ImaxRC B606 AC User manual

Instruction Manual
www.imaxrc.com
Intelligent Balance Charger
06 AC
b6

B606 Pro Intelligent digital balance Charger
Operating Manual
Special features……………………………………………………………………………………….... 01
Performance parameter……………………………………………………………………………… 02
Exterior and accessories……………………………………………………………………………… 02
Key features……………………………………………………………………………………………….. 02
Operang instrucons…………………………………………………………………………..…….03
Warning and error messages……………………………………………………………………….11
Safety messages…………………………………………………………………………………………..12
Aer-sale service and guarantee………………………………………………………………….12
This charger employs an advanced charging calculaon and design which allow mullayer error to be compable. It can
create a safe charging condion and maximum reduce the danger caused by negligence or seng error of user
This item adopt prevalent Synchronous buck & boost converter technology, this makes conversion efficiency up to 90%
Accept all types of R/C baeries: LiPo, Lilo, LiFe, NiMH, NiCd, Pb
Simple and efficient user interface makes operaon easy, with powful funcon and abundant content. Real-me shows
you the baery voltage、charger current、temperature of baeries、capacity of charge/discharger、elapsed me、input
voltage etc., therefore, you can inquire the present state and establish various safety-limited parameters conveniently.
This charger employs an individual-cell-voltage balancer to maintain you pack in balance while charging/discharging.
During the process, it can monitor and balance each cell of the pack individually (Tolerance: +_0.01V)
Accept individual baery charging/discharging, so you can extend the scope of applicaon of the charger. That is equally
useful for the DIY baery.
Various of charging mode to meet different demand: charging-auto/balance charging/fast charging/storage and cyclic
charging etc.
For users convenience it can store and load maximum five data of different baeries. You can establish the data contains
program seng of the baery to charge or discharge connually. Three data can be called out at any me you need and the
process can be executed without program seng.
Perform 1-5 cycles of charge>discharge or discharge>charge connually for NiMH/NiCd refreshing
You can connect a high-precision digital temperature sensor to protect the charger works in a safety temperature. Once
a baery reaches the maximum temperature you set during charge/discharge, the process will be terminated to protect the
baery. This is very important for NiMH/NiCd ( separately purchased temperature sensor)
For technical expert, this charger offers PC based program can analysis the characterisc of the baery by USB port. It
shows a graph of voltage, current, capacity and temperature curves and it also shows the individual voltage of each cell in
the Lithium baery pack.
*Separate purchased program kit(Ev-xxxA series)

This charger employs an advanced charging calculaon and design which allow mullayer error to be compable. It can
create a safe charging condion and maximum reduce the danger caused by negligence or seng error of user
This item adopt prevalent Synchronous buck & boost converter technology, this makes conversion efficiency up to 90%
Accept all types of R/C baeries: LiPo, Lilo, LiFe, NiMH, NiCd, Pb
Simple and efficient user interface makes operaon easy, with powful funcon and abundant content. Real-me shows
you the baery voltage、charger current、temperature of baeries、capacity of charge/discharger、elapsed me、input
voltage etc., therefore, you can inquire the present state and establish various safety-limited parameters conveniently.
This charger employs an individual-cell-voltage balancer to maintain you pack in balance while charging/discharging.
During the process, it can monitor and balance each cell of the pack individually (Tolerance: +_0.01V)
Accept individual baery charging/discharging, so you can extend the scope of applicaon of the charger. That is equally
useful for the DIY baery.
Various of charging mode to meet different demand: charging-auto/balance charging/fast charging/storage and cyclic
charging etc.
For users convenience it can store and load maximum five data of different baeries. You can establish the data contains
program seng of the baery to charge or discharge connually. Three data can be called out at any me you need and the
process can be executed without program seng.
Perform 1-5 cycles of charge>discharge or discharge>charge connually for NiMH/NiCd refreshing
You can connect a high-precision digital temperature sensor to protect the charger works in a safety temperature. Once
a baery reaches the maximum temperature you set during charge/discharge, the process will be terminated to protect the
baery. This is very important for NiMH/NiCd ( separately purchased temperature sensor)
For technical expert, this charger offers PC based program can analysis the characterisc of the baery by USB port. It
shows a graph of voltage, current, capacity and temperature curves and it also shows the individual voltage of each cell in
the Lithium baery pack.
*Separate purchased program kit(Ev-xxxA series)
Special features:


Exterior and accessories
Key features:
:mode selecon/stop/backbuon. Press this key to select in the main menu or backto the main menu and to stop
duringthe process.
:reduce and increase buon,you can browse other concerninginformaon by this buon duringthe charge/discharge
process. When you are sengparameters, press key for reduce,and key for increase.
:select/enter buon,to start workby press it more than 2 seconds.
Performance parameter
Input voltage range DC:11~18V
AC:100~240V
Charge current range 0.1~6.0A
Discharge current range 0.1~2.0A
Charge power limited max.80W
Discharge power limited max.10W
Balance current max.300mA
Balance tolerance 0.01V
Nicd/NiMH baery cell count 1~18cells
Lithium baery types Li-po,Li-ion,Li-Fe
Lithium baery cell count 1~6series
Pbbaery voltage 2-24V
Weight:640g
Dimensions:145x145x56mm
Mode
Esc
Dec./Inc.
Dec. Inc.
Enter
start

    
   
 
    
    
    
  
   
  
  
 
  
 
  
  

Operating instructions:
Main menu
This shows you the type of charger for 2s, press into the main menu aer self
-check OK.
User set program, press key down and key upward for circulatory choose.
Press key into submenu.
Lithium baery program
NiMH baery program
NiCd baery program
Pb baery program
Save data program
Load data program
Enter
start
Enter
start
Mode
Esc Dec.

imaxRC
B606 Pro
USER SET
PROGRAM
PROGRAM SELECT
Li**BATT
PROGRAM SELECT
NiMH BATT
PROGRAM SELECT
NiCd BATT
PROGRAM SELECT
PB BATT
PROGRAM SELECT
SAVE DATA
PROGRAM SELECT
LOAD DATA
Dec.
Mode/Esc
Dec.
Dec.
Mode/Esc
Dec.
Mode/Esc
Dec.
Mode/Esc
Dec.
Mode/Esc
Dec.
Mode/Esc
Dec.
Mode/Esc
Mode
Esc

Inial parameter set up
Tip: please set up correctly in the “user set” menu before into the job
for the first me you use it.
Press key to the first screen on the le, then press key to
enter the into parameter seng menu.
This charger can accept three types of Lithium baeries: LiPo/Lilo/LiFe;
you have to check the baery carefully and set it up correctly, or it will
cause an explosion! (Please refer the table A)
Normally, 10minutes are enough to perceive it correctly. For the
baery of larger capacity, you may reduce the term or use with the
default value.
Enter
Start
Mode
Esc
You can switch at the same level menu by key.Please refer the
detailed flow chart on the le.
Dec./Inc.
When you are willing to alter the parameter value in the program,
press key to make it blink, then change the value with key.
The value will be stored by press key once.
Enter
Start
Enter
Start
Dec./Inc.
This charge can recognize the cell count of Lithium baery automa-
cally at the beginning of charge or discharge process to avoid from
erroneous seng by user. But deeply discharged baery can be
perceived incorrectly. To prevent the error, you can set the me term
to verify the cell count by the processor. (See the screen )
A0
A0
A2
A3 A4
A5
A7
A9
A6
A8
A10
A11
A1
A2
A1

USER SET
PROGRAM
LiPo/Lilo/LiFe
CHK Time 10 min
NiMH Sensitivity
D.Peak Default
NiCd Sensitivity
D.Peak Default
Waste Time
CHG DCHG 5min
NiMH/NiCd/Pb
TricKle 100mA
Safety Timer
ON 120min
Capacity Cut-off
ON 500mAh
Key Beep ON
Buzzer ON
Input Power Low
Cut-off 10.5V
BacK-light
100%
Lilo
V.TYPE 3.6V LiFe V.TYPE 3.3V
USB/Temp Select
Temp Cut-off 80C USB/Temp Select USB Enable
LiPo
V.TYPE 3.7V
Mode/Esc
Enter
Dec.
Inc.
Dec.
Dec.
Inc.
Dec.
Inc.
Dec.
Inc.
Dec.
Inc.
Dec.
Inc.
Dec.
Inc.
Dec.
Inc.
Dec.
Inc.
Dec.
Inc.
Dec.
Inc.
v
Inc.
shows the trigger voltage for automac charge terminaon of
NiMH and NiCd baery( V), the effecve value ranges from 2 to 20mV
per cell. If V is set higher, there is a danger of overcharging the
baery; if it is set lower, there is a possibility of premature of
terminaon. Please refer technical specificaon of the baery. (NiCd:
12mV, NiMH: 7mV)

Tips: if the voltage of charging baery is lower than 2.5V, V may can not be perceived, this will cause a danger of
discharge. You can connect a temperature sensor or use the charger current above 1C to avoid it.
There is a 3-pin port on the le side of the unit. It can be used as a temperature sensor port or USB port, if the port is
assigned as a temp.port, you can use an oponal temperature probe to contact the surface of baery (see the screen )
and you can set the maximum temperature at which the danger should allow baery to reach during charge, once a
baery reaches this value the process will be terminated to protect the baery. When it is selected as an USB port, you can
connect the charger to your PC with an oponal USB cable. This can ulize the oponal soware that can show you the
charge process at PC. (See the screen )
When NiMH or Nicd baery is on the cyclic process of charge/discharge, it can oen become warm. The program insert
a me delay to occur aer each charge and discharge process to allow the baery adequate me to cool down before
being subjected to the next process. (See the screen ) the value ranges from 1 to 60 minutes. If you are not sure, you
can set it over 10minutes.
The charger will automacally supply the trickle funcon to achieve the full charge with out overheang the baery
fast charge has been terminated. You can alter the trickle value when the charger shows you the screen
When you start a charger process, the integral safety mer automacally starts running at the same me. This is
programmed to prevent overcharge the baery. If it proves to be faulty ,or if the teminaon circuit cannot detect the
baery full. shows you this program can be on or off, and you can set the maximum safety me, the value ranges from
10 to 720min.As the same principle, there is maximum-capacity-limited funcon. See , the value ranges from 10 to
20000mAh.
At the screen you can set the audible sounds to be on or off by this program.
When you use the car baery to supply power for charger, screen shows you this program monitors the voltage of
input DC baery. If the voltage drops below the value you set the operaon forcibly terminated to protect the input aery.
You can adjust the brightness of LCD screen at the charger (see )
Please refer the informaon below (chart A), and select the correct parameter for each baery, or it will cause a
serious result!
A3
A4
A5
A7
A9
A6
A8
A10
A11
item Li-Po Li-10 Li-FeNiMH NiCD Pb
Standard voltage
(V/cell)
3.703.60 3.301.20 1.20 2.00
Max. Charge voltage
cut offlevel (V/cell)
4.20 4.10 3.60 1.60 1.60 2.45
Allowable fast
current
≤1C ≤1C ≤4C ≤2C ≤2C ≤0.4C
Min. Discharge voltage
cut offlevel (V/cell)
≥3.00 ≥3.00 ≥2.00 ≥1.00 ≥0.85≥1.75
types


Lithium baeries (Lilo/LiPo/LiFe) program
Press key to the screen on the le, then press key to enter into the parameter
seng menu. You can switch at the same level menu by key. Please refer the detailed
flow chart on the le. When you are willing to alter the parameter value in the program,
press key to make it blink, then change the value with Key. The value will be
stored by pressing key once, and then press key for more than 2 seconds to start
the process.
Mode
Esc
Mode/Esc
Enter
Start
Enter/Start
Enter
Start Enter Start
Enter
Start
Dec./Inc.
Dec./Inc.
“AUTO charging” this is for individual Lithium baery or some special baery pack without
balance port or cell count. The le side of the first line shows the type of baery you
selected at the user seng. The right side of the first line shows you the mode of charge. The
value on the le side of second line sets a charge current and the value on the right side of
second line sets the cells count of the baery. The definion of the following screen is all the
same. (To know how to connect, please refer picture B)
“Balance charging” this is for 2-6cells of Lithium baery with balance port, the baery pack
being charged should have the individual cell connect, and connect it to the individual port
at the right side of charger with a suitable connecon cable that fits with your baery pack.
(See picture B) In this mode, the charging process will be different from ordinary charging
mode. The internal processor of the charger will monitor and control the voltage of each
cell of the baery pack. This can improve the discharging performance of the baery! EV
charger use the opmized calculaon to control the tolerance in the range of +—0.01V!
“Fast charging” select this mode to finish charging process earlier. Principle: When the current
down to 1/5 of the current you set during the CV term, it will stop the process and eliminate
the forcible requirement of the balance precision. (Whether it is been connected to the
balance port), the charging capacity may be a bit smaller than normal charging but the
process me will be reduced.
“Storage mode” this is for charging or discharging Lithium baery not to be used for the me
being. In order to reduce the wastage, you can select this mode to remain the power to 40%
to store. The final voltage are different from the type of the baery, Lilo:3.75V、liPo:3.85V、
LiFe:3.3V.This is an intellecve program, if the voltage of baery at its inial stage is over the
voltage level to storage, the program will start to discharge, and if it is lower, the program
will start to charge automacally. In order to ensure each baery pack meets the demand,
the individual plug of the baery pack should be connected to the individual port of charger.

PROGRAM SELECT
Li** BATT
LiPo CHARGE
2.0A 11.1V(3S)
LiPo BALANCE
2.0A 11.1V(3S)
LiPo FAST CHG
2.0A 11.1V(3S)
LiPo STORAGE
1.0A 11.1V(3S)
LiPo DISCHARGE
1.0A 11.1V(3S)
Dec.
Inc.
Dec.
Inc.
Dec.
Inc.
Dec.
Inc.
Inc.
Dec.

Mode
Esc
Mode
Esc
Mode
Esc
Mode
Esc
Enter
Start
Enter
Start
Enter
Start
Enter
Start
“Discharge mode” theorecally, Lithium baery do not need to discharge, especially deep-discharge. This feature is to
ensure the power wastage of the Lithium baery over 90%, to avoid the overcharge of the individual baery, you should
connect the balance plug of the baery to the charger, and the current may not exceed 1C.
Start to charge/discharge: aer set up the mode menu correctly, press Key for more than 2 seconds to
start the process.
This screen shows the number of cells you set up and the processor detects.
“R” shows the number of cells selected by you at the previous menu. If both
numbers are idencal you can start charging by press buon. If not, press
buon to go back to previous menu, and then carefully check the number
of cells of the baery pack to charge again. If you selected the AUTO mode or
discharge mode, you can pass over this screen directly.
This screen shows the present situaon during charge process.To stop charging
press key once; As you can see in the sketch on le, :for the cells count, :for
the operang mode, CHG=charging at auto mode、BAL=balance charging mode、
FAS=fast charging、STO=storage mode、Dsc=discharge mode; :elapsed me,
:charge/discharge current, :charge/discharge voltage of baery, :capacity of
charge/discharge.
1
1
2
2
3
3
4
4
5
5
6
6

LiPo CHARGE
2.0A 11.1V(3S)
LiPo BALANCE
2.0A 11.1V(3S) R:3SER S:3SER CONFIRM(ENTER)
LI3S 2.0A 12.59V
CHG 022:43 00682
LiPo FAST CHG
2.0A 11.1V(3S)
LiPo STORAGE
1.0A 11.1V(3S)
LiPo DISCHARGE
1.0A 11.1V(3S)
>2S
Enter
Start >2S

According to press key you can inquire the individual voltage of each baeries and final voltage
etc. connually as follow (this need to connect the balance plug):
Dec./Inc.
You can check the individual voltages of each cell in the baery pack while using the
individual connecon cable to the baery.
The final voltage will be reached at the end of process.
You can inquire the safety capacity.
You can inquire the safety me.
You can use the 3-pin port as an USB port or inquire the safety temperature value.
It show you the external temperature when the temperature sensor is connected you can
inquire
This shows the present voltage of input power

4.20 4.20 4.20
0.00 0.00 0.00
End Voltage
AUTO CHK
Capacity Cut-off
ON 5000mAh
Safety timer
ON 120min
USB/Temp Select
Temp Cut-off 80C
EXT.Temp 0C
IN Power VOLTAGE
12.60V
Inc.
Dec.
Dec.
Dec.
Dec.
Dec.

NiMH/NiCd baery program
Press key to the screen on the le, and then press key to into the
submenu. You can switch at the same level menu to select the mode by Key.
Please refer the detailed flow chart on the le. When you are willing to alter the
parameter value in the program, press key to make it blink, then change the
value with key. The value will be stored by pressing key once. Then
press key for more than 2 seconds to start the process. Since the menu of NiMH
is the same as NiCd, there is an example of NiMH only.
“CHARGE” mode the default mode is “AUT”. In “AUT” mode,you need to set the
upper limit of charger current to avoid from higher feeding current that may damage
the baery. Because some baeries of low impedance and small capacity can lead to
the higher charge current by the processor at automac charge mode. But in “Man”
mode, it will charge the baery with the charge current you set at the display. Each
mode can be switched by pressing start/enter key, when the current field is blinking,
press key for more than 1 second.
“DISCHARGE” mode the discharge current ranges from 0,1A to 5.0A and the final
voltage ranges from 0.1 to 5.0A and the final voltage ranges from 0.1 to 25.0V, the
operang method similar as Lithium baery. The final voltage of NiMH baery is
1.0V/Cell, and the NiCd is 0.85V/cell, please refer the recommend by the baery of
manufacturer.
“CYCLE” mode this charger can perform 1-5 cycles of DCHG>CHG or CHG>DCHG
connually. You can select it for the new NI** baery or the long-term placement
NI** baery. Please set up carefully or it will damage the baery! To set the
parameter please follow the previous charge/discharge menu.
Mode
Esc
Enter
start Enter start
Dec./Inc.
Enter
start
Dec./Inc.
Dec./Inc.
Enter
start
Enter
start

PROGRAM SELECT
NiMH BATT
NiMH CHARGE Aut
CUR LIMIT 5.0A
NiMH DISCHARGE
1.0A 11.5V
NiMH CYCLE
DCHG CHG 3
v
Mode/Esc
Enter/Start
Dec.
Dec.
Inc.
Dec.
Inc.
Inc.

Aer check all the mode, to start the process press key for more than 2 seconds.
The screen displays the present state of process. To stop It press key;
Descripon: :the type of baery, :operang mode: CHG=charge、
DSC=discharge、DCHG>CHG or CHG>DCHG=the cycle mode; :elapsed me,
:charge/discharge current of the baery, :voltage of the baery pack,
:capacity of charge/discharge
Enter
Start
Mode
Esc
Mode
Esc
You can inquire the temperature and V connuaIIy by press Key
1 2
3
45
6
Dec./Inc.
This is programmed for charging Pb baery with nominal voltage from 2 to 24v, Pb baery can not be charged rapidly. They
can only deliver relavely lower current compare to their capacity. The opmal charge current will be 1/10 of the capacity.
Please always follow the instrucon supplied by the manufacturer of baery.
Pb baery program
charging Pb baery
Enter
Start

As you can see on le, you can set up the charge current on the le. The nominal of the
second line and voltage of the baery on the right of the second line. The charge current
ranges from 0.1-10.0A and the voltage should be matched with the baery being charged.
Start the charge process by pressing key for more than 2 seconds.
The screen displays the state of charging process. To stop charging forcibly, press key
once.
NiMH CHARGE Aut
CUR LINIT 5.0A
NiMH DISCHARGE
1.0A 11.5V NiMH 2.0A 7.42V CHG 022:45 00890
NiMH CYCLE
DCHG CHG 3
v
Pb CHARGE
4.0A 12.0V(6P)
Pb-6 4.0A 12.59V
CHG 022:43 00682
Mode/Esc
Enter
Start >2S
Enter
Start >2S
123456
Mode
Esc

discharging Pb baery
Set discharge current on the le and final voltage on the right, the discharge current ranges
from 0.1-5.0A and the voltage should be matched with baery being discharged. Start the
discharge process by pressing key for more than 2 seconds.
Enter
Start
The screen displays the current state of discharge.
save data and load data program
This charger can store /load up to 5 data of baeries, you can out the data for the process without seng up the
program again.
save data
Press key to the screen on the le, then press key to enter into the submenu.
The blinking (01) shows you the data No, you can press key to change it. Press
key can select the type of baery, voltage, capacity, and you can set them by pressing
key, then press key for more than 2 seconds to select the charge mode.
Mode
Esc
Mode
Esc
Enter
Start
Enter
Start
Enter
Start
Dec./Inc.
Dec./Inc.
Dec./Inc.
Seng up charge/discharge current and final voltage.
To save the data, press key for more than 2 seconds.
Enter
Start
Enter
Start
Enter
Start
load data
Press key to the screen on the
le, and then press key to enter
the submenu.
You can press key to
select the data number when
the (01) field is blinking.
Press key for more than 2
seconds, it will show you the le
screen, loading the data.

PROGRAM SELECT
LOAD DATA LOAD (01) NiMH 14.4V 3000mAh LOAD…
Pb DISCHARGE
4.0A 12.0V(6P)
Pb-6 0.4A 12.59V
DSC 022:43 00682
Enter
Start >2S
Enter
Start >2S
Enter
Start >2S
Enter
Start >2S
Mode
Esc
Mode
Esc
PROGRAM SELECT
SAVE DATA
SAVE (01) NiMH
14.4V 3000mAh
NiMH CHARGE AT*
CUR LIMIT 5.0A
SAVE…
Enter
Start
Enter
Start

Warning and error messages
The output is connected to a baery with incorrect polarity.
This will be displayed in case of detecng an interrupon of the connecon between baery
and output or voluntarily disconnecng the charge lead during the operaon of charge or
discharge on output.
There was a short-circuit at output. Please check the charging leads.
The voltage of input power drops below the limit.
The voltage of Lithium baery pack was selected incorrectly. Verify the voltage of baery
pack carefully.
There happens the malfuncon at the charger circuit by any reason.
The processor detects the voltage is lower than you set at Lithium program. Please check the
cell count of the baery pack.
The processor detects the voltage is higher than you set at Lithium program. Please check the
cell count of the baery pack.

REVERSE POLARITV
CONNECTION BREAK
SHORT ERR
INPUT VOL ERR
VOL SELECT ERR
BREAK DOWN
BATTERY CHECK
LOW VOLTAGE
BATTERY CHECK
HIGH VOLTAGE

The voltage of one of the cell in the Lithium baery pack is too high. Please check the voltage
of the cell one by one.
The voltage of one of the cell in the Lithium baery pack is too low. Please check the voltage
of the cell one by one.
There is bad connecon at the individual connector. Please check the connector and cables
carefully.
The internal temperature of the unit goes too high. Cool down the unit.
The processor can not connue to control the feeding current by any reason. The unit needs
to be repaired.

BATTERY VOL TAGE
CELL LOW VOL
BATTERY VOL TAGE
CELL HIGH VOL
BATTERY VOL ERR
CELL CONNECT
TEMP OVER ERR
CONTROL FAILURE
Although the charger is designed to work in a stable environment to play a role, but in use, you sll need careful
maintenance, as long as these important ps to follow, that is easy and effecve use of your charger.
When you start the process, especially the discharge process, the unit will become warm, please keep clear of the heat
area and do not cover it by anything when using.
Do not keep it in a environment below 5℃ or above 50℃
Use it carefully, do not use it in a wet or corrosive environment.
Keep all the inflammable volale materials well away from operang area.
Please don’t let the charger get hurt through falling, bumping, striking, shaking, and heavy press and so on.
Safety message

Do not aempt the voltage higher than the requirement by manufactures.
Ensure the type of the baery and the voltage of the baery pack are selected correctly. Do not use the different types
of different types or different capacies synchronously.
The standard accessories can only support one baery pack. When you are willing to use mul-packs, please separately
purchase the special accessories, never do a disassembly or alteraon to the charger.
Do not aempt to charge/discharge the non-recharged baery or damaged baery.
Keep the charger away from children and pet at all me! Never leave the charger unsupervised when it is connected to
its power supply.
After-sale service and guarantee
Thank you for purchasing this balance charger, iMaxRC will do its best to provide you with a comprehensive aer-sale
service and protect your rights and interests. Since you purchase the unit, you can enjoy the lifelong guarantee service.
We warrant this product for a period of one year from the date of purchase, if it has a quality problem itself, all guarantee
will be free; In case customers can not provide an effecve cerficate of purchase, we will refer the date of machine’s
internal.
If it is over one year since the purchase date, an appropriate cost will be charged, users need to bear the transportaon
cost back and forth.
User disassembly, alteraon, or damage caused by improper use, they should bear the maintenance and transport costs.
Aer-sale procedure:
When you can not use the product normally, please contact the local franchiser or the aer-sale service person. Aer
products have been confirmed damaged or unable to confirm the causes, you can send it to the company directly or
through the franchiser.
We will normally repair completed and send it to customers within five working days aer receive it.
All rights revised by iMaxRC to commit modificaons. www.imaxrc.com



Warning:
              
           
           
imaxRC Co.,LTD
•Add: F4 201-205, F518 IDEALAND Baoyuan Road,
Baoan,Shenzhen,P.R. C
•Tel: [phone]
•Fax: [phone]
•Web: www.imaxrc.com

All specifications and figures are subject to change without notice.
Printed in China ©2010
06 AC
b6