Impex MARCY IVT-845 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
IVT-845
Retain This
Manual for
Reference
10-30-08
OWNER'S
MANUAL
MARCY
INVERSION CHAIR
IVT-845
IMPEX®INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN....................................................................................……….. 1
IMPORTANT SAFETY NOTICE...................................................................……….. 2
HARDWARE PACK……….....….....................................................................……….. 4
ASSEMBLY INSTRUCTIONS.........................................................................……….. 5
EXPLODED DIAGRAM………………………………………………………………………14
PARTS LIST………….………….......................................................................………. 15
WARRANTY.................................................................................................…………. 16
ORDERING PARTS.......................................................................................…………16
BEFORE YOU BEGIN
Thank you for selecting the Marcy Inversion Chair IVT-845 by IMPEX®
FITNESS PRODUCTS. For your safety and benefit, read this manual
carefully before using the machine. As a manufacturer, we are committed
to provide you complete customer satisfaction. If you have any questions,
or find there are missing or damaged parts, we guarantee you complete
satisfaction through direct assistance from our factory. To avoid
unnecessary delays, please call our TOLL-FREE customer service
number. Our Customer Service Agents will provide immediate assistance
to you.
Toll-Free Customer Service Number
1-800-999-8899
Mon. – Fri. 9 a.m. – 5 p.m. PST
www.impex-fitness.com
[email protected]m
1

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands and feet away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. MUST fasten the Seat Belt before doing Inversion exercise.
13. Make sure both feet are securely lock by the Inversion Foot Locker.
14. Both hands need to hold on the handles on the Support when doing Inversion
exercises.
15. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect Seat Belt, Knuckle, Strap, and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

WARNING LABEL REPLACEMENT
The warning label shown here has been placed on the Base Frame. If the label is missing or
illegible, please call customer service at 1-800-888-8899 for replacements. Apply the label in the location
shown.
3

HARDWARE PACK
#3 M8 x 2 ½” Allen Bolt (Qty 2) #4 Ø 5/8” Washer (Qty 16)
#5 M8 Aircraft Nut (Qty 5) #6 Ø ¾” Washer (Qty 5)
#7 M10 Aircraft Nut (Qty 5) #10 M8 x 5/8” Allen Bolt (Qty 16)
#11 Ø 5/8” Curved Washer (Qty 8) #13 M10 x 4” Allen Bolt (Qty 2)
#14 M10 x 4 5/8” Allen Bolt (Qty 2) #15 Nut Cap (Qty 4)
#17 M8 x 2 3/8” Allen Bolt (Qty 2) #25 M8 x 1 5/8” Allen Bolt (Qty 1)
#27 Foam Roll End Cap (Qty 4) #29 ¾” Rubber Bumper (Qty 1)
#30 1 5/8” Rubber Bumper (Qty 1) #31 M6 x 2 ½” Philips Screw (Qty 1)
Crossing Wrench (Qty 1) Allen Wrench (Qty 1)
4

ASSEMBLY INSTRUCTION
Tools Required for Assembling the Machine: Two Adjustable Wrenches, two Allen
Wrenches, and one Philips Screwdriver. NOTE: It is strongly recommended that
this machine to be assembled by two or more people to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Place the Base Frame (#1) on flat floor. If the floor is not flat, twist the four Floor
Stabilizers (#69) under the frame to level the Inversion Chair.
B.) Attach the Front Vertical Frame (#2) to the Base Frame. Secure it with two M8 x 2 ½”
Allen Bolts (#3), two Ø 5/8” Washers (#4), and two M8 Aircraft Nuts (#5) from side, and
one Ø ¾” Washer (#6) and one M10 Aircraft Nut (#7) from bottom.
DAIGRAM 1
5

STEP 2 (See Diagram 2)
A.) Two people to assemble this step are highly recommended. Do not tighten
the Bolts until instructed to do so.
B.) Attach the pivots on the Rear Left & Right Support Tube (#40) & (#41) to the back
holes on the Left & Right Support (#8) & (#9). Secure each pivot to each Support
with one M10 x 4 5/8” Allen Bolt (#14), one Ø ¾” Washer (#6), and one M10
Aircraft Nut (#7).
C.)Attach the pivots one Front Left & Right Support Tube (#44) & (#45) to the front
holes on the Left & Right Support. Secure each pivot to each Support with one
M10 x 4” Allen Bolt (#13), one Ø ¾” Washer (#6), and one M10 Aircraft Nut (#7).
DIAGRAM 2
6

STEP 3 (See Diagram 3)
A.) Two people to assemble this step are highly recommended. Do not tighten Nuts and
Bolts until instructed to do so.
B.) Attach the Left & Right Support (#8) & (#9) onto the open bracket one the Base Frame (#1).
Make sure the Front Support Base (#47) is placed in front of the Front Vertical Frame
(#2).
C.) Secure each Support to the bracket with two M8 x 5/8” Allen Bolts (#10), two Ø 5/8” Washers
(#4) from the side, four M8 x 5/8” Allen Bolts (#10), four Ø 5/8” Curved Washers (#11) from
front and rear.
D.)Attach the Inversion Retaining Strap (#18) to the opening on the Front Vertical Frame (#2).
Align the holes. Secure the Inversion Retaining Strap to the Front Vertical Frame with one M8
x 2 3/8” Allen Bolt (#17), two Ø 5/8” Washers (#4), and one M8 Aircraft Nut (#5).
E.) Securely tighten all Nuts and Bolts installed in Step-2 and Step-3.
F.) Cover the four M10 Aircraft Nuts (#7) with four Nut Caps (#15).
G.)Make sure the pivots can move smoothly. DIAGRAM 3
7

STEP 4 (See Diagram 4)
A.) Attach the 1 5/8” Rubber Bumper (#29) to the Foot Support (#19). Attach the ¾” Rubber
Bumper (#30) to the 1 5/8” Rubber Bumper (#29).
B.) Secure them together to the Foot Support with one M6 x 2 ½” Philips Screw (#31).
DIAGRAM 4
8
STEP 5 (See Diagram 5)

A.) Pull the Foot Support Lock Knob (#20) and then insert the Foot Support (#19) into the Foot
Support Base (#47) from bottom. Release the Lock Knob and lock the Foot Support at
desired position.
DIAGRAM 5
9