Impex MARCY MWB-855 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MWB 855
Retain This
Manual for
Reference
07-25-03
OWNER'S
MANUAL
MARCY OLYMPIC BENCH
MWB-855
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: [phone] Fax: [phone]
www.impex-fitness.com
[email protected]

TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICE....................................................................... 2
HARDWARE PACK……….....…....................................................................... 3
ASSEMBLY INSTRUCTIONS........................................................................... 4
EXPLODED DIAGRAM.........................................................................………. 8
PARTS LIST…………………………………………………………………………. 9
WARRANTY.................................................................................................… 10
ORDERING PARTS......................................................................................... 10
BEFORE YOU BEGIN
Thank you for selecting the MARCY Olympic Bench MWB-855 by IMPEX
FITNESS PRODUCTS. For your safety and benefit, read this manual
carefully before using the machine. As a manufacturer, we are committed to
provide you complete customer satisfaction. If you have any questions, or
find there are missing or damaged parts, we guarantee you complete
satisfaction through direct assistance from our factory. To avoid unnecessary
delays, please call our TOLL-FREE customer service number. Our Customer
Service Agents will provide immediate assistance to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
[email protected]m

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

HARDWARE PACK
3

ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended two or more people assembling this
machine to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Connect the two Upright Beams (#1) by a Cross Brace (#2) in the mid-span. Align the
holes and secure each end of the Cross Brace with two M10 x 3 1/8” Carriage Bolts
(#44), one 4 ¾” x 2” Bracket (#21), two ∅¾” Washers (#52), and two M10 Aircraft
Nuts (#51).
B.) Insert two Crutches (#10) into the top openings on the Upright Beams. Secure them
with two Lock Knobs (#38) through selected holes to obtain desired height of the
Supports.
C.) Place the Backrest Adjustment Bar (#8) onto the selected slot on Upright Beams to
hold the desired incline.
D.) Insert one Weight Post (#11) to each Upright Beam. Secure it with one M10 x 1” Allen
Bolt (#46) and ∅¾” Washer (#52). Attach one Olympic Sleeve (#36) to each Post.
Secure the Sleeve to the post with one M8 x ½” Allen Screw (#55). Attach a Spring
Clip (#25) to each Sleeve. DIAGRAM 1
4

STEP 2 (See Diagram 2)
A.) Attach the Leg Developer Holder (#5) to the Front Stabilizer (#4). Secure it with three
M10 x 5/8” Allen Bolts (#47) and ∅¾” Washers (#52).
B.) Attach the Main Seat Support (#3) to the Leg Developer Holder (#5). Secure it with
three M10 x 2 ¾” Carriage Bolts (#45), M10 Aircraft Nuts (#51) and ∅¾” Washers
(#52).
C.)Attach the Main Seat Support (#3) to the Cross Brace (#2). Secure it with two M10 x 2
¾” Carriage Bolts (#45), one 4 ¾” x 2” Bracket (#21), two ∅¾” Washers (#52), and two
M10 Aircraft Nuts (#51). DIAGRAM 2
5

STEP 3 (See Diagram 3)
A.) Attach the Seat Bracket (#13) to the pivot on the Main Seat Support (#3). Push two
Bushings (#22) through the holes on the Seat Bracket into both ends of the pivot.
B.) Attach Backrest Incline Support (#7) in between the two Backrest Supports (#6) and
insert both ends into the side-holes on the Backrest Supports. Attach the Backrest
Supports to the Bushings. Secure it with one M10 x 7 ¼” Allen Bolt (#43), two ∅¾”
Washers (#52), and one M10 Aircraft Nut (#51).
C.) Place the other end of Backrest Support rest against the Backrest Adjustment Bar.
D.) When using the Squat exercise, lift up the Backrest Board to a near vertical position
and secure the Backrest Incline Support with a 4” L-shaped Pin (#23) into the open
slot on the Main Seat Support. Please note the only purpose of the Backrest Incline
Support and Pin is to get the Backrest Board out of the way while doing squat exercise
from the rear of the machine. They are not designed to support any weight or perform
any exercise.
E.) Place the Backrest Board (#17) onto Backrest Supports (#6). Secure it with four M6 x 1
3/8” Hex Bolts (#49) and Ø ½” Washers (#54).
F.) Attach the Seat Incline Adjustment (#20) to the Seat Bracket from bottom. Place the
Seat (#18) onto the Seat Bracket (#13). Secure the Seat with four M6 x 5/8” Hex Bolts
(#50) and ∅½” Washers (#54). Insert a 4” L-shaped Pin (#23) into selected hole on
Seat Incline Adjustment to obtain the desired height of Seat Pad.
G.) Attach the Arm Curl Pad (#19) to the Arm Curl Stand (#9). Secure it with two M8 x 5/8”
Allen Bolts (#48) and Ø 5/8” Washers (#53). Insert the Arm Curl Stand into the top
opening on the Leg Developer Holder. Secure it with a Lock Knob (#38).
6

STEP 4 (See Diagram 4)
A.) Attach the Leg Developer (#14) to the Leg Developer Holder (#5). Secure it with an
Axle (#39), two M10 x 5/8” Allen Bolts (#47), and two Ø ¾” Washers (#52).
B.) Insert one Foam Tube (#12) halfway through the hole on the Leg Developer Holder.
Insert two Foam Tubes halfway through the holes on the Leg Developer.
C.)Push six Foam Rolls (#37) onto the Tubes from both ends. Plug six Foam Roll End
Caps (#32) into the ends.
D.)Attach the Curl Bar Handle Support (#15) to the bracket on the Leg Developer and
secure it with a 3” L-shaped Pin (#24). When using the Leg Developer, remove the
Pin, Curl Bar, and the Arm Curl Stand.
E.) Attach an Olympic Sleeve (#36) onto the weight post on the Leg Developer. Secure it
with a M8 x ½” Allen Screw (#55). Attach a Spring Clip (#25) to the Sleeve.
DIAGRAM 4
7

8

PARTS LIST
KEY NO. DESCRIPTION Q’ty
1 Upright Beam 2
2 Cross Brace 1
3 Main Seat Support 1
4 Front Stabilizer 1
5 Leg Developer Holder 1
6 Backrest Support 2
7 Backrest Incline Support 1
8 Backrest Adjustment Bar 1
9 Arm Curl Stand 1
10 Crutch 2
11 Weight Post 2
12 Foam Tube 3
13 Seat Bracket 1
14 Leg Developer 1
15 Curl Bar Handle Support 1
16 Curl Bar Handle 1
17 Backrest Board 1
18 Seat 1
19 Arm Curl Pad 1
20 Seat Incline Adjustment 1
21 4 ¾” x 2” Bracket 3
22 Bushing 2
23 4” L-shaped Pin 2
24 3” L-shaped pin 1
25 Spring Clip 3
26 2 3/8” x 2” Crutch Sleeve 2
27 2” x 1 ¾” Sleeve 1
28 2 3/8” Square End Cap 4
29 2” Square End Cap 2
30 1 5/8” x 2 3/8” End Cap 2
31 ∅1” Cone-shaped End Cap 2
32 Foam Roll End Cap 6
33 ∅1” End Cap 1
34 1” Square End Cap 3
35 ∅1 1/8” x 1” End Cap 2
36 Olympic Sleeve 3
37 Foam Roll 6
38 Lock Knob 3
39 Axle 1
40 ∅2 3/8” Axle Bushing 2
41 ∅1 3/8” Spacer 2
42 Curl Bar Handle Grip 2
43 M10 x 7 ¼” Allen Bolt 1
44 M10 x 3 1/8” Carriage Bolt 4
45 M10 x 2 ¾” Carriage Bolt 5
46 M10 x 1” Allen Bolt 2
47 M10 x 5/8” Allen Bolt 5
48 M8 x 5/8” Allen Bolt 2
49 M6 x 1 3/8” Hex Bolt 4
50 M6 x 5/8” Hex Bolt 4
51 M10 Aircraft Nut 10
52 ∅¾” Washer 18
53 ∅5/8” Washer 2
54 ∅½” Washer 8
55 M8 x ½” Allen Screw 3
9