IDW GS-2.5-N23EB User manual

G-Series Cooler
Instruction Manual
Manual is for the following model:
GS-2.5-023EB
GS-2.5-N23EB
GS-2.5-223EB
GS-2.5-A23EB
GS-2.5
COUNTERTOP COOLER

Innovative DisplayWorks
GS-2.5
Instruction Manual
Manual is for the following model:
GS-2.5-023EB
GS-2.5-N23EB
GS-2.5-223EB
GS-2.5-A23EB

GS-2.5
Innovative DisplayWorks
FOR YOUR FUTURE REFERENCE
• This easy-to-use manual will guide you in getting the best use of your cooler.
• Remember to record the model number and the serial number. This information can be found on the
inside of your cooler.
• Keep your receipt with this manual for future warranty service.
Model #:
Serial #:
Date of Purchase: TABLE OF CONTENTS
Parts and Identication ......................................... 2
Safety Instructions................................................. 3
Installation ........................................................... 3
Electric Connection ................................................ 3
Start ..................................................................... 3
Maintenance......................................................... 4
Cleaning ............................................................... 4
Condenser Maintenance ........................................ 4
Light Replacement................................................. 4
Power Failure........................................................ 4
Moving the cooler.................................................. 4
Drip Pan ............................................................... 4
Troubleshooting .................................................... 5
Refrigerant ........................................................... 5
Specications........................................................ 5
Switch Function..................................................... 6
Flammable R600a Warnings ................................. 6
Circuit Diagram..................................................... 7
1

Instruction Manual
Innovative DisplayWorks
2
SAFETY INSTRUCTIONS
To reduce the risk of  re, electric shocks, or injury when using your cooler, please note the following basic precautions:
• Never clean appliance parts with fl ammable fl uids.
• Do not store or use gasoline or any other fl ammable vapors and liquids in the vicinity of this or any other appliance.
The fumes can cause a  re or explosion.
• As with all electrical appliances, please consult a licensed repair technician for any repairs.
• Do not block the ventilation holes located on the top of the cabinet.
INSTALLATION
• Keep cooler in an upright position for 1-hour prior to use. This is essential for proper operation. If the cooler is
transported in the horizontal position, the cooler must be returned to the upright position and not plugged in for 1
hour.
• Remove all the packing material before using your cooler.
• Clean the interior surface with a soft cloth and lukewarm water.
• If the cooler is transported in the horizontal position, check the drain pan and ensure that it is properly positioned
above the compressor.
• For proper operation, place the cooler on a dry, level surface.
• Place the cooler at least 4” away from any walls. Otherwise, this could cause damage to the electrical cord and block
the air circulation to the appliance.
• Do not block the air intake that ventilates the condenser unit.
ELECTRIC CONNECTION
• This model operates with an 115V/60Hz power supply. Check the electrical outlet for proper voltage.
• Warning: Plug unit directly into wall outlet. Do not use an extension cord or any other multiple connectors.
• For your safety, plug the unit into a grounded wall outlet.
START
• Plug the cooler into the electrical outlet. For optimum performance, run cooler for 3 hours prior to use.
• Temperature Control: Do not adjust the temperature control. The temperature control is factory set to provide
maximum performance. If really necessary, you can turn the thermostat by screw driver clockwise to have lower
temperature inside the cooler
LIGHT CONTROL
• The inside light is controlled by the magnetic switch.
BEFORE USING, PLEASE READ ALL INSTRUCTIONS
Innovative DisplayWorks
offi ce 909.447.8254 • fax [phone] • toll free 877.307.2665 • www.idw.global
PARTS & IDENTIFICATION
Last Revised: April 12, 2017 10:39 AM
GS-2.5
1. Cooler Cabinet
2. Interior Light Bracket
3. Interior LED
4. Interior Lampshade
5. Interior Lampshade Board (2)
6. Evaporator
7. Circle Pipe
8. Evaporator Fan
9. Evaporator Safeguard
10. Evaporator Fan Cover
11. Rear Grill
12. Door Gasket
13. Glass Door
14. Top Hinge
15. Hinge Cover
16. Bottom Hinge
17. Bottom Hinge Washer
18. Door Lock
19. Key (2)
20. Large Shelf (2)
21. Pilasters (4)
22. Shelf Clip (8)
23. Lockpin
24. Magnetic Switch
25. Condenser Support (4)
26. Thermostat
27. Transformer 1A
28. Condenser Fan Transformer
29. Junction Box
30. Transformer Box
31. Transformer Box
32. Foot (4)
33. Compressor Panel
34. Compressor
35. Drip Pan
36. Thermostat Box
37. Thermostat Box Cover
38. Thermostat Label
39. Door Light Switch (2)
40. Filter Drier
41. Condenser Fan
42. Condenser Fan Cover
43. Fan Cover
44. Power Cord
45. Condenser
46. LED Lights (2)

GS-2.5
Innovative DisplayWorks
3
SAFETY INSTRUCTIONS
To reduce the risk of  re, electric shocks, or injury when using your cooler, please note the following basic precautions:
• Never clean appliance parts with fl ammable fl uids.
• Do not store or use gasoline or any other fl ammable vapors and liquids in the vicinity of this or any other appliance.
The fumes can cause a  re or explosion.
• As with all electrical appliances, please consult a licensed repair technician for any repairs.
• Do not block the ventilation holes located on the top of the cabinet.
INSTALLATION
• Keep cooler in an upright position for 1-hour prior to use. This is essential for proper operation. If the cooler is
transported in the horizontal position, the cooler must be returned to the upright position and not plugged in for 1
hour.
• Remove all the packing material before using your cooler.
• Clean the interior surface with a soft cloth and lukewarm water.
• If the cooler is transported in the horizontal position, check the drain pan and ensure that it is properly positioned
above the compressor.
• For proper operation, place the cooler on a dry, level surface.
• Place the cooler at least 4” away from any walls. Otherwise, this could cause damage to the electrical cord and block
the air circulation to the appliance.
• Do not block the air intake that ventilates the condenser unit.
ELECTRIC CONNECTION
• This model operates with an 115V/60Hz power supply. Check the electrical outlet for proper voltage.
• Warning: Plug unit directly into wall outlet. Do not use an extension cord or any other multiple connectors.
• For your safety, plug the unit into a grounded wall outlet.
START
• Plug the cooler into the electrical outlet. For optimum performance, run cooler for 3 hours prior to use.
• Temperature Control: Do not adjust the temperature control. The temperature control is factory set to provide
maximum performance. If really necessary, you can turn the thermostat by screw driver clockwise to have lower
temperature inside the cooler
LIGHT CONTROL
• The inside light is controlled by the magnetic switch.
BEFORE USING, PLEASE READ ALL INSTRUCTIONS

Instruction Manual
Innovative DisplayWorks
4
MAINTENANCE
Cleaning
• Before cleaning the appliance, always remember to unplug it.
• Unplug the cooler at the electrical outlet; never pull the service cord.
• Do not use sharp or pointed objects for cleaning.
• Clean the inside cabinet of the cooler with a clean damp cloth. Avoid damage by using non-abrasive and non-
fl ammable cleaning products.
• Clean the condenser at least once a month with a vacuum cleaner or a brush to
eliminate the dust accumulation.
Light Replacement
• Unplug the cooler before removing the LED light strip.
• Remove the screws.
• Remove the light cover gently.
• Take out the LED light strip.
• Replace the used strip with new equivalent light strip.
• Install the light cover and tighten the screws.
• Plug in the cooler.
Power Failure
• Please minimize the frequency of opening the door during a power failure.
• If your cooler is unused for an extended period of time, unplug, empty, and clean your cooler and keep the door open
to avoid condensation, formation of mold, or odors.
Moving The Cooler
• Empty the unit.
• Secure all loose parts inside the cooler.
• Tape the door shut.
• During transportation, make sure that the cooler is in an upright position.
Drip pan
• During normal compressor cycle, water will drain into the drain pan and evaporate.
• To clean, gently pull the drain pan towards you and remove. Slowly reinstall it after cleaning.

GS-2.5
Innovative DisplayWorks
5
TROUBLESHOOTING
If your cooler is not working properly:
• Check the electrical outlet for power, and that the plug is properly inserted.
• Check to see if the circuit breaker is tripped or the fuse is blown.
• Check the condenser for proper cleaning.
If your cooler is making noise:
• Check that the cooler is level and on a fl at surface.
If the compressor turns on and off frequently:
• The room temperature is higher than normal.
• The door is not closed completely.
• The door gasket is not sealed well.
• There is insuf cient clearance around the cooler.
• The temperature is not set properly.
• The cycling frequency will reduce when all of the cans reach the set temperature.
The following is not a malfunction:
• It is normal to hear gurgling sounds caused by the fl ow of refrigerant during each cooling cycle.
REFRIGERANT
• The cooler utilizes R600a refrigerant.
SPECIFICATIONS
Model:
Power Supply (V/Hz):
Dimension (W x D x H):
Box Dimension (W x D x H):
Maximum Load Per Shelf:
NSF-7 Standard: This equipment is intended for the storage and display of non-potentially
hazardous bottled or canned products only.
GS-2.5
GS-2.5 Countertop Cooler
110V/60Hz
18.5” x 21” x 27.5”
20.25” x 22.25” x 29”

Instruction Manual
Innovative DisplayWorks
6
SWITCH FUNCTION
Switch Status Interior LED Switch Door LED
Switch Remark
I / I ON ON Interior ON and Door logo ON
I / O ON OFF Interior ON and Door logo OFF
O / I OFF ON Interior OFF and Door logo ON, interior LED turns
ON when door opens
O / O OFF OFF Interior OFF and Door logo OFF, interior LED turns
ON when door opens
• CAREFUL - Handling, moving and oporating of the refrigerator or freezer to avoid either damaging the
refrigerant tubing, or increasing the risk of a leak.
• CAUTION - Component parts shall be replaced with like components and that servicing shall be done by
factory authorized service personnel, so as to minimize the risk of possible ignition due to incorrect parts or
improper service.

GS-2.5
Innovative DisplayWorks
CIRCUIT DIAGRAM
GS-2.5-023EB
CIRCUIT DIAGRAM
GS-2.5-N23EB
7

Instruction Manual
Innovative DisplayWorks
CIRCUIT DIAGRAM
GS-2.5-223EB
CIRCUIT DIAGRAM
GS-2.5-A23EB
8

GS-2.5
Innovative DisplayWorks

Innovative DisplayWorks, Inc.
To locate the distributor in your area go to: http://www.idw.global/contact/#distributors
G-Series Cooler
Instruction Manual