iLoq H50S.31.HC Series Installation guide

iLOQ Oy • Oulu, Finland • www.iLOQ.com • iLOQ is registered trademark of iLOQ Oy •
©2018 iLOQ Oy. All Rights Reserved •
H50S.x31.HC
H50S.x41.HC
PADLOCK
MOUNTING- AND CARE INSTRUCTIONS

iLOQ Oy • Oulu, Finland • www.iLOQ.com • iLOQ is registered trademark of iLOQ Oy •
©2018 iLOQ Oy. All Rights Reserved •
TABLE OF CONTENTS
1. BEFORE INSTALLATION .................................................................. 3
2. AFTER INSTALLATION ..................................................................... 3
3. CARE .................................................................................................. 3
4. INSTALLATION OF ILOQ H50S ........................................................ 4
5. OPERATING INSTRUCTIONS OF iLOQ H50S .................................. 4
5.1. OPENING ...................................................................................... 4
5.2. CLOSING ...................................................................................... 7
5.2.1. Locking manually (H50S.x41 versions) ................................ 7
5.2.2. Locking with key (H50S.x31 versions) ................................. 8
6. REPLACING THE READER KNOB ................................................. 10
7. GENERAL NOTES ........................................................................... 11
8. DECLARATION OF CONFORMITY ................................................. 11

iLOQ Oy • Oulu, Finland • www.iLOQ.com • iLOQ is registered trademark of iLOQ Oy •
©2018 iLOQ Oy. All Rights Reserved •
1. BEFORE INSTALLATION
1. The instructions should be carefully followed during installation. These instructions and any
maintenance instructions should be passed on by the installer to the user.
2. iLOQ H50S padlock must be installed and used carefully without excessive force.
3. Do not drop the product.
4. The product should not be modified in any way except in accordance with the modifications
described in these instructions.
5. Care should be taken to ensure that any seals or weather-stripping fitted to the complete door
assembly, does not inhibit the correct operations of the key tube cylinder.
6. Care should be taken to ensure that no projection of the D50S cylinder and associated parts, can
prevent the door swinging freely.
7. No liability is accepted for damage to the doors or components due to incorrect installation.
8. We reserve the right to make modifications or further technical developments without further
notice.
9. If there are any deviations from the contents in foreign language versions of the documentation,
the English original shall apply in case of doubt.
2. AFTER INSTALLATION
Test the padlock functionality after installation to ensure that it does not prevent the lock application
from working properly.
3. CARE
The product is designed to be maintenance-free. It does not require any regular maintenance.

iLOQ Oy • Oulu, Finland • www.iLOQ.com • iLOQ is registered trademark of iLOQ Oy •
©2018 iLOQ Oy. All Rights Reserved •
4. INSTALLATION OF ILOQ H50S
Not applicable, for operating instructions see chapter 5.
5. OPERATING INSTRUCTIONS OF iLOQ H50S
Please note: Due to the large variety of Android phone models and operating system
versions, iLOQ cannot guarantee that all NFC-enabled Android phones will work
seamlessly with our locks.
Before using the locks, please check the location of the NFC antenna in your phone so that
you know the best position to hold the phone against the lock-reader knob.
5.1. OPENING
Key Fob (left picture):
Place the Key Fob (with valid access rights) in the middle of the black knob, as shown on the
picture above and below, and wait until the key shows a green light.
Mobile phone (right picture):
Place the NFC aerial in the middle of the knob, as shown on the picture below. The NFC aerial
inside the Mobile phones can be placed in different areas, please check the datasheets from the
mobile phone manufacturer.

iLOQ Oy • Oulu, Finland • www.iLOQ.com • iLOQ is registered trademark of iLOQ Oy •
©2018 iLOQ Oy. All Rights Reserved •
1. Present a valid key to the reader knob and wait until the key shows a green light to
indicate that the lock is open. Valid key could be Android mobile device with iLOQ
app and NFC capability or iLOQ key Fob.
2. Turn the reader knob clockwise 180°.

iLOQ Oy • Oulu, Finland • www.iLOQ.com • iLOQ is registered trademark of iLOQ Oy •
©2018 iLOQ Oy. All Rights Reserved •
3. Pull the shackle open.

iLOQ Oy • Oulu, Finland • www.iLOQ.com • iLOQ is registered trademark of iLOQ Oy •
©2018 iLOQ Oy. All Rights Reserved •
5.2. CLOSING
5.2.1. Locking manually (H50S.x41 versions)
1. Close the shackle
2. Turn the reader knob 180° counterclockwise. After turning the knob, it takes from 5 to
15 seconds before lock is in locked.
3. After 5 to 15 seconds ensure the knob is in locked position and door remains closed.

iLOQ Oy • Oulu, Finland • www.iLOQ.com • iLOQ is registered trademark of iLOQ Oy •
©2018 iLOQ Oy. All Rights Reserved •
5.2.2. Locking with key (H50S.x31 versions)
1. Close the shackle.
2. Present a valid key to the reader knob and wait until the key shows a green light to
indicate that the lock is open. Valid key could be mobile device with iLOQ app and
NFC capability or iLOQ Key Fob.

iLOQ Oy • Oulu, Finland • www.iLOQ.com • iLOQ is registered trademark of iLOQ Oy •
©2018 iLOQ Oy. All Rights Reserved •
3. Turn the reader knob 180° counterclockwise.
After turning the knob, it takes from 5 to 15 seconds before lock is in locked
position (depending on the configured lock opening time).
4. After 5 to 15 seconds ensure the knob is in locked position and door remain closed.

iLOQ Oy • Oulu, Finland • www.iLOQ.com • iLOQ is registered trademark of iLOQ Oy •
©2018 iLOQ Oy. All Rights Reserved •
6. REPLACING THE READER KNOB
If the reader knob is e.g. damaged and needs replacement knob, please follow instructions
how to replace the reader knob correctly.
1. Loosen the fixing screw 2. Pull the knob off
3. Before installing the new knob, add slight amount of CRC silicon grease to the knobs IP
gasket.
Insert the new knob on 5. Tighten the fixing screw