IEI Technology PPC-5020 User manual

PPC-5020
12.1”TFT Panel PC
(Ver 2.0)

1
Copyright Notice
©Copyright 2002 by ICP Electronics Inc. All Rights Reserved.
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the
part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
Trademarks
PPC-5020 is a registered trademark of ICP Electronics Inc. IBM PC is a registered
trademark of International Business Machines Corporation. Intel is a registered
trademark of Intel Corporation. Other product names mentioned herein are used for
identification purposes only and may be trademarks and/or registered trademarks of
their respective companies. If you have any questions or need other information,
please visit to our web site.
http://www.iei.com.tw

2
Table of Contents
1. Introduction................................................................................. 3
1.1 Checklist ....................................................................... 3
1.2 Features......................................................................3-4
1.3 Specifications.............................................................4-5
1.4 Dimensions ................................................................... 6
2. System Setup............................................................................... 7
2.1 Assembly Diagram.....................................................7-9
2.2 POS-566/370 CPU Board Installation ........................ 10
2.3 Power Supply Installation......................................... 11
2.4 Drive Disk Installation......................................... 12-13
2.5 Speakers and Fan Installation ................................... 14
2.5 Panel Mounting......................................................... 15
2.6 Wall Mounting.......................................................... 16
2.7 Arm Mounting .......................................................... 17
2.8 Rack Mounting.......................................................... 18
Appendix A. Power Supply.......................................................... 19
Appendix B. Display Interface ................................................19-20
Appendix C. Control Panel Interface…………………………… 21

3
1Introduction
The PPC-5020, 12.1" high brightness LCD TFT Panel PC takes advantage of modern
flat-panel display technology, coupled with a POS-566/370 CPU board, one hard
drive bay and an integrated power supply to ensure minimum size. It is an IBM
PC/AT compatible computer specially designed to meet the applications in an
industrial environment.
1.1 Checklist
ITEM DESCRIPTION Q’TY NOTES
1 PPC-5020 USERMANUAL 1
2 POWER CORD 1
3 WALL-MOUNT VIBRATION KIT2
4 WALL-MOUNT bracket 1
5 PANEL MOUNT KIT 4
6 SCERW KIT 1
6.1 SCREW BOLT (M4*P0.7*8mm) 4
6.2 Round with washer screw (M3*6)10
6.3 Sink with washer screw（M4*6）8
6.4 Round screw (M5*50)4
6.5 FLAT SCREW (6#32*6) 4
7 KEY WITH HDD 1
8 CF-507 SOKET-370 BLOWER COPPER COOLER 1
9 POS-370 OR POS-566 USER MANUAL 1 OPTION
10 DISK FOR SIS CHIP SET 1
11 MINI JUMPER SOME
12 Y CABLE. (MINI DIM TO MOUSE/KB) 1
13 TOUCH SCREEN DRIVER (option) 1 OPTION
1.2 Features
CPU Board
PPC-5020 is designed for POS-566/370 CPU board. The POS-566/370 board is a
LPX specification board, equipped with a high-performance socket 370 Celeron
Pentium III®CPU, LCD/CRT and 10/100Mbps Ethernet port, designed for system
manufacturers, integrators, or VARs to provide the ultimate in performance, reliability,
and quality.

4
LCD Display
The PPC-5020 is equipped with a high brightness 12.1" TFT LCD.
Power Supply
The PPC-5020 is equipped with a standard ACE-816APS 150W power supply with
PFC.
Touch Screen (option)
Aluminum front panel supports both resistive and capacity touch screens.
Plastic front panel supports a resistive touch screen only.
HDD
The PPC-5020 supportsone 3.5” removable HDD drive bay.
1.3 Specifications
Display Model SANYO
Display Type 12.1” TFT color
LCD model TM121SV-02L11
Resolution SVGA 800x600
Max. Colors Native 262k colors(r/g/b 6 bit each)
Brightness 360 cd/m2high luminance
LCD MTBF 50,000 hrs
Backlight MTBF 30,000 hrs
Nominal input Voltage VDD +3.3V
Support Voltage -0.3V to 4.0V
?? 3M touch resistive type touch screen (option)
Type: Analog Resistive
Resolution: Continuous
Light transmission: Typical value 72%
Surface Hardness: 4H (Test condition: ASTM D3363-92A)
8-wire touch screen
Support driver: Supports DOS, Windows 3.1, 95, 98, NT/Me/2000, WinCE. NET.
?? 3M touch capacitive type touch screen (option)
Type: Analog Resistive
Resolution: Continuous
Light transmission: Typical value 88%

5
Support driver: Supports DOS, Windows 3.1, 95, 98, NT/Me/2000, WinCE. NET.
Please download the capacitive type driver from IEI web site.
?? Environmental specifications
Operating Temperature: 0 ~ 50℃
Relative Humidity: 5~95 %, non-condensing
Vibration: 5 to 17 Hz, 0.1"double-amplitude displacement,
17 to 640 Hz, 1.5 G peak to peak.

6
1.4 Dimensions
Front Panel: 340mm x 260mm x 9mm (WxHxD)
Cabinet: 310mm x 230mm x 99mm (WxHxD)

7
2 System Setup
The PPC-5020, 12.1" LCD TFT Panel PC, is provided complete kit for your operation.
The following sections of this chapter will help your installation and maintenance.
2.1 Assembly Diagram
The Reverse Side of PPC-5020
The diagram shows below the reverse side of PPC-5020. For maintenance,
installation or upgrade, you will need to remove the back cover first by unfastening
the 9 screws as shown in the diagram.
Warning: Before any installation/un-installation, please notice any effects of static
electricity.

8
The Reverse Side of the Rear Cabinet
The following figure shows the reverse side of the rear cabinet.
One HDD and one power supply are accessible for operation on the driver frame.
?? POS-566
?? POS-370

9
The Side View of PPC-5020
On the side panel, you will find one fan and two speakers. Please bear this in mind
when mounting the unit. It is placed in to the cabinet and then fastened by four
screws.
FAN
SPEAKER

10
2.2 POS-566/370 CPU Board Installation
To install the POS-566/370 CPU Board, you have to place the board into the cabinet
and then fasten it by four screws.

11
2.3 Power Supply Installation
The standard Power Supply for PPC-5020 is ACE-816APS, which needs to be
fastened to the power bracket by 2 screws, and to be fastened in the cabinet by
pushing it as far back as possible, as shown in the diagram below.
Input Voltage: 90V to 264VAC
Output rating:
Nominal Regulation Ripple/Noise MIN. MAX.
+3.3V +/-5% 50mV 0.3A 10A
+5V +/-5% 50mV 1.0A 14A
+12V +/-5% 120mV 0.3A 4.2A
-12V +/-10% 120mV 0.0A 0.3A
+5VSB +/-5% 50mV 0A 2.0A
Total Output of +3.3V and +5V may not exceed 85W.
PUSH

12
2.4 Drive Disk Installation
The following sections will inform you how to install the power supply and HDD.
As the power supply and HDD are installed in the cabinet, they are reached by
opening the back cover.

13
HDD Installation
To install the HDD, first fasten the HDD to the HDD cage. Then, push the HDD cage
into the HDD bracket and fix it by key lock.

14
2.5Speakers and Fan Installation

15
2.6Panel Mounting
PPC-5020 is designed for panel mounting. Before mounting the PPC-5020 into
panel, you have to check the cut out dimension first. Then mount it into panel by
four supporters. Please refer to diagrams below.
UNIT:mm
232.0
312.0

16
PPC-5020 is suitable for Wall mount.
153.00
90.00
20.00
22.50
45.00
4-D4.5

17
2.7 Arm Mounting
PPC-5020 is not only suitable for panel and wall mounting but also has 75/100mm
interface pads, making it ideal for arm mounting; and the specification conform to
proposed VESA standards.

18
2.8 Rack Mounting
DM/SRM/PPC serial product provide option rack mount kit for industrial Rack. The
following diagram shows how to mount DM/SRM serial product onto the 19" Rack.
Rackmount-Kit
STEP 1
STEP 2

19
AppendixA Power Supply
Industrial Power Supply:ACE-816APS series Power Supply
High reliability triple output switching Power Supply (just 40.6mm in height)
Standard Power Supply: ACE-816APS
Efficiency: 68% min
PROTECTION: Over Voltage/Load protection and short circuit protection
Operating temperature:0°C to 50°C
Vibration: 5~17Hz, 0.1” double amplitute displacement.
17~640Hz, 1.5G acceleration peak to peak.
Shock: 10G for 11ms once on each X, Y, and Z-axis
Safety: -UL1950
-TUV EN60950 OR VDE EN60950
-CSA 22.2 NO.234 LEVEL3
-IEC 950
-CE
-NEMKO EN 60950
EMI:-FCC 15 Subpart J,class B Vac operation.
-CISPR 22 CLASS ‘B’230 Vac operation.
Power connector: ATX
Built-in ball bearing fan.
Warning: Whenever you need to take off a part for either maintenance or
upgrading purpose, you should switch off the power supply and unplug the
power cord first.