Shelters4Less SR1588 User manual

Assembly Instructions
Shelter type: SR1588
SR1588-01-15022017-UK
Email : [email protected]
Web : www.shelters4less.co.uk
Tel : [phone]

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
Tools required:
Drill/Screwdriver
Mallet
Hack saw
17 mm Spanners
T5 Torx bit
Exploded View

3
PARTS LIST
Fittings M10 X 60mm
Nut Washer
Black
Bolt Cap
T25 AB1210
25mm Tech screw
M10 x 100mm Concrete
Bolt
Qty.
45 45 90 90 80 8
Image
ITEM NO.
PART NO.
DESCRIPTION
DIMENSION IMAGE
QTY.
1
S1
Frame
2000 x 1035
6
2
CB1
Bracket
110 x 110 x 40
6
3
JF1
Bracket
220 x 40
8
4
ST1
Stub
145 x 40 x 40
2
5
JF2
Bracket
130 x 30 x 3
4
6
RB2
Bracket
110 x 46
10
7
R5
Rafter
2159 x 40 x 40
1
8
L1
Bracket
95 x 45 x3
8
9
R4
Rafetr
2159 x 40 x 40
4
10
ST4
Tie bar
2080x40x40
2
11
JF3
Bracket
210 x 30 x 5
1
12
P4
Post
2000 1
13
SS
Sealing strip
Trim to 2220
20
14
ACE2
Roof Sheet
2210 x 1050
2
15
ACC2
Roof Sheet
2210 x 1030
2
16
RC2
Roof strip
2180 5
17
A2
Roof Angle
2080 2
18
FT1
Foot Bracket
109 x 100 x 3
8
19
EC40
Plastic End Caps
40 x40
14

4180
1075
1035
JF1
JF1
CB1
Check the dimension
of the shelter to
ensure correct alignment
S1
S1
CB1
CB1
JF1JF1
S1
S1S1S1S1
ENSURE CORRECT
ALIGNMENT ON
BOTH SIDES
JF1
S1
TOP VIEW
Step 1
Assemble S1 frames to make up the main structure using CB1 brackets
in the corners and JF1 brackets on the straight joints.
4

JF2JF2
JF2
RB2
R5
RB2
R4
JF2
L1
L1
ST1 Stub
Detailed view
ST1
JF2
CB1
JF1
R5
R4
Identifying Rafters:
Step 2
Attach the ST1 Stub as shown below. Then attach the R4 and R5 rafters
using RB2 brackets on the back of the shelter and ST1 stubs in the middle.
Bolt one L1 bracket to each rafter.
5

ST4
ST4
L1
L1
L1
JF3
RB2
RB2
P4
ST4
ST4
P4
Step 3
Assemble the T-frame using two ST4 tie bars and a P4 post. Join the two
ST4 tie bars together first, using a JF3 bracket and two L1 brackets on the
other side. Then attach the P4 post using two RB2 brackets.
Bolt on four aditional L1 brackets to the holes in the center of the ST4 bar.
6

R4
R4
L1
RB2
RB2
FT1
FT1
FT1
FT1
FT1
FT1
FT1
L1
L1
RB2
R4
RB2
RB2
FT1
L1
L1
L1
Step 4
Use the L1 brackets to attach the T-bar to the front of the shelter and install
the R4 rafters using RB2 brackets on the rear and L1 brackets at the front.
Attach the FT1 brackets and move the shelter in to its final position.
Make sure everything is square before using anchor bolts to secure
it to the ground.
7

SS
SS
SS
SS
SS
SS
ACE2
ACE2
ACC2
ACC2
Step 5
Stick two sealing strips (SS) to each rafter and align the ACE2 panels to
the outside of the end rafters then centralise the ACC2 panels with even gaps.
8

RC2
RC2
RC2
RC2
SS
SS
SS
SS
SS
A3
A3
X
A3
A3
RC2
RC2
DETAIL X
SEALING STRIPS AND FIXING DETAIL
(SCALE 1 : 1)
Step 6
Use Tech screws to screw down the RC2 strips to secure the roof panels
and attach the A3 angle using the same screws.
Then fit the Black plastic caps on exposed nuts and bolts. Fit the square
end caps to any open ends of box sections.
9

Notes:
10