Impex GD-600 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
GD-600
Retain This
Manual for
Reference
11-24-09
OWNER'S
MANUAL
ROCKING HAMMOCK
GD-600
IMPEX®INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICES..................................................................... 2
HARDWARE IDENTIFIER……......…............................................................... 3
ASSEMBLY INSTRUCTIONS........................................................................... 5
OPERATION………………………………………………………………………… 11
EXPLODED DIAGRAM.........................................................................………. 12
PARTS LIST...................................................................................................... 13
WARRANTY.................................................................................................…. 14
ORDERING PARTS.....................................................................................…. 14
BEFORE YOU BEGIN
Thank you for selecting the Rocking Hammock GD-600 by IMPEX®. For
your safety and benefit, read this manual carefully before using the
Hammock. As a manufacturer, we are committed to provide you complete
customer satisfaction. If you have any questions, or find there are missing or
damaged parts, we guarantee you complete satisfaction through direct
assistance from our factory. DO NOT RETURN THE UNIT TO THE STORE!
To avoid unnecessary delays, please call our TOLL-FREE customer service
number. Our Customer Service Agents will provide immediate assistance to
you.
Toll-Free Customer Service Number
1-800-999-8899
Mon. – Fri. 9 a.m. – 5 p.m. PST
www.impex-fitness.com
[email protected]
1

IMPORTANT SAFETY NOTICE
Please read the entire manual before assembling or operating the equipment. In
particular, note the following safety precautions to reduce the likelihood of injury.
1. Children must be supervised at all times and never left unattended with the unit.
2. Make sure the surfaces are free of objects that may cause tipping over.
3. Place the equipment on level ground, not less than 6 ft (1.8 m) from any structure or
obstruction such as fence, garage, house, overhanging branches, laundry lines, or
electrical wires.
4. Make sure bystanders are at least 5 feet away from the equipment while it is in motion.
No one should be allowed to walk close to, in front of, behind, or between moving
items.
5. Do not stand on the Rocking Hammock. This could cause the bed to tip over and result
in injury.
6. The Rocking Hammock is not designed to use by children.
7. Maximum user weight is 300 lbs.
8. Only one person should be using the Rocking Hammock at a time.
Care and Maintenance
1. Periodically inspect all parts. Check all bolts twice monthly during the usage season for
tightness and tighten as required. It is particularly important that this procedure be
followed at the beginning of each season.
2. Replace any worn and damaged part immediately. Check all coverings for bolts and
sharp edges twice monthly during usage season to be certain they are in place.
Replace when necessary. It is especially important to do this at the beginning of each
new season.
3. Use mild household spray cleaners and/or a damp rag to wipe clean. Do not use harsh
cleaning chemicals.
4. Sand rusted areas on tubular members and repaint using a non-lead based paint
meeting the requirements of Title 16 CFR Part 1303.
5. Disposal Instructions – The equipment can be safely disassembled and disposed
without unreasonable hazards. Call your local recycle agency regarding details of
recycling.
6. Inspect before and periodically during use for frayed ropes and torn seam. Call the
customer service department if any defects were found.
7. Inspect before and periodically during use for excessive rust, integrity of the welds, and
twist in hanging hardware. Call the customer service department if any defects were
found.
SAVE THESE INSTRUCTIONS. 2

WARNING LABEL PLACEMENT
The Warning Label shown here has been placed on the Stabilizer Frame. If the label is missing or illegible,
please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
3

HARDWARE IDENTIFIER
Part# Description Identifier
#2 Cap Washer (Qty 16)
#3 Cover Cap (Qty 16)
#24 M8 x 5/8” Allen Bolt (Qty 16)
Tools:
#5 Allen Wrench (Qty 1)
4

ASSEMBLY INSTRUCTION
Tool Required for Assembling the Machine: #5 Allen Wrench
NOTE: It is strongly recommended that two or more people assemble this machine to avoid
possible injury.
STEP 1 (See Diagram 1)
A.) Do not tighten Bolts until instructed to do so.
B.) Attach the two Stabilizer Tubes (#11) to the two Hammock Base Frames (#4).
C.)Secure each end of the Stabilizer Tube to the Hammock Base Frame with two M8 x 5/8” Allen
Bolt (#24) and two Cap Washers (#2).
D.)NOTE: The outer lip of the Cap Washer needs to face away from frame so the head of the
Bolt could be in the recess of the Washer. The groove inside the Cap Cover shold clip onto
the lip of the Cap Washer.
DIAGRAM 1
5

Step 2 (See Diagram 2)
A.) Do not tighten Bolts until instructed to do so.
B.) Insert a Hammock Body Support Tube (#12) through the sleeve next to the pillow on
Hammock Body (#15). NOTE: The pillow needs to be on top of the Hammock Body.
C.) Insert the Right Long Support (#6) into the right opening on the Hammock Base Frame (#4).
D.) Attach right end of the Hammock Body Support Tube to the Right Long Support Frame.
Attach the left end to the Left Long Support (#5).
E.) Insert the Left Long Support into the left opening on the Hammock Base Frame.
F.) Secure the Left and Right Support to the Hammock Base Frame with two M8 x 5/8” Allen
Bolts (#24) and two Cap Washer (#2) on each side.
DIAGRAM 2
6

Step 3 (See Diagram 3)
A.) Insert the Right Short Support (#8) into right opening on the Hammock Base Frame (#4).
B.) Insert the Hammock Body Support Tube (#12) through the other open sleeve on the
Hammock Body.
C.)Attach the right end of the Hammock Body Support Tube to the Right Short Support.
Attach the other end to the Left Short Support (#7).
D.)Insert the Left Short Support into the left opening on the Hammock Base Frame.
E.) Securely tighten all Bolts in previous step and this step.
DIAGRAM 3
7

Step 4 (See Diagram 4)
A.) Insert the Support Rod (#21) and Sun Shade Rod (#20) through the sleeve on the Sun
Shade (#14).
B.) Insert each end of the Support Rod into the Left and Right Rod Holder (#18) on Sun Shade
Support Frame.
DIAGRAM 4
8

Step 5 (See Diagram 5)
A.) Insert the Sun Shade Support Frame (#13) into the Long Support Cover Caps (#17).
DIAGRAM 5
9