IEI Technology PulM Series User manual

www.ieiworld.com
PulM Series
PulM-1G4T-I211-BP
Networking Module Quick Installation Guide
Torx Screws x 2 Torx Wrench x 1
PulM-1G4T-I211-BP
Package Contents
LAN Port
Link
LED
Speed
LED
Ethernet 1G
Ethernet 1G
Ethernet 1G
Ethernet 1G
Intel®
I211
Intel®
I211
Intel®
I211
PCIe 2.0
A19
A32
4 PCIe 2.0 x2
Bypass
A19
0
A32
PCIe CONF. MODE
0Four x2 Intel®
I211 RJ-45
RJ-45
RJ-45
RJ-45
PulM-1G4T-I211-BP Block Diagram
LAN LED Status
LED State Description
Link (Left) Yellow Active
Speed (Right) Orange 1 Gbps date rate
Green 100 Mbps data rate
O (Left/Right) O Bypass function
A32 A19
B
A32 A19
A
Slot A
PCIe Conguration
x4
x8
x4
Slot B
PCIe Conguration
x4
x2 x2 x2 x2
x4
A19 A32 PCIe Cong. Slot
00 4x2 B
0 1 2x4 A & B
10 1x8 A
PCHCPU
Hardware Installation
Slot A Slot B
Install the PulM-1G4T-I211-BP networking module into the slot of the
PUZZLE series. The Slot A supports 8 lanes from CPU (1 PCIe x8 or 2
PCIe x4); the Slot B supports 8 lanes from PCH (2 PCIe x4 or 4 PCIe x2).
When the PulM-1G4T-I211-BP is installed in the Slot A, only two LAN
ports (port 1 & port 3) are active; however, the 2-pair bypass is still
available.
Four PCIe x2 or
Two PCIe x4
One PCIe x8 or
Two PCIe x4
DMI GEN3 x4

Networking Module Installation
Use the Torx wrench to remove the two Torx
screws. Remove the slot cover. Save the slot
cover screws.
Slide an IEI networking module into the slot
until the module is seated in the slot correctly
and securely.
Install the previously-removed Torx screws to
secure the module to the chassis.
1
Step 2 Step 3 Step
Bypass Conguration in BIOS
Congure the Power_ON ByPass Mode and the Power_OFF ByPass
Mode BIOS options to enable/disable bypass function of the installed
PulM modules.
3
Step
Press F4 to save and exit the BIOS menu. The PUZZLE series will reboot
with the new settings.
4
Step
Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc.
Chipset
Network ByPass setting
Slot_A Model Name PulM-10G4SF-XL710
Power_ON ByPass Mode [Disabled]
Power_OFF ByPass Mode [Enabled]
Slot_B Model Name PulM-1G4T-I211-BP
Power_ON ByPass Mode [Disabled]
Power_OFF ByPass Mode [Enabled]
Switch all ByPass Mode
to Enable/Disable
after power on.
---------------------
 : Select Screen
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized
Defaults
F4: Save & Exit
ESC: Exit
Version 2.20.1271. Copyright (C) 2018 American Megatrends, Inc.
Power_ON ByPass
Disabled
Enabled
Some PulM modules support bypass. To enable/disable bypass function, congure the BIOS menu of the PUZZLE series as described below.
Go to Chipset PCH - IO Conguration NETWORK Conguration
(Bypass Setting)
The Network ByPass Setting menu appears. The model names of the
PulM module installed in the PUZZLE series are shown.
1
Step 2 Step
Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc.
Chipset
Network ByPass setting
Slot_A Model Name Not Installed
Power_ON ByPass Mode [Disabled]
Power_OFF ByPass Mode [Enabled]
Slot_B Model Name PulM-1G4T-I211-BP
Power_ON ByPass Mode [Disabled]
Power_OFF ByPass Mode [Enabled]
Switch all ByPass Mode
to Enable/Disable
after power on.
---------------------
 : Select Screen
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized
Defaults
F4: Save & Exit
ESC: Exit
Version 2.20.1271. Copyright (C) 2018 American Megatrends, Inc.
Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc.
Chipset
PCH-IO Configuration
Auto Power Button Status [Disable (ATX)]
Status
Restore AC Power Loss [Last State]
> PCI Express Configuration
> SATA And RST Configuration
> NETWORK Configuration (ByPass Setting)
M.2 B Key (M2_1) [SATA]
Device selection
Module B Configuration [PCIEx4 x 2]
Select AC power state
when power is re-
applied after a power
failure.
---------------------
 : Select Screen
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized
Defaults
F4: Save & Exit
ESC: Exit
Version 2.20.1271. Copyright (C) 2018 American Megatrends, Inc.
PUZZLE BIOS
Setting
Power_ON ByPass Mode Power_OFF ByPass Mode
Disabled Enabled Disabled Enabled
PulM Bypass
Function
Disable bypass
when system on
Enable bypass
when system on
Disable bypass
when system o
Enable bypass
when system o