IEI Technology ACT-412A-N270 User manual

ACT-412A-N270 User Manual
Page i
IEI Technology Corp.
User Manual
MODEL:
ACT-412A-N270
Panel PC with Touch Screen and 1.6 GHz Intel® Atom™ CPU
Gigabit Ethernet, 3 USB, Audio, RS-232/422/485, eSATA, SATA
RoHS Compliant, IP 64 Protection
Rev. 1.20 – 3 September, 2010

ACT-412A-N270 User Manual
Page ii
Revision
Date Version Changes
3 September, 2010 1.20 LCD panel update
30 September, 2009 1.00 Initial release

ACT-412A-N270 User Manual
Page iii
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

ACT-412A-N270 User Manual
Page iv
Table of Contents
1 INTRODUCTION........................................................................................................ 12
1.1ACT-412A-N270ALL-IN-ONE ACCESS CONTROL TERMINAL ................................. 13
1.1.1 Features ........................................................................................................... 13
1.1.2 Applications ..................................................................................................... 14
1.2 EXTERNAL OVERVIEW.............................................................................................. 14
1.2.1 Front Panel...................................................................................................... 14
1.2.2 RFID Reader.................................................................................................... 16
1.2.3 Rear Panel ....................................................................................................... 16
1.2.4 Bottom Panel.................................................................................................... 16
1.2.5 CompactFlash® Slot........................................................................................ 17
1.3 INTERNAL OVERVIEW............................................................................................... 18
1.4 SPECIFICATIONS ....................................................................................................... 18
1.4.1 System Specifications....................................................................................... 18
1.5 DIMENSIONS............................................................................................................. 20
2 INSTALLATION ......................................................................................................... 22
2.1 UNPACKING.............................................................................................................. 23
2.1.1 Packing List ..................................................................................................... 23
2.2ANTI-STATIC PRECAUTIONS ..................................................................................... 25
2.3 INSTALLATION PRECAUTIONS................................................................................... 25
2.4 PREINSTALLED COMPONENTS................................................................................... 26
2.5 INSTALLATION AND CONFIGURATION STEPS ............................................................. 26
2.6 REAR PANEL REMOVAL ............................................................................................ 26
2.7 HARD DRIVE INSTALLATION..................................................................................... 27
2.8 CF CARD INSTALLATION .......................................................................................... 28
2.9 SYSTEM POWER ....................................................................................................... 29
2.9.1.1 ATX Power Mode (Default)...................................................................... 30
2.9.1.2 AT Power Mode ........................................................................................ 30
2.9.2 Power Adapter................................................................................................. 30
2.10 JUMPER SETTINGS.................................................................................................. 31
2.10.1 Access the Jumpers........................................................................................ 31

ACT-412A-N270 User Manual
Page v
2.10.2 Preconfigured Jumpers.................................................................................. 32
2.10.3 Clear CMOS Jumper...................................................................................... 33
2.10.4 COM Port Pin 9 Select .................................................................................. 34
2.10.4.1 COM3 RS-422 and RS-485 Pinouts....................................................... 35
2.10.5 COM3 RX Function Select Jumper................................................................ 36
2.10.6 COM3 TX Function Select Jumper................................................................ 37
2.10.7 COM3 RS-232/422/485 Serial Port Select Jumper ....................................... 38
2.10.8 AT/ATX Mode Selection ................................................................................. 39
2.11 MOUNTING THE SYSTEM ........................................................................................ 40
2.11.1 Wall Mounting................................................................................................ 41
2.11.2 In-wall Mounting............................................................................................ 43
2.11.3 Arm Mounting ................................................................................................ 46
2.12 BOTTOM PANEL CONNECTORS................................................................................ 47
2.12.1 LAN Connection............................................................................................. 47
2.12.2 Serial Device Connection .............................................................................. 48
2.12.3 USB Device Connection................................................................................. 49
3 RFID READER............................................................................................................ 51
3.1 INTRODUCTION......................................................................................................... 52
3.2 INSTALLATION.......................................................................................................... 52
3.3 RF320 INTERFACE OVERVIEW.................................................................................. 55
3.4 SERIAL PORT (COM) SETTINGS ............................................................................... 56
3.5 RF320 COMMANDS.................................................................................................. 57
3.5.1 Read Block....................................................................................................... 57
3.5.2 Write Block....................................................................................................... 59
3.5.3 Set Mifare Parameter....................................................................................... 60
3.5.4 Get Mifare Parameter...................................................................................... 61
3.5.5 Set RF320 Mode............................................................................................... 62
4 SYSTEM MAINTENANCE ....................................................................................... 65
4.1 SYSTEM MAINTENANCE INTRODUCTION.................................................................. 66
4.2ANTI-STATIC PRECAUTIONS...................................................................................... 66
4.3 TURN OFF THE POWER.............................................................................................. 67
4.4 REMOVING THE REAR PANEL ................................................................................... 67
4.5 REPLACING COMPONENTS........................................................................................ 68

ACT-412A-N270 User Manual
Page vi
4.5.1 CF Card Replacement...................................................................................... 68
4.5.2 SO-DIMM Module Replacement...................................................................... 69
4.5.3 Wireless Module Replacement ......................................................................... 70
4.5.4 Motherboard Replacement............................................................................... 71
5 BIOS.............................................................................................................................. 72
5.1 INTRODUCTION......................................................................................................... 73
5.1.1 Starting Setup................................................................................................... 73
5.1.2 Using Setup...................................................................................................... 73
5.1.3 Getting Help..................................................................................................... 74
5.1.4 Unable to Reboot After Configuration Changes.............................................. 74
5.1.5 BIOS Menu Bar................................................................................................ 74
5.2 MAIN........................................................................................................................ 75
5.3ADVANCED............................................................................................................... 76
5.3.1 CPU Configuration.......................................................................................... 77
5.3.2 IDE Configuration........................................................................................... 78
5.3.2.1 IDE Master, IDE Slave ............................................................................. 79
5.3.3 Super I/O Configuration .................................................................................. 84
5.3.4 Hardware Health Configuration...................................................................... 86
5.3.5 Power Configuration ....................................................................................... 89
5.3.6 ACPI Configuration......................................................................................... 90
5.3.7 APM Configuration.......................................................................................... 91
5.3.8 Remote Access Configuration.......................................................................... 93
5.3.9 USB Configuration........................................................................................... 97
5.4 PCI/PNP................................................................................................................... 98
5.5 BOOT...................................................................................................................... 101
5.5.1 Boot Settings Configuration........................................................................... 102
5.5.2 Boot Device Priority...................................................................................... 104
5.5.3 Hard Disk Drives........................................................................................... 105
5.5.4 Removable Drives.......................................................................................... 106
5.5.5 CD/DVD Drives............................................................................................. 106
5.6 SECURITY............................................................................................................... 107
5.7 CHIPSET ................................................................................................................. 108
5.7.1 Northbridge Configuration............................................................................ 109
5.7.2 Southbridge Configuration .............................................................................112

ACT-412A-N270 User Manual
Page vii
5.8 EXIT........................................................................................................................113
A EXTERNAL CONNECTOR PINOUTS..................................................................115
A.1 INTRODUCTION.......................................................................................................116
A.2 DIGITAL I/O CONNECTOR.......................................................................................116
A.3 EXTERNAL SATACONNECTOR...............................................................................116
A.4 LAN CONNECTOR..................................................................................................117
A.5 POWER CONNECTOR...............................................................................................117
A.6 SERIAL PORT CONNECTOR (COM1).......................................................................118
A.7 SERIAL PORT CONNECTOR (COM3).......................................................................118
A.8 USB CONNECTORS.................................................................................................118
B SAFETY PRECAUTIONS........................................................................................119
B.1 SAFETY PRECAUTIONS........................................................................................... 120
B.1.1 Anti-static Precautions .................................................................................. 121
B.2 MAINTENANCE AND CLEANING PRECAUTIONS ...................................................... 121
B.2.1 Cleaning Tools............................................................................................... 122
C BIOS CONFIGURATION OPTIONS..................................................................... 123
C.1 BIOS CONFIGURATION OPTIONS ........................................................................... 124
D WATCHDOG TIMER .............................................................................................. 127
E HAZARDOUS MATERIALS DISCLOSURE ....................................................... 130
E.1 HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS
ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ..................................... 131

ACT-412A-N270 User Manual
Page viii
List of Figures
Figure 1-1: ACT-412A-N270 All-in-One Access Control Terminal...........................................13
Figure 1-2: ACT-412A-N270 Front View......................................................................................15
Figure 1-3: Front View (Faceplate Removed) ............................................................................15
Figure 1-4: ACT-412A-N270 Rear View.......................................................................................16
Figure 1-5: ACT-412A-N270 Bottom View ..................................................................................17
Figure 1-6: CompactFlash® Slot.................................................................................................17
Figure 1-7: ACT-412A-N270 Dimensions (mm)..........................................................................21
Figure 2-1: Rear Panel Retention Screws ..................................................................................27
Figure 2-2: HDD Retention Screws.............................................................................................28
Figure 2-3: CF Card Slot Cover Location...................................................................................29
Figure 2-4: CF Card Installation..................................................................................................29
Figure 2-5: Rear Panel Retention Screws ..................................................................................32
Figure 2-6: Clear CMOS Jumper .................................................................................................34
Figure 2-7: COM1 and COM3 Pin 9 Setting Jumper Locations................................................35
Figure 2-8: COM3 RX Function Select Jumper Location..........................................................37
Figure 2-9: COM3 TX Function Select Jumper Pinout Locations............................................38
Figure 2-10: COM3 RS-232/422/485 Serial Port Select Jumper Location................................39
Figure 2-11: AT/ATX Switch.........................................................................................................40
Figure 2-12: Wall-mounting Bracket...........................................................................................41
Figure 2-13: Chassis Support Screws........................................................................................42
Figure 2-14: Secure the ACT-412A-N270....................................................................................43
Figure 2-15: Cut Foam Tape ........................................................................................................43
Figure 2-16: Attach Foam Tape...................................................................................................44
Figure 2-17: Foam Tape Installed................................................................................................44
Figure 2-18: ACT-412A-N270 Panel Opening.............................................................................45
Figure 2-19: Tighten the In-wall Mounting Screws....................................................................45
Figure 2-20: Faceplate Installation..............................................................................................46
Figure 2-21: ACT-412A-N270 Arm Mounting Retention Screw Holes .....................................47
Figure 2-22: LAN Connection......................................................................................................48
Figure 2-23: Serial Device Connector.........................................................................................49

ACT-412A-N270 User Manual
Page ix
Figure 2-24: USB Device Connection.........................................................................................50
Figure 3-1: InstallShield Wizard Welcome Screen....................................................................52
Figure 3-2: Customer Information Screen .................................................................................53
Figure 3-3: Setup Type Selection Screen...................................................................................53
Figure 3-4: Current Settings Confirmation Screen ...................................................................54
Figure 3-5: RF320 COM Port Settings.........................................................................................56
Figure 3-6: Read Block.................................................................................................................58
Figure 3-7: Write Block ................................................................................................................59
Figure 3-8: Set Mifare Parameter ................................................................................................61
Figure 3-9: Get Mifare Parameter................................................................................................62
Figure 3-10: Set RF-320 Mode.....................................................................................................63
Figure 4-1: Rear Panel Retention Screws ..................................................................................68
Figure 4-2: SO-DIMM Socket Location .......................................................................................69
Figure 4-3: SO-DIMM Installation................................................................................................70
Figure 4-4: Wireless Module Location........................................................................................70

ACT-412A-N270 User Manual
Page x
List of Tables
Table 1-1: ACT-412A-N270 System Specifications ...................................................................20
Table 2-1: Jumpers.......................................................................................................................31
Table 2-2: Preconfigured Jumpers .............................................................................................32
Table 2-3: Clear CMOS Jumper Settings....................................................................................33
Table 2-4: COM1 Pin 9 Setting Jumper Settings.......................................................................34
Table 2-5: COM3 Pin 9 Setting Jumper Settings.......................................................................35
Table 2-6: RS-422 Pinouts ...........................................................................................................35
Table 2-7: RS-485 Pinouts ...........................................................................................................36
Table 2-8: COM3 RX Function Select Jumper Settings............................................................36
Table 2-9: COM3 TX Function Select Jumper Settings.............................................................37
Table 2-10: COM3 RS-232/422/485 Serial Port Select Jumper Settings..................................39
Table 3-1: RF320 COM Port Settings..........................................................................................56
Table 3-2: Read Block Raw Data Format....................................................................................58
Table 3-3: Read Block Response Format...................................................................................58
Table 3-4: Write Block Raw Data Format ...................................................................................60
Table 3-5: Write Block Response Format ..................................................................................60
Table 3-6: Set Mifare Parameter Raw Data Format ...................................................................61
Table 3-7: Set Mifare Parameter Response Format ..................................................................61
Table 3-8: Get Mifare Parameter Raw Data Format...................................................................62
Table 3-9: Get Mifare Parameter Response Format..................................................................62
Table 3-10: Set RF320 Mode Raw Data Format .........................................................................64
Table 3-11: Set RF320 Mode Response Format ........................................................................64
Table 5-1: BIOS Navigation Keys................................................................................................74

ACT-412A-N270 User Manual
Page xi
BIOS Menus
BIOS Menu 1: Main.......................................................................................................................75
BIOS Menu 2: Advanced..............................................................................................................76
BIOS Menu 3: CPU Configuration...............................................................................................77
BIOS Menu 4: IDE Configuration.................................................................................................78
BIOS Menu 5: IDE Master and IDE Slave Configuration...........................................................79
BIOS Menu 6: Super I/O Configuration.......................................................................................84
BIOS Menu 7: Hardware Health Configuration..........................................................................86
BIOS Menu 8: APM Configuration...............................................................................................89
BIOS Menu 9: General ACPI Configuration ...............................................................................90
BIOS Menu 10: APM Configuration.............................................................................................91
BIOS Menu 11: Remote Access Configuration..........................................................................93
BIOS Menu 12: USB Configuration.............................................................................................97
BIOS Menu 13: PCI/PnP Configuration.......................................................................................99
BIOS Menu 14: Boot.................................................................................................................. 101
BIOS Menu 15: Boot Settings Configuration.......................................................................... 102
BIOS Menu 16: Boot Device Priority Settings ........................................................................ 104
BIOS Menu 17: Hard Disk Drives ............................................................................................. 105
BIOS Menu 18: Removable Drives........................................................................................... 106
BIOS Menu 19: CD/DVD Drives ................................................................................................ 107
BIOS Menu 20: Security............................................................................................................ 107
BIOS Menu 21: Chipset............................................................................................................. 109
BIOS Menu 22: Northbridge Chipset Configuration............................................................... 109
BIOS Menu 23:Southbridge Chipset Configuration............................................................... 112
BIOS Menu 24:Exit..................................................................................................................... 113

ACT-412A-N270 User Manual
Page 12
Chapter
1
1 Introduction

ACT-412A-N270 User Manual
Page 13
1.1 ACT-412A-N270 All-in-One Access Control Terminal
Figure 1-1: ACT-412A-N270 All-in-One Access Control Terminal
The ACT-412A-N270 is 1.6 GHz Intel® Atom™ powered access control terminal with a
RFID reader and a rich variety of functions. The ACT-412A-N270 is designed for easy and
simplified integration in to access control applications.
An Intel® 945GSE graphics memory controller hub (GMCH) coupled with an Intel®
ICH7M input/output controller hub ensures optimal memory, graphics, and peripheral I/O
support. The system comes with 1 GB of preinstalled DDR2 SDRAM and supports a
maximum of 2.0 GB of DDR2 SDRAM ensuring smooth data throughputs with reduced
bottlenecks and fast system access.
Two serial ports and two external USB 2.0 ports ensure simplified connectivity to a variety
of external peripheral devices. Wi-Fi capabilities and two RJ-45 Ethernet connectors
ensure smooth connection of the system to an external LAN.
1.1.1 Features
The ACT-412A-N270 features the following:
12.1” TFT LCD with resistive type touch screen

ACT-412A-N270 User Manual
Page 14
1.6 GHz Intel® Atom™ CPU with 512 KB L2 cache preinstalled
Built-in RFID reader supports Mifare card and EM card read/write
Preinstalled 1 GB DDR2 memory module
802.11 b/g wireless module
One RS-232 port and one RS-232/422/485 port
Three USB 2.0 ports
CompactFlash® Type II slot
Provides RFID configuration tool to read or write Mifare tags and EM tags
Built-in digital camera and microphone
Built-in 2.0 W stereo speakers
IP 64 compliant front panel
RoHS compliance
1.1.2 Applications
The ACT-412A-N270 is elegant yet sophisticated systems that are easily implemented in
diverse environments including:
Door access
Time attendance
Cashless payment terminal
Parking access control
1.2 External Overview
The stylish ACT-412A-N270 access control terminal comprises of a screen, front and rear
panels. An ABS/PC plastic front frame surrounds the front screen. The rear panel provides
screw holes for a wall-mounting bracket compliant with VESA FDMI standard. An I/O
interface panel on the rear panel provides access to external interface connectors that
include LAN, USB 2.0, serial port, reset button, power connector and power switch.
1.2.1 Front Panel
The front side of the ACT-412A-N270 is a flat panel TFT LCD screen surrounded by an
ABS/PC plastic hard cover. The top of the front panel has a 300K pixel digital camera, two
microphones, a power LED indicator, power button, a USB port, a RFID reader for
Mifare/EM tag and two speakers for stereo sound (Figure 1-2).

ACT-412A-N270 User Manual
Page 15
Figure 1-2: ACT-412A-N270 Front View
Figure 1-3: Front View (Faceplate Removed)

ACT-412A-N270 User Manual
Page 16
1.2.2 RFID Reader
A RFID reader is integrated in the front panel and supports Mifare 13.56 MHz or EM
125 KHz RFID tags. The ACT-412A-N270 also came with a RFID tool to read or write data
on or into the Mifare tags or EM tags. Please refer to Chapter 5 for detailed description of
the RFID tool (RF320).
1.2.3 Rear Panel
The rear panel provides access to retention screw holes that support the VESA 75 and
100 mounting. Refer to Figure 1-4.
Figure 1-4: ACT-412A-N270 Rear View
1.2.4 Bottom Panel
The I/O interface panel located on the bottom panel of the ACT-412A-N270 (Figure 1-5)
has the following I/O interface connectors:
1 x 12 V DC power jack

ACT-412A-N270 User Manual
Page 17
1 x Audio jack
1 x Power switch
1 x External SATA connector
1 x RS-232 port
1 x RS-232 or RS-422/485 port
2 x RJ-45 GbE LAN connectors
2 x USB 2.0 ports
1 x Reset button
The external I/O interface connectors on the rear panel are shown in Figure 1-5.
Figure 1-5: ACT-412A-N270 Bottom View
1.2.5 CompactFlash® Slot
The system can also support a CompactFlash® Type II (CF Type II) memory disk.
Figure 1-6: CompactFlash® Slot

ACT-412A-N270 User Manual
Page 18
1.3 Internal Overview
The ACT-412A-N270 has the following components installed internally:
1 x Motherboard
1 x 1 GB DDR2 SDRAM SO-DIMM
1 x Wireless module
1 x RFID reader
2 x Speakers
1 x Digital camera
2 x Microphones
1.4 Specifications
The ACT-412A-N270 has the following preinstalled components:
1 x Motherboard
1 x TFT LCD screen
1 x Touch screen
1 x Inverter
1 x Wireless LAN module
1 x DDR2 memory module
1 x AT/ATX switch
The following section lists the system specifications. The technical specifications for some
other preinstalled components are shown in the Appendix A.
1.4.1 System Specifications
The technical specifications for the ACT-412A-N270 system are listed in Table 1-1.
Specification ACT-412A-N270
LCD Size 12.1”
Max. Resolution 1024 x 768
Brightness 500 cd/m2
Contrast Ratio 700:1

ACT-412A-N270 User Manual
Page 19
LCD Color 262 K
Pixel Pitch (mm) 0.3075 (H) x 0.3075 (V)
Viewing Angle (H-V) 160 (H) / 160 (V)
Backlight MTBF 60,000 hours
SBC Model AFLMB2-945GSE-N270-R10
CPU 1.6 GHz Intel® Atom™ CPU with 512 KB L2 cache
GMCH Intel® 945GSE + ICH7M
Memory 1 GB DDR2 SDRAM SO-DIMM (system max. 2 GB)
LAN Two Realtek RTL8111CP PCIe GbE Controllers
SSD CF Type II
HDD One 2.5” SATA HDD bay
Watchdog Timer Software Programmable supports 1 sec. ~ 255 sec. system reset
Audio ALC888 HD Audio codec
AMP 2.0 W + AMP 2.0 W (built-in stereo speakers)
Expansion One PCIe Mini card slot (for wireless LAN 802.11 b/g module)
Camera and MIC Built-in 300 K pixel camera and microphone
RFID Supports MIFARE and EM RFID
Construction Material ABS + PC plastic front frame
Aluminum alloy chassis
Front Panel Color Blue and White
Mounting Panel, Wall, Stand or Arm (VESA 75 x 75 mm, 100 x 100 mm)
Dimensions (W x H x D)
(mm) 244.69 x 251.72 x 53.3
Operation Temperature -10ºC ~ 50ºC with CF card or SSD SATA HDD
0ºC ~ 45ºC with SATA HDD
Net weight 2.842 kg
IP level (front panel) IP 64
EMC CE and FCC
Safety CB and CCC

ACT-412A-N270 User Manual
Page 20
Touch Screen 5-wire resistive type
Power Adapter 12 V DC output, 100 ~ 264 V AC, 50/60 Hz input (60 W max)
Power Consumption 38 W
I/O Ports and Switches
(Rear Panel)
One 12 V DC power jack
One Power switch
One 6-pin terminal block for signal input (2 x Digital Input, 2 x
Digital Output)
One eSATA port
One Audio line-out jack
One RS-232 COM port
One RS-232/422/485 COM port
Two RJ-45 GbE LAN connectors
Three USB 2.0 ports (one on front panel)
One Reset button
Table 1-1: ACT-412A-N270 System Specifications
1.5 Dimensions
The dimensions of the ACT-412A-N270 are shown in Figure 1-7 and listed below.
Width: 244.69 mm
Height: 251.72 mm
Depth: 53.3 mm