In The Ditch X Series User manual

TM FOR MORE INFORMATION: www.intheditch.com | [phone] | [email protected]
FAILURE TO FOLLOW THE SAFETY GUIDELINES LISTED MAY RESULT IN VOIDING ANY APPLICABLE WARRANTY, SERIOUS BODILY INJURY, OR DEATH.
!
IT IS VERY IMPORTANT THAT YOU PROPERLY FILL OUT YOUR PRODUCT REGISTRATION FORM AT REGISTRATION.INTHEDITCH.COM TO REGISTER YOUR EQUIPMENT.
BY SUBMITTING THE INFORMATION WITHIN 15 DAYS OF YOUR PURCHASE, YOUR WARRANTY WILL BE VALIDATED, ENSURING THAT YOUR EQUIPMENT WILL BE
PROTECTED SUBJECT TO THE TERMS AND CONDITIONS SET OUT HEREIN. IN THE EVENT WE NEED TO CONTACT YOU CONCERNING YOUR REGISTERED EQUIPMENT,
PRODUCT UPDATES, SERVICE BULLETINS, OR PRODUCT RECALLS, THE INFORMATION YOU HAVE PROVIDED ON THE PRODUCT REGISTRATION FORM WILL ENSURE
YOUR IMMEDIATE NOTIFICATION. DO YOUR PART AND LET US HELP YOU BY FILLING OUT YOUR PRODUCT REGISTRATION FORM.
!
IT IS THE OPERATOR’S RESPONSIBILITY TO INSPECT DOLLIES BEFORE EACH USE. INSPECTION SHOULD BE A PART OF THE OPERATOR’S DAILY
CIRCLE CHECK OF THE VEHICLE.
!
SERIES
TM
DOLLIES
DOLLY AXLES AND BREAK-OVER BAR
PAGE 1 OF 3
ANATOMY OF AN AXLE
ANATOMY OF A
BREAK-OVER BAR
SOFT GRIP
HANDLE
BREAK-OVER
BAR
POSITIVE CAMBER CAP PROFILE
AXLE END CAPS
FIVE SNAP BUTTON
POSITIONS
SNAP
BUTTON
TIRE PLATES
EXTENDS UP TO
85 INCHES
ITD0789

TM FOR MORE INFORMATION: www.intheditch.com | [phone] | [email protected]
FAILURE TO FOLLOW THE SAFETY GUIDELINES LISTED MAY RESULT IN VOIDING ANY APPLICABLE WARRANTY, SERIOUS BODILY INJURY, OR DEATH.
!
IT IS VERY IMPORTANT THAT YOU PROPERLY FILL OUT YOUR PRODUCT REGISTRATION FORM AT REGISTRATION.INTHEDITCH.COM TO REGISTER YOUR EQUIPMENT.
BY SUBMITTING THE INFORMATION WITHIN 15 DAYS OF YOUR PURCHASE, YOUR WARRANTY WILL BE VALIDATED, ENSURING THAT YOUR EQUIPMENT WILL BE
PROTECTED SUBJECT TO THE TERMS AND CONDITIONS SET OUT HEREIN. IN THE EVENT WE NEED TO CONTACT YOU CONCERNING YOUR REGISTERED EQUIPMENT,
PRODUCT UPDATES, SERVICE BULLETINS, OR PRODUCT RECALLS, THE INFORMATION YOU HAVE PROVIDED ON THE PRODUCT REGISTRATION FORM WILL ENSURE
YOUR IMMEDIATE NOTIFICATION. DO YOUR PART AND LET US HELP YOU BY FILLING OUT YOUR PRODUCT REGISTRATION FORM.
!
IT IS THE OPERATOR’S RESPONSIBILITY TO INSPECT DOLLIES BEFORE EACH USE. INSPECTION SHOULD BE A PART OF THE OPERATOR’S DAILY
CIRCLE CHECK OF THE VEHICLE.
!
HOW TO EXTEND AND DEPRESS AXLES
AXLE ADJUSTMENT
QUICK EXTEND AXLES
ITD aluminum telescoping axles
have been designed with large
corner radiuses and a domed
snap button to allow for a quick
extension of the axles.
Quick Extend:
1. Depressing the snap button
2. Place a foot on the axle cap to
keep the axle steady
3. Rotate axle pieces
4. Extend swiftly
5. Confirm that Axle Snap button
has been fully engaged
With a little practice, extending
axles to the correct hole can be
quick and easy.
PAGE 2 OF 3
GOOD SNAP
BUTTON
BENT SNAP
BUTTON
Ensure the snap buttons are not bent. If bent, replace
with snap buttons from ITD.
SNAP BUTTON
INSPECTION
Depress Extend
ADJUST DOLLY
AXLE LENGTH
Extend axles to the minimum length
required to span the width of the
vehicle, ensuring the thumb button
re-engages at the extended setting.
PROPER AXLE
ADJUSTMENT
IMPROPER AXLE
ADJUSTMENT
When you are extending the
length of the dolly Axles, it is
very important that you
extend them NO MORE THAN
4”past the side wall of the
vehicle tire.
More than 4” More than 4” BAD
✓ ✓
4” or less 4” or less
✓
GOOD
ITD0789

TM FOR MORE INFORMATION: www.intheditch.com | [phone] | [email protected]
FAILURE TO FOLLOW THE SAFETY GUIDELINES LISTED MAY RESULT IN VOIDING ANY APPLICABLE WARRANTY, SERIOUS BODILY INJURY, OR DEATH.
!
IT IS VERY IMPORTANT THAT YOU PROPERLY FILL OUT YOUR PRODUCT REGISTRATION FORM AT REGISTRATION.INTHEDITCH.COM TO REGISTER YOUR EQUIPMENT.
BY SUBMITTING THE INFORMATION WITHIN 15 DAYS OF YOUR PURCHASE, YOUR WARRANTY WILL BE VALIDATED, ENSURING THAT YOUR EQUIPMENT WILL BE
PROTECTED SUBJECT TO THE TERMS AND CONDITIONS SET OUT HEREIN. IN THE EVENT WE NEED TO CONTACT YOU CONCERNING YOUR REGISTERED EQUIPMENT,
PRODUCT UPDATES, SERVICE BULLETINS, OR PRODUCT RECALLS, THE INFORMATION YOU HAVE PROVIDED ON THE PRODUCT REGISTRATION FORM WILL ENSURE
YOUR IMMEDIATE NOTIFICATION. DO YOUR PART AND LET US HELP YOU BY FILLING OUT YOUR PRODUCT REGISTRATION FORM.
!
IT IS THE OPERATOR’S RESPONSIBILITY TO INSPECT DOLLIES BEFORE EACH USE. INSPECTION SHOULD BE A PART OF THE OPERATOR’S DAILY
CIRCLE CHECK OF THE VEHICLE.
!
Always inspect for any evidence of physical damage such as bending, cracking, and any defects.
If there is any damage, DO NOT USE and replace with an ITD axle and/or break-over bar.
BREAK-OVER BAR INSPECTION
PAGE 3 OF 3
!!
Ensure the break-over bar smoothly rolls over a flat surface. If there is hopping, the break-over bar is
bent. DO NOT USE and replace with an ITD break-over bar.
USING A BREAK-OVER BAR
PROPER AXLE
ADJUSTMENT
IMPROPER AXLE
ADJUSTMENT
Top View
✓
WARNING:
SNAP BUTTON MUST BE FULLY ENGAGED
BEFORE USE OR TRANSPORT
FAILURE TO ENGAGE SNAP BUTTON MAY
RESULT IN PERSONAL INJURY
(These instructions do not include all of the steps to load and unload, just basic
information about the break-over bar).
When loading/unloading, the vehicle should be
shifted into neutral position. The break-over bar
inserts into the receiver tube on the dolly.
When loading/unloading, grasp the far end of the break-over bar
with both hands and swing the bar in an arc to raise and lower the
dolly assembly.
THE OPERATOR SHOULD ALWAYS BE ON THE OPERATOR'S SIDE
OF THE BREAK-OVER BAR!
inside receiver tube.
INSERT BREAK-OVER BAR SWING BREAK-OVER BAR TO
RAISE DOLLY
O
P
E
R
A
T
O
R
S
I
D
E
Use both hands while lifting or lowering with
break-over bar at all times!
!
ALWAYS KEEP BOTH HANDS ON THE BREAK-OVER BAR WHILE
RAISING THE DOLLY!
EXTRA CAUTION SOULD BE USED IF LOADING OR UNLOADING ON
UNEEN PAVEMENT, LOOSE GRAVEL, SNOW, WATER, OR ICE!
THE SAME OPERATOR MUST LOAD AND UNLOAD THE DOLL.
CHANGES IN OPERATORS WILL RESULT IN UNFAMILIAR LOADS.
WHICH MAY RESULT IN SERIOUS INJURY!
1 2
ITD0789