Impex MARCY SM-4008 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
SM-4008
Retain This
Manual for
Reference
100806
OWNER'S
MANUAL
MARCY®
SMITH MACHINE
SM-4008
IMPEX®INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN..................................................................……………. 1
IMPORTANT SAFETY NOTICES.................................................................… 2
SMITH MACHINE HARDWARE PACK….......…............................................. 4
SMITH MACHINE ASSEMBLY INSTRUCTIONS............................................ 6
EXPLODED DIAGRAM……………………………………………………………. 21
SMITH MACHINE PARTS LIST………..………………………………………… 22
MULTI-PURPOSE BENCH HARDWARE PACK……………………………….. 23
MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTIONS............................ 24
EXPLODED DIAGRAM…………………………………………………………… 29
MULTI-PURPOSE BENCH PARTS LIST………………………………………… 30
WEIGHT RESISTANCE CHART…………………………………………………… 31
WARRANTY.................................................................................................… 32
ORDERING PARTS.....................................................................................…
32
BEFORE YOU BEGIN
Thank you for selecting the MARCY®SM-4008 by IMPEX®INC. For your safety
and benefit, read this manual carefully before using the machine. As a
manufacturer, we are committed to provide you complete customer satisfaction.
If you have any questions, or find there are missing or damaged parts, we
guarantee you complete satisfaction through direct assistance from our factory.
To avoid unnecessary delays, please call our TOLL-FREE customer service
number. Our Customer Service Agents will provide immediate assistance to
you.
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]
1

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual before
you assemble or operate your machine. In particular, note the following safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
5. Maximum weights on the Weight Bar: 300 lbs.
6. Maximum weights on Leg Developer: 100 lbs.
7. Maximum weights on Cross-over, Lat Pull: 200 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

WARNING LABEL PLACEMENT
The warning labels shown here have been placed on the Rear Base, and Bench Rear Stabilizer. If the
labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply
the labels in the location shown.
3

SMITH MACHINE HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
4

SMITH MACHINE HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
5

SMITH MACHINE HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
6

SMITH MACHINE HARDWARE PACK
7

SMITH MACHINE ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches.
NOTE: It is strongly recommended that two or more people assemble this machine to
avoid possible injury.
STEP 1 (See Diagram 1)
A.) Do not tighten Nuts and Bolts until instructed to do so.
B.) Insert a Base Frame (#5) into the Rear Left Vertical Frame (#3). Secure it with two M10 x
¾” Allen Bolts (#90) and two Ø ¾” Washers (#107).
C.) Repeat B to install the other Base Frame to Rear Right Vertical Frame (#4).
D.) Attach Rear Base Frame (#8) to Rear Left and Right Vertical Frame. Secure each end
with two M10 x 2 ½” Allen Bolts (#95), four Ø ¾” Washers (#107), and two M10 Aircraft
Nuts (#110).
E.) Repeat D to connect Rear Top Beam (#6) to Rear Left and Right Vertical Frame.
DIAGRAM 1
8

STEP 2 (See Diagram 2)
A.) Do not tighten the Nuts and Bolts until instructed to do so.
B.) Insert a Guide Rod (#24) into the hole on left Base Frame (#5). Secure it with one M8 x 2
3/8” Allen Bolt (#103), two Ø 5/8” Washers (#106), and one M8 Aircraft Nut (#109). Slide
the Left Lower Safety Stop Frame (#26) onto the Guide Rod, and then slide one Safety
Stop Frame (#25) onto the Guide Rod.
C.)Attach the Front Left Vertical Frame (#1) onto the left Base Frame. Secure it with two M10
x 3 1/8” Allen Bolt (#98), four Ø ¾” Washers (#107), and two M10 Aircraft Nuts (#110).
D.)Attach one Upper Side Frame (#7) to the Guide Rod, Front Left Vertical Frame, and Rear
Left Vertical Frame (#3).
E.) Secure the Upper Side Frame to Rear Left Vertical Frame from side with one M10 x 2 ½”
Carriage Bolt (#88), one Ø ¾” Washer (#107), and one M10 Aircraft Nut (#110). Secure it
from rear with one M10 x 5/8” Allen Bolt (#87) and one Ø ¾” Washer (#107).
F.) Secure the Upper Side Frame to the Guide Rod with one M10 x ¾” Allen Bolt (#90), and
one Ø ¾” Washer (#107).
G.)Secure the Upper Side Frame to the Front Left Vertical Frame with one Left Chin-up
Bracket (#49), two M10 x ¾” Allen Bolts (#90) and two Ø ¾” Washers (#107).
H.)Repeat B to G above to install the other side.
I.) Attach the Chin-up Bar (#30) to the Left and Right Chin-up Bracket (#49 & #50). Secure
each end of Chin-up Bar with two M10 x 1 5/8” Carriage Bolts (#86), two Ø ¾” Washers
(#107), and two M10 Aircraft Nuts (#110).
9