impact 070018151 User manual

7’ X 12’ STORAGE SHED – SHELTER
070018151 / 070018152
Parts:
(6) PCS A PIPE
(6) PCS H –FOOTPAD HARDWARE
(8) PCS I –SINGLE & DOUBLE BRACKET HARDWARE
(32) PCS J –BALL BUNGEES
(1) PCS L –COVER
(1) PCS M –ENDWALL
(16) PCS B PIPE
(6) PCS C - 3-WAY FITTING
(6) PCS D - 4-WAY FITTING
(6) PCS E - STEEL FOOTPAD
(8) PCS F –SINGLE BRACKETS
(4) PCS G –DOUBLE BRACKETS
Step 1: Organize Pipe and Fittings
Layout all pipe as per the pattern below. All 3-WAY “C” fittings should be placed at the four corners and at the two
peaks, 4-Way fittings “D” in the center along the center rib.
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C
D
D
D

Step 2: Assemble roof framework
a. Start with the front center peak 3-way fitting “C”, insert the “A”pipe into each end that is angled. This will
create the peak.
b. Next insert the “B” pipe into the horizontal end of the 3-way fitting. This starts the horizontal peak framework.
c. Holding the prebuilt section, have the second person insert the horizontal end of 4-way fitting “D” onto the
open end of the pipe”2”. Insert each pipe into open end of the 4 way fitting to create the angle. At this point
the pre-built frame work will support itself.
d. Repeat Steps until all the roof frame pipe assembled. There should be 3 sections.
Starting at the front of the unit, assemble the horizontal side framework to the prebuilt roof. Complete the assembly of
one side before working on the other.
e. Attach the 3-way corner fitting “C” to the “A” pipe that is pre-assembled.
-Note that the angled end of the fitting should be attached to the peak and the leg (leg pipe will be
assembled last)
f. Attach the “B” pipe to the horizontal end of the fitting that will run the length of the unit.
g. Repeat this process with all 4-way fittings
Step 3: Insert the legs and put on cover
a. Attach the foot pads “E” to one end six “B” pipe with the “H” hardware nut and bolt. These will be the legs.
b. Starting on one side: insert 3 of the “B” pipe into the last opening of each 3-way and 4-way fitting. Ensuring the
foot pad angles are all In the same direction and flush when standing.
c. Remove the cover from the bag and unfold placing it on the side of the unit with the pre-inserted legs. Locate
the bottom of the cover (front and back) and start to unfold pulling it over the frame centering the peak of the
cover to the peak of the frame.
d. Next insert the remaining 3 leg pipe “B”. Folding back the cover partially so you can grab ahold of the frame lift
and insert the last three leg pipe. From here you will be able to adjust and fit the cover properly.

Step 4: Insert support bar and fit cover
a. On the inside of the cover locate the pockets (6) total. Slide in one “B” pipe into each pocket. This is the last of
the “B” pipe. Adjust the cover slightly to make sure the support bars “B” pipe are even in height on each side of
the frame.
b. Starting on one side, working front to back, attach (2) of the “F” Single clamp brackets around the leg “B” pipe
and to the horizontal support bar “B” pipe using (1) of the “I” Nut and Bolt. Be sure that the nut is facing inside
the frame so that it cannot wear the cover. Do not completely tighten bolt yet.
c. Next attached the double clamp “G” around the center leg pipe “B” and two of the horizontal “B” support bars
using (2) of the “I” Nuts and Bolts. Repeat step B on the third leg and assemble the opposite side.
d. Once all six “B” support bars are connected using the single and double sided clamps push down on each side to
even the cover and aligning all the bars so that they are even and tighten the nuts.

Step 5: Attach from End Wall
a. Remove the end wall and unfold, locate the peak of the wall and align to the inside peak of the cover. Centering
the wall and lining up the velcro strips adhere the top left and top right peaks of the wall to the inside of the
cover, making sure there is a tight seal. Then work your way down the left and right length of the cover all the
way to the base of the unit.
b. Next roll up the front door to enter the unit to attach the velcro strips to the frame and loop the ball bungees
through the grommet holes and attach around the frame.
IMPORTANT: Once the legs and the cover is assembled, your canopy / carport can fly away in medium to heavy winds.
It is IMPERATIVE that your canopy / carport is an anchored down NOW. Anchoring system sold separately.

Anchoring Instructions
The canopy / carport is designed for temporary use. Once assembled the unit MUST be securely anchored to the ground
or a permanent structure to prevent damage from wind.
Medium to Severe winds will cause damage to the frame and it to twist, unanchored legs will fall and could cause
damage to the frame, cover, or surroundings causing the roof to collapse. If severe winds or weather is expected you
must remove the cover to prevent damage, otherwise the frame could fly away, or the cover to be ripped. A separate
anchoring system is recommended for purchase the included ground spikes and rope are NOT a secure method to
SOLELY anchor the frame.
Impact Canopy Auger Style Anchoring Kit: (sold separately)
Designed to work on medium to hard surfaces, Grass; Dirt; Gravel with hard subsurface. Not to be used on Sand, loose
gravel or concrete.
Step 1: Starting at one corner - Measure 36 inches / 96.44cm from each leg. Take one of the auger anchors and screw
into the ground. Leave about 2 inched between the eyebolt and the ground.
Step 2: Using the rope 10’ increments tie around the inside 3way corner fitting or the connector on the corner of the
cover.
Step 3: Pulling the rope tight, loop through the eyebolt of the grounded anchor and securely tie.
Repeat step on all legs of the unit one side at a time. If you have an 8 let unit –repeat 8 times.
Step 4: Finish to Screw down the grounded anchors so that is it completely flush with the ground. And equally taut on
both sides of the canopy. Be sure to continuously check that all anchors and rope is taut and secure to ensure the unit
stays properly anchored. Reminder in high winds remove cover.

WARRANTY:
Impact Canopy strives to bring products to the market that are superior free of defect. We are confident that you will be
completely satisfied with your canopy / carport. Listed below are precautions that should be taken to ensure proper
safety and use of your unit.
This structure is designed for temporary use and not recommended during extreme weather conditions or as a
permanent structure. Ensure that the frame is properly anchored and remove the cover during extreme weather
conditions. This structure is not designed for high winds or heavy snow fall.
-Keep all direct flame and heat sources away from fabric. The fabric is treated with fire retardant coating but
will burn / melt if left in continuous contact with any flame source.
Care Instructions: Use warm water, soap and a light brush or cloth to clean the fabric of this canopy / carport.
-Do NOT use Bleach, Dry Clean, or Machine Wash the cover or sidewall enclosure kit
-Do Not hang or suspend anything to the frame, cover, or grommets of the unit.
-Immediately remove and rain or snow accumulation on the cover. This can cause the cover to fault, rip, or
collapse the roof.
-Removing, water, snow or ice accumulation; by using a ladder and brush away from the top of the cover. Do
not stand under the unit and push the cover up to remove. This can be dangerous if the cover or frame
happen to collapse from the weight of the water, snow or ice.