iLoq F50S.2x1.HZ User manual

Document ID
270443
05/2023
Rev 1.0
iLOQ Oy
www.support.iloq.com
Key Tube Cylinder
User Guide
F50S.2x1.HZ
F50S.3x1.HZ/SD
F50S.4x1.HZ/SD
F50S.5x1.HZ/SD
F50S.611.SB

1. Contents ................................................................................................................. 2
2. Safety Information.................................................................................................. 3
2.1 Safety signs .................................................................................................... 3
3. Overview ................................................................................................................. 3
4. Care and Maintenance .......................................................................................... 3
5. Installation of the iLOQ F50S Key Tube Lock Cylinder ....................................... 4
5.1 Compatible Key Tubes.................................................................................. 4
6. Replacing the Reader Knob .................................................................................. 5
7. After installation ..................................................................................................... 6
8. Instructions for use................................................................................................. 6
8.1 Open the key tube......................................................................................... 7
8.2 Lock the key tube .......................................................................................... 8
9. Disposal of Decommissioned Products ............................................................... 9
10. Compliance ............................................................................................................ 10
1. Contents
2
Key Tube Cylinder
User Guide
Key Tube Cylinder

2. Safety Information
2.1 Safety signs
Sign Description
General notice sign. Indicates particularly important
information about the installation and deployment.
Read these instructions carefully before using products.
This information is to ensure your safety and long
lifetime of the products.
3. Overview
The iLOQ F50S Key Tube Lock Cylinders are battery-free programmable electromechanical key tube lock
cylinders for the iLOQ S50 locking system.
Two different Reader Knob lengths are available, short and long. In the product code (e.g. F50S.2x1.HZ),
replace “x” with 1 = short reader or 2 = long reader.
4. Care and Maintenance
• The instructions should be carefully followed during installation and use. These instructions and any
maintenance instructions should be passed on by the installer to the user.
• The iLOQ F50S Key Tube Lock Cylinders must be installed and used carefully without excessive force.
• Do not drop the product.
• The product should not be modified in any way except in accordance with the modifications
described in these instructions.
• Due to the integrated spring operated locking bolt the F50S Key Tube Lock Cylinder is self-locking,
use with care.
• The product is designed to be maintenance-free. It does not require any regular maintenance.
3
Key Tube Cylinder
User Guide
Key Tube Cylinder

5. Installation of the iLOQ F50S Key Tube Lock Cylinder
To conform with local requirements, use locally approved key tubes (please note: the key tube is not
included in delivery).
Mount the key tube according to the tube manufacturer’s instructions. To ensure reliable operation of the
F50S Key Tube Lock Cylinder make sure that the tube is at a 4 degree angle to prevent water pooling inside
and the key tube is mounted max. 5mm inside the wall surface.
In case an existing key tube is mounted too deep inside the wall and the F50S Key Tube Lock Cylinder
cannot be placed in the key tube, it is possible to replace the Reader Knob with a longer version. (See
Section 6 for replacing the Reader Knob).
See the correct positioning of the F50S Key Tube Lock Cylinder inside the tube from the following image
5.1 Compatible Key Tubes
The following key tubes are compatible with F50S Key Tube Lock Cylinder:
Product: Diameter: Key Tube:
• F50S.2x1.HZ • 45 mm • AssaAbloy 390877-100-055
• F50S.3x1.HZ • 38 mm • Kruse 530000, 530010, 530002
• F50S.4x1.HZ • 65 mm • AssaAbloy KD209, KD210
• F50S.5x1.HZ • 38 mm • AssaAbloy KD201, KD201X, KD205, KD207
• F50.611.SB • 78 mm • Assa Mini Safe 9M37
Please verify the compatibility of the key tubes beforehand.
4°
3-5mm
4
Key Tube Cylinder
User Guide
Key Tube Cylinder

6. Replacing the Reader Knob
The Reader Knob may need to be replaced if the length of the original knob is not suitable for the
installation environment or the knob is damaged.
Product: Order code:
• Reader for Key Tube Cylinder, Short • AF50.1
• Reader for Key Tube Cylinder, Long • AF50.2
1. Loosen the screw on the Reader Knob. Use a T10 (torx) tool.
2. Pull the Reader Knob off the neck.
5
Key Tube Cylinder
User Guide
Key Tube Cylinder

3. Slide the new Reader Knob onto the neck so that the screw hole is facing the same direction as the
two knob adjustment slots in the neck.
4. Tighten the screw to a torque of 1.5 Nm. Use a T10 (torx) tool.
7. After installation
Make sure that you have installed all components necessary for the specific installation.
Open and close the F50S Key Tube Lock Cylinder to test the cylinder functionality after installation.
8. Instructions for use
The F50S Key Tube Lock Cylinder needs to be initially programmed with a PC and an iLOQ P55S.1
Programming Key. See separate instructions for programming from the P55S.1 Programming Key
user guide.
Make sure the gap between the Reader
Knob and the body of the lock cylinder
is approx. 1 mm. If not, the weather
protection sealings will not function
correctly.
Make sure that the head of the screw
goes into the hole completely. If head of
the screw is visible it indicates that the
screw is not fully inserted.
6
Key Tube Cylinder
User Guide
Key Tube Cylinder

8.1 Open the key tube
1. Hold a valid key against the lock Reader Knob and wait until the key shows a green light.
2. Turn the Reader Knob to unlock the F50S Key Tube Lock Cylinder.
3. Pull out the F50S Key Tube Lock Cylinder with both hands to prevent the lock cylinder from rotating
uncontrollably.
Note! Due to large variety of NFC enabled
phone models and operating system versions,
iLOQ cannot guarantee that all NFC-enabled
phones will work seamlessly with our locks.
Before using the locks, please check the
location of the NFC antenna in your phone
to know the best position to hold the phone
against the Reader Knob.
After 5 to 15 seconds, the cylinder will
automatically be locked. When the cylinder
is locked, the iLOQ Reader Knob cannot be
rotated.
Due to the spring operated locking bolt the
cylinder is self-locking. Before removing the
cylinder completely from the key tube, take
hold of the cylinder body with your other
hand to prevent it rotating uncontrollably.
Turn the Reader Knob to the neutral position
in a controlled manner when completely
removed.
7
Key Tube Cylinder
User Guide
Key Tube Cylinder

8.2 Lock the key tube
1. Hold a valid key against the lock Reader Knob and wait until the key shows a green light.
2. Turn the Reader Knob to unlock the F50S Key Tube Lock Cylinder.
3. Insert F50S Key Tube Lock Cylinder into the key tube.
After inserting the cylinder completely
back into the key tube, turn the knob
back to the neutral position with your
hand in a controlled manner.
Note! Due to large variety of NFC
enabled phone models and operating
system versions, iLOQ cannot guarantee
that all NFC-enabled phones will work
seamlessly with our locks.
Before using the locks, please check the
location of the NFC antenna in your phone
to know the best position to hold the
phone against the Reader Knob.
8
Key Tube Cylinder
User Guide
Key Tube Cylinder

9. Disposal of Decommissioned Products
Never discard an electrical appliance in household waste. Follow
the local laws and regulations for safe and environmentally friendly
product disposal.
Before discarding products, bear in mind that most iLOQ products
are reusable. All programmable products can be reset to factory
settings, after which they can be reused in another system.
Recycling instructions of decommissioned products are depicted below.
Decommisioned product Sorting
Decommissioned iLOQ fittings, mounting accessories and thumb
turn knobs can be recycled as scrap metal.
Decommissioned iLOQ products containing electronics and circuit
boards, such as iLOQ Lock Cylinders, keys, net bridges, door
modules, key and RFID readers, and relay cards, must be recycled
at an electrical and electronic equipment collection point.
iLOQ products containing batteries and accumulators, such as key
fobs, programming keys and clock circuits, should be recycled at a
regional collection point for batteries and small accumulators.
Most iLOQ packaging materials are suitable for cardboard and
plastic recycling.
9
Key Tube Cylinder
User Guide
Key Tube Cylinder

10. Compliance
The products mentioned inside this user guide are in conformity with the requirements of the directives
declared on this page.
CE
SIMPLIFIED EU DECLARATION OF CONFORMITY:
Hereby, iLOQ Oy declares that the radio equipment type H50S Padlocks are in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
https://www.iloq.com/en/company/patents-and-approvals/
Communication standard: NFC 13,56 MHz Load modulation (ASK) ISO/IEC 14443A, no transmitter.
FCC
Chapter 1, Subpart A, Part 2 of Title 47 of the Code of Federal Regulations
The conformity was assessed in accordance the following standard:
FCC - FCC Rule Part 15
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
ISED
Innovation, Science and Economic Development Canada (ISED)
The conformity was assessed in accordance the following standard:
ISED - ICES 003, Issue 7: 2020 - class B
10
Key Tube Cylinder
User Guide
Key Tube Cylinder

UKCA
Hereby, iLOQ Oy declares that the radio equipment type H50S Padlocks are in compliance with the UK
relevant statutory requirements. The full text of the declaration of conformity is available at the following
internet address: https://www.iloq.com/en/company/patents-and-approvals/
11
Key Tube Cylinder
User Guide
Key Tube Cylinder

iLOQ
www.support.iloq.com
Elektroniikkatie 10
90590 Oulu
Finland
Key Tube Cylinder
User Guide
F50S.2x1.HZ
F50S.3x1.HZ/SD
F50S.4x1.HZ/SD
F50S.5x1.HZ/SD
F50S.611.SB