Igloohome Deadbolt 2S Installation and maintenance instructions

Installers &
User guide
Deadbolt 2S.
Version 0.2 05/18

As our igloohome app is frequently updated, there may
be changes to this manual. Please refer to our website
igloohome.co/support for the latest version of the manual.

Table of Contents
04 What’s Included
05 Specifications
06 Requirements
07 Lock Anatomy
08 Prepare Door for Installation
10 Prepare Lock for Installation
11 Installation Instructions
18 Test Lock
19 Prepare the Door Frame
21 Features
22 Unlocking
23 Locking
20 Pairing
24 Lock Tutorial
27 Lock Behaviour
28 Troubleshoot

What’s Included
Front Assembly
& Rubber Gasket
Back Assembly
Rubber Gasket
Back Assembly
AA Alkaline Batteries x4
Bolt Assembly
Keys x5
Screw Holder
Back Plate
Strike Plate Housing &
Strike Plate
Drill Sheet
43mm (1-11/16”)
Bolt Screw x3
5mm (13/64”)
Bolt Screw x2
15mm (19/32”)
Wood Screw x4
04
8mm (5/16”)
Bolt Screw x2
20mm (25/32”)
Bolt Screw
Door Sensor & Magnet

Specifications
Model igloohome Smart Deadbolt 2S
Material Zinc Alloy, ABS
Current Rating (Standby) ~30uA
Current Rating (Active) ~200mA
Batteries 4 x AA Alkaline (Non - Rechargeable)
Unlock Mechanism Bluetooth, PIN code, Physical Keys, Thumbturn
Front BackSide
145mm (5-11/16”)
60mm (2-23/64”) 11mm (7/16”) 51mm (2-1/64”) 64.5mm (2-35/64”)
160mm (6-19/64”)
05

Requirements
20mm
(25/32”)
35mm (1-3/8”)
to
60mm (2-3/8”)
50 mm (2”) 10 mm
(25/64”)
144.5mm (5-11/16”)
>110mm (4-21/64”) for 60mm (2-3/8”) backset
or
>120mm (4-23/32”) for 70mm (2-3/4”) backset
06
Door Thickness
Recommended
Gate Clearance Door Edge Clearance
10 mm (25/64”) 10 mm
(25/64”)
160mm (6-19/64”)
Height Clearance
9V Battery Clearance

Lock Anatomy
Outer Body
Touch Screen
Keypad
Key hole Cover
(Remove cover
to access
physical key
unlock)
9V Jumpstart
Thumbturn
Privacy
Lockout Button
07
Battery Cover
Release
Battery Cover

* Please ensure that there is an existing handle on your door for push - pull access.
* Not for: metal gates, glass doors or sliding doors.
If you are unsure if your door is suitable, send us web links to your door pictures to
Prepare Door for Installation
Items needed:
Recommended
Door and door frame material : Wood
Recommended
Gap between door and door frame: <3mm (1/8”)
DrillDrill Sheet 10mm (25/64”)
Drill Bit
54mm (2-1/8”)
Hole Saw
25mm (1”)
Spade Bit
#2 Phillips Screw Driver 20mm (25/32”)
Chisel
Hammer
[email protected]
08

How to use the Drill Sheet
* Mark the center of the holes and then drill for accuracy.
Drilling (Door)
Make sure this is
aligned to the centre
of door edge
Door edge
Fold here
before drilling
holes for side
Chiselling
Depth:
4.5mm (11/64”)
or until bolt
assembly plate
is flush against
door
Put the bolt tongue in &
chisel around the edge
09
54mm (2-1/8”)
Hole Saw
25mm (1”)
Spade Bit
20mm
(25/32”)
Chisel
20mm (25/32”)
Chisel

Prepare Lock For Installation
Set Back Assembly for Left / Right Installation
Remove Battery Cover from the Back Assembly
LR
Press the button on the
top of the battery cover,
and pull outwards.
L R
10
Set the toggle to ‘R’ for
right-side installation.
Right Installation
Set the toggle to ‘L’ for
left-side installation.
Left Installation
Top View of Battery Cover

Installation Instructions
Measure
If you are replacing your current deadbolt lock, industry standards are 60mm (2-3/8”) or 70mm
(2-3/4”) backset. To determine which backset length you should use, so measure the distance (x)
between the center of 54mm (2-1/8”) hole to door edge.
Prepare bolt assembly based on the distance (x)
Bolt ships with bolt assembly in 60mm (2-3/8”) position. If required, twist the bolt and pull to
extend (simultaneously) to 70mm (2-3/4”) backset position.
Twist upwards
Pull
Twist downwards
to lock backset position
X
54mm
(2-1/8”)
Hole
11

Insert bolt and front assembly into door edge
The ‘+ ‘ hole on the backset should be in the middle of the hole.
Screw Holder
Screws
15mm (19/32”)
Secure the Front Assembly using the Back Plate.
To do this, place the Back Plate (ensuring the correct side placement).
Follow this orientation
12
c
c
Please ensure that tailpiece is in vertical position.

Screw it to the Front Assembly using the three 40mm (1-37/64”) screws.
13
Screws
43mm (1-11/16”)
Door Sensor Installation
Adjust the position of the door sensor according to the door handling (left or right installation).
Use the 2 x 5 (13/64) mm screws to secure the door sensor to the back plate.
Screws
5mm (13/64”)
Right InstallationLeft Installation
e
dd
d
d
e
e
e
e

Fit in the Rubber Gasket
Insert the front assembly cable through the rectangular hole on the rubber gasket.
The hole should be on the right side of the rubber gasket.
5
Assembly Cable
14
Door Sensor Cable
goes through the
arched hole on the
Rubber Gasket
Right InstallationLeft Installation

Connect Assembly Cable
Connect the sensor cable to the Back Assembly then connect the assembly cable from
the Front assembly through the 54mm hole to the Back Assembly. Ensure that the wire is
installed properly and securely.
LR
6
7Fit Back Assembly to the Door Tailpiece
Left Installation Right Installation
Ensure thumbturn position is turned to ‘unlock’ position.
Thumbturn
is in vertical
position
Thumbturn is
in horizontal
position
15
Door Sensor
Cable
Assembly
Cable

Before closing the battery case lid.
Insert 4 AA Alkaline Batteries
Secure the Back Assembly
Screws
8mm (5/16”)
20mm (25/32”)
8
16

17
Side View
Push the battery case lid inwards to close.
Close the battery case lid

Still experiencing issues?
Test Lock
Place hand over your lock to activate touchpad and hold # to lock.
Does your bolt lock?
Yes No
Congrats!
Your lock is correctly installed.
Proceed to next steps.
Bummer!
Does the bolt lock and unlock
when you turn the thumbturn?
Yes
Left-Right toggle
incorrectly set
No
Tailpiece and/or thumbturn
incorrectly set
Troubleshoot: Try Setting the
left-right toggle on your back
assembly to the correct side.
(See Pg. 10)
Troubleshoot: Dissemble lock
and install it again.
Go to igloohome.co/support for more help
18

Prepare the Door Frame
Ensure to align the lock to the door frame
and mark it down.
Same height
Door
Frame
Mark out where the bolt tongue locks then
drill a corresponding hole on door frame.
Chisel to fit the strike plate in as well.
Mark & Drill Hole
Secure strike plate housing and strike plate using 2x 25mm (1”) wood screws.
1mm
(11/64”)
19
25mm (1”)
Spade Bit
20mm (25/32”)
Chisel
26mm
(1-1/32”)
58mm
(2-9/32”)

Deadbolt 2S
__________
2.1 Enter your lock name > Confirm > Create new home or Add lock to existing
Home > Name Your Home > Submit > Successfully Added!
Pairing
Download igloohome app
from App Store/Google Play
Register a new
account or,
Login with an existing
account on app
CHECKLIST
Lock has not been paired
New users
1. Upon Login > Add a new igloohome lock >Select your Product >Pair Lock to App >Next
The keypad stays awake during pairing
Turn on your phone’s Bluetooth
and Internet connection
2. Enter your lock name > Confirm > Create New Home > Name Your Home > Submit >
Successfully Added!
Deadbolt 2S
__________
1. Go to Menu > Configuration > Add Lock > Select your Product > Follow Steps for
Pairing Lock To App > Select Bluetooth Lock > Lock Paired!
Current users
2. Add lock to a new or existing home.
20