation of air.
• Keep unit away from direct sunlight or other heating source.
• Keep door closed as often as possible.
• Be certain cooler is not touching external objects or walls.
Excessive noise • Be certain the cooler is placed on a level surface.
• Be certain cooler is not touching external objects or walls.

Innovative DisplayWorks
GCG-10
12
TROUBLESHOOTING
If your cooler is not working properly:
• Check the electrical outlet for power, and that the plug is properly inserted.
• Check to see if the circuit breaker is tripped or the fuse is blown.
• Check the condenser for proper cleaning.
If your cooler is making noise:
• Check that the cooler is level and on a fl at surface.
If the compressor turns on and off frequently:
• The room temperature is higher than normal.
• The door is not closed completely.
• The door gasket is not sealed well.
• There is insuf cient clearance around the cooler.
• The temperature is not set properly.
• The cycling frequency will reduce when all of the cans reach the set temperature.
The following is not a malfunction:
• It is normal to hear gurgling sounds caused by the fl ow of refrigerant when each cooling cycle ends.
REFRIGERANT
• The cooler utilizes R134a refrigerant.
SPECIFICATIONS
Model:
Power Supply (V/Hz):
Dimension (W x D x H):
Box Dimension (W x D x H):
Maximum Load Per Shelf:
NSF-7 Standard: This equipment is intended for the storage and display of non-potentially
hazardous bottled or canned products only.
GCG-10 Upright Cooler
110V/60Hz
25.25” x 26” x 54”
28” x 27.5” x 58.25”
CIRCUIT DIAGRAM
Model GCG-10-N33EB
CIRCUIT DIAGRAM
Model G-10-N33EB

Innovative DisplayWorks, Inc.
To locate the distributor in your area go to: http://www.idw.global/contact/#distributors