TMG TMG-DT3063-PRO User manual

▶W W W . T M G I N D U S T R I A L . C O M P 0 / 22 T o l l F r e e : 1 - 877-761-2819

▶W W W . T M G I N D U S T R I A L . C O M P 1 / 2 2 T o l l F r e e : 1 - 877-761-2819
Main Specifications :
Assembly size : W9.15 x L19.2 x H6 (m) / 30 x 63 x 19.68 (ft)
Ridge height : 6m / 19.68 ft
Peak clearance : 5.4m / 17.7 ft
Front and back door : 4.27 x 3.96 (m) / 14 x 13 (ft)
Shoulder height : 3.6 m / 11.8 ft
Prior to assembly
Please read the instructions carefully before installation. It is very important to follow
your local safety regulations and industry standards during installation. Regulations may
include but are not limited to:
• Safety helmets, protective eyewear, and clothing
• Safety harnesses for all elevated workers
• Proper ladder, cage, and safety operation
Check all components and parts before installation. All parts are marked with a part
number, please refer to the parts list to ensure you have all parts.
Choose a day with low or no wind to install, it is hard to assemble with heavy wind. Do
not make any alterations to the structure. Do not hang any weight on the frame during
installation, including parts. We are not responsible for any damages or injuries caused by
inappropriate installation, unauthorized modifications or extreme weather.
This building is not intended for human occupancy.
It is recommended to use heavy duty duct tapes to tape the tube connection joint spots to
protect the cover from damage and worn. It will help to extend the cover life span.
Check the parts list below to make sure all parts are received prior to assembly.

▶W W W . T M G I N D U S T R I A L . C O M P 2 / 2 2 T o l l F r e e : 1 - 877-761-2819
Frame structure diagram.

▶W W W . T M G I N D U S T R I A L . C O M P 3 / 2 2 T o l l F r e e : 1 - 877-761-2819
TMG-DT3063-PRO Part List
Parts
Code
Graphical
Description
Length
Qty
Box
1
Peak arch tube
(for 7 middle trusses )
2570mm
7
B
1A
Peak arch tube
(for front and rear
truss)
2570mm
2
B
2
Upper rafter tube
(for middle trusses)
2921mm
14
A
2A
Upper rafter tube
(for front and rear
truss)
2921mm
4
A
3
Shoulder tube
(for middle trusses)
1757mm
14
B
3A
Shoulder tube
(front and rear
trusses)
1757mm
4
B
4
Sidewall tube
(middle trusses)
2878mm
14
A
4A
Sidewall tube
(front and rear left
truss)
2878mm
2
A
4B
Sidewall tube
(front and rear right
truss)
2878mm
2
A
5
Roof purlin
(horizontal tube)
2440mm
72
A
5L
Baseplate for front
and rear truss left
corners
W260xL520mm
2
B
5R
Baseplate for front
and rear truss right
corners
W260xL520mm
2
B
6L
Left baseplate of
front and rear door
frame
W150xL200mm
2
B

▶W W W . T M G I N D U S T R I A L . C O M P 4 / 2 2 T o l l F r e e : 1 - 877-761-2819
6R
Right baseplate of
front and rear door
frame
W150xL200mm
2
B
7
Baseplates for middle
truss
W260xL480mm
14
B
7A
Ratchets
(3T)
46
B
7B
Expansion bolts
φ16x150mm
88
B
8
Ceiling cross bar
(front and rear truss)
2083mm
2
B
9
Ceiling cross bar
(front and rear truss)
2233mm
2
B
9L
Front and rear
vertical door rail
(left side upper part)
1984mm
2
B
9R
Front and rear
vertical door rail
(right side upper part)
1984mm
2
B
9A
Side door left tube
2027mm
2
B
9B
Side door right tube
2027mm
2
B
9C
Side door
L2005xW925mm
2
B
10
Door center vertical
supporting rod for
cross beam
(front and rear truss)
1018mm
2
B
10L
Front and rear
vertical door rail (left
side lower part)
2625mm
2
B
10R
Front and rear
vertical door rail
(right side lower part)
2625mm
2
B
11
Door frame
horizontal tube
(front and rear truss)
1982mm
6
B
11C
Side door upper tube
1980mm
2
B

▶W W W . T M G I N D U S T R I A L . C O M P 5 / 2 2 T o l l F r e e : 1 - 877-761-2819
12
Bottom tension bar
(front and rear truss)
1970mm
2
B
12B
Bottom tension bar
815mm
2
B
13
Front and rear door
hand winch crossing
tube
1984mm
2
B
14
Top cover tension
tube
1993mm
20
A
15
Front and rear roll up
door dropping tubes
(to connect #16)
2195mm
14
A
16
Front and rear roll up
door dropping tubes
(to connect #15)
2192mm
14
B
17
Sidewall frame steel
tension cables
φ6x4050mm
20
B
18
Ridge steel tension
cables
(front and rear
trusses)
φ6x2800mm
24
B
19
Middle truss crossing
steel tension cables
φ6x3990mm
7
B
20
Front and rear truss
left and right steel
cables
φ6x3900mm
4
B
21
Tie down straps
(for #7A)
W38xL800mm
46
B
22
Cable connection
plate
91mm
34
B
22A
Pressing plate
2m
12
B
22B
Pressing plate
1m
2
B
23
Roll up door hand
winch
(1200 lb)
2
B
23A
Wire rope for front
and rear door hand
winch
φ4mm x 15m
2
B
23B
Right pulley system
for front and rear
doors
150mm
2
B

▶W W W . T M G I N D U S T R I A L . C O M P 6 / 2 2 T o l l F r e e : 1 - 877-761-2819
23C
Left pulley system for
front and rear doors
150mm
2
B
24
Front and rear
vertical door rail
connection plate
240mm
4
B
24A
Front and rear
vertical door rail end
plate (floatable to
keep door rail
straight)
220mm
4
B
25
Tension tube end
water plug
(φ32)
12
B
26
Tube clamps
(φ48)
6
B
27
Tapping screw
#12x25mm
120
B
28
Self locking bolt
and nuts
M10x70mm
81
B
29
Strengthened bolt
and nuts
M12x30mm
288
B
30
Hex bolt and nuts
M10x50mm
14
B
31
Hex bolt and nuts
M10x70mm
68
B
32
Braided rope
160m
1
B
33
Roof fabric tarp cover
W18.4xL19.8m
1
B
34
Front and rear truss
cover panel
W6.2xL9.1m
2
B
35
Front and rear roll
up door cover panel
W4.2xL4.6m
2
B
36
Front and rear fabric
tarp secure pin
200mm
2
B
37
Plastic hose
(in grooves at both
ends of #33)
φ25mmxL4m
10
B
37A
Connector
(for connection #37)
φ25mm
8
B
38
Scratch resistant tape
10m
4
B

▶W W W . T M G I N D U S T R I A L . C O M P 7 / 2 2 T o l l F r e e : 1 - 877-761-2819
Step 1 : Baseplate positioning and installation.
Installation diagram of expansion bolt.
No.
Part
Qty
No.
Part
Qty
5L
2
6R
2
5R
2
7
14
6L
2
7B
80

▶W W W . T M G I N D U S T R I A L . C O M P 8 / 2 2 T o l l F r e e : 1 - 877-761-2819
Step 2 : Assemble all trusses.
 Front and rear trusses.
No.
Part
Qty
No.
Part
Qty
1A
1x2
4A
1x2
2A
2x2
4B
1x2
3A
2x2
29
24x2

▶W W W . T M G I N D U S T R I A L . C O M P 9 / 2 2 T o l l F r e e : 1 - 877-761-2819
 Middle trusses. (7 trusses)
No.
Part
Qty
No.
Part
Qty
1
1x7
4
2x7
2
2x7
29
24x7
3
2x7

▶W W W . T M G IN D U S T R I A L .C O M P 10/ 2 2 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
 Lay down all (9) trusses on the ground when the assembly is all completed and
before moving to next step, and then wrap (#38) around the sharp points of
the joint to avoid friction between the fabric and the interface, resulting in
fabric damage.
No.
Part
Qty
38
4

▶W W W . T M G IN D U S T R I A L .C O M P 11/ 2 2 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
Step 3 : Put up the front truss. (It is suggested to use crane for hoisting)
No.
Part
Qty
29
8

▶W W W . T M G IN D U S T R I A L .C O M P 12/ 2 2 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
Step 4 : Put up the rest trusses.
 Refer to step 3 to put up the rest trusses, connect all purlins (#5) with bolt (#28)
and secure all bolts firmly on each span before going to next truss .
No.
Part
Qty
No.
Part
Qty
5
9
29
8
28
18

▶W W W . T M G IN D U S T R I A L .C O M P 13/ 2 2 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
 Repeat above step to put up all other trusses (from 3rd to 9th truss), and
connect all purlins.
No.
Part
Qty
No.
Part
Qty
5
63
29
56
28
63

▶W W W . T M G IN D U S T R I A L .C O M P 14/ 2 2 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
 Tension cable installation . All cables are diagonally installed on each side of
the interval.
No.
Part
Qty
No.
Part
Qty
17
20
19
7
18
24
22
34

▶W W W . T M G IN D U S T R I A L .C O M P 15/ 2 2 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
Step 5 : Front and rear trusses to complete. (2 trusses)
No.
Part
Qty
No.
Part
Qty
7B
4x2
12
1x2
8
1x2
12B
1x2
9
1x2
13
1x2
9A
1x2
20
2x2
9B
1x2
23B
1x2
9C
1x2
23C
1x2
9L
1x2
24
2x2
9R
1x2
24A
2x2
10L
1x2
25
4x2
10R
1x2
26
3x2

▶W W W . T M G IN D U S T R I A L .C O M P 16/ 2 2 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
10
1x2
30
7x2
11
3x2
31
32x2
11C
1x2
27
8x2
Step 6: Install front and rear cover panels
 Lift up (#34) cover panel, starting from the center point of the frame (highest
ridge point) use ropes (#32) through the grommets to tie the panel to the truss
firmly. All grommets need to be tied to the frame as shown.
No.
Part
Qty
No.
Part
Qty
32
1
34
1x2

▶W W W . T M G IN D U S T R I A L .C O M P 17/ 2 2 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
Install the front and rear door pressing plate. Trim the side door tarp.
No.
Part
Qty
22A
6x2
22B
1x2
27
52x2

▶W W W . T M G IN D U S T R I A L .C O M P 18/ 2 2 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
Step 7 : Install mechanical roll up doors.
 Door curtain installation.
No.
Part
Qty
No.
Part
Qty
15
7x2
35
1x2
16
7x2

▶W W W . T M G IN D U S T R I A L .C O M P 19/ 2 2 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
 Front and rear door installation, please look at the door from inside.
 The hand winch (#23) comes with a shorter cable, we call it cable (#B).
No.
Part
Qty
No.
Part
Qty
23
1x2
32
1
23A
1x2
36
1x2
31
2x2