Inbay 241178-01-1 User manual

All installation works have to be carried out by professional experts only.
The manufacturer / dealer can not be sued for direct of indirect damages caused from
unprofessional installtion. Technical changes possible.
Installation Manual
Inbay Universal Charging Cup
part-no.: 241178-01-1
For all vehicles equipped with
a cup holder ( diameter Ø 76 - 83 mm )
Suitable for smartphones with a maximum
width of 70 mm (including cover)
kit content
• (1) Inbay Charging Cup - wireless charging station in cup format
including 3 pairs of adjustable spacers and 1 m USB connector cable
• (2) 1 x external USB voltage transformer including connector cable
with fuse holder and 6,3mm blade connectors
• (3) 2x branch connectors 2,5mm² / 2x branch connectors 1 ,5mm²
• (4) spacers providing a perfect t of your smartphone
• (5) 1 x felt adhesive tape
1
2
3
4
5

The Inbay Universal Charger Cup is a wireless charging
cradle in cup-size format. Charging is done inductive
according to Qi-standard and enables charging of all
smartphones with Qi-compatible receiver going hand
in hand with a stable storing in the vehicle‘s cup-holder
=> Find a suitable cup holder in your vehicle
for the Charger Cup and rotate it to the desired
orientation
=> As example for a practice oriented orientation
we recommend a postition from where the display
of the smartphone is fully visible to the driver
=> In order to avoid visible cables the electrical
connection will be connected to the 12V
on-board electrical system of the vehicle
=> The cable routing of the Charging Cup
runs at the bottom or the side of the housing
=> Some vehicles have an opening at the bottom
of the cup holder or they are equipped with a
removable inlay or mat
In this case you can lead the USB connector cable of
the Charging Cup directly through the existing
opening of the center console
Inbay Universal Charging Cup www.inbay.systems

Inbay Universal Charging Cup www.inbay.systems
=> Position the Charging Cup to the desired
direction
=> If the cup holder has a solid bottom you
have to drill a hole (diameter of 18 mm)
in order to install the USB connector cable
The connection of the Charging Cup will
be carried or invisible at the 12V on-board
electrical system of the vehicle
=> Use the 12V on-board socket for power supply
=> unclip the center console and
pull/turn the console to reach the
12V on-board socket
Power supply is carried out via the
conncting cable of the 12V on-board socket
This connector oers enough power for
the Charging Cup with external voltage
transformator and is switched via ACC

=> Disconnect the plug of the on-board socket and
push down a bit the cable insulation
=> Mount the branch connectors on both cable
wires. Depending on the cable diameter
use the appropriate branch connectors:
• Cable diameter 2,5mm² => blue
• Cable diameter 1,5mm² => red
Caution! - check the correct polarity with
a voltmeter before you connect the USB
voltage transformer
Connection cables of the USB voltage transformer:
• red: +12V
• black: ground
=> Check functionality of Charging Cup:
Turning on ignition the LED has to light up red
When Inserting a Qi compatible smartphone
charging begins automatically and the
LED turns from red to blue
=> Re-install all removed covers and bezels
properly
=> Mount the USB voltage transformer at a
suitable place ( the USB voltage transformer
can be installed visible or invisible )
=> Plug in th USB connection cable of the Charging
Cup into the USB socket of the USB voltage
transformer
=> If neccessary secure the USB connection cable
with duct tape
=> Insure enough space for rods and streaks
of shifting gate before re-installing the center console
Inbay Universal Charging Cup www.inbay.systems
With the included spacers an optimal xation for
every smartphone even under strong side
acceleration can be carried out
=> A pair of spacers is already pre-installed.
If neccessary swap these against the appropriate
spacer pair depending on the size of the smartphone
going to be used
=> For adjustment of spacers release screws at
the outer side of the housing and slide spacers into
the desired position
=> Tighten screws carefully
=> Glue the attached felt adhesvie tape around
the housing of the Charging Cup in order provide
a tight t of the Charging Cup inside the cup holder
of the vehicle and to cover up the screws