Inficon Sensistor ISH2000 HySpeed User manual

EN
Operating Manual
Publication: INFICON AB - nina60e1-d (1304) - All information can be modified without prior notice
Hydrogen Leak Detector
Sensistor ISH2000
Instrument SW version 6.22
Probe SW version 1.08

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
OM-Sensistor ISH2000-EN-201304 3
EN
Contents
1 User information ........................................................................................................................... 6
1.1 Notes and safety notices..........................................................................................................6
1.2 Document outline....................................................................................................................6
1.3 Conventions used in this book.................................................................................................6
2 Description of equipment............................................................................................................. 7
2.1 Sensistor ISH2000....................................................................................................................7
2.2 Sensistor ISH2000C .................................................................................................................8
2.3 Sensistor ISH2000P..................................................................................................................9
3 Controls and connections...........................................................................................................10
3.1 Display ..................................................................................................................................10
3.2 Push-buttons ......................................................................................................................... 11
3.3 LEDs ...................................................................................................................................... 11
3.4 Ports and connections ...........................................................................................................11
4 Precautions .................................................................................................................................. 14
4.1 When working with gas ........................................................................................................14
4.2 Hydrogen Tracer Gas for leak detection ................................................................................. 15
4.3 Interferences .........................................................................................................................15
5 Working principle....................................................................................................................... 16
5.1 Gas Sensor Technology .........................................................................................................16
5.2 Condition for leak detection .................................................................................................. 16
5.3 Leak Detection mode.............................................................................................................16
6 Operating the detector............................................................................................................... 17
6.1 To Detect Leaks .................................................................................................................... 17
6.2 To Locate Leaks ....................................................................................................................17
6.3 To Quantify Leaks .................................................................................................................18
7 Calibrate the leak detector......................................................................................................... 19
7.1 Introduction ..........................................................................................................................19
7.2 Calibration Leak or Calibration Gas........................................................................................ 19
7.3 Unit Conversion.....................................................................................................................19
7.4 Calibration procedure............................................................................................................20
7.5 Calibration value with Calibration leak................................................................................... 20
7.6 Calibration value with Calibration gas.................................................................................... 21
8 Reference section ........................................................................................................................ 22
8.1 Menu system.........................................................................................................................22
8.2 Button functions....................................................................................................................23
8.3 Stored values and setups .......................................................................................................23
8.4 Engineering format................................................................................................................23
8.5 Change Test Mode ................................................................................................................ 23
8.6 Calibration ............................................................................................................................23
8.7 Locating Mode Settings ......................................................................................................... 27
8.8 Measuring Mode Settings......................................................................................................29
8.9 APC Settings* ....................................................................................................................... 31
8.10 Display Settings ..................................................................................................................... 32
8.11 General Settings .................................................................................................................... 32
8.12 Service Settings ..................................................................................................................... 34
8.13 Combined Mode ................................................................................................................... 36
8.14 Probe ....................................................................................................................................36
8.15 Probe Control Port................................................................................................................. 37
8.16 Printer port............................................................................................................................39
8.17 Sensistor ISH2000P installation ..............................................................................................45
8.18 Default parameters................................................................................................................46
9 Trouble-shooting......................................................................................................................... 49
10 Sensistor ISH2000 specifications................................................................................................50
11 Spare parts and accessories........................................................................................................ 52
12 Support by INFICON.................................................................................................................... 53
12.1 How To Contact INFICON ......................................................................................................53
12.2 Returning your instrument to INFICON...................................................................................53

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
4 OM-Sensistor ISH2000-EN-201304
EN 13 Menu Overview .......................................................................................................................... 54
14 Declaration of conformity .......................................................................................................... 56
15 Recycling ...................................................................................................................................... 57

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
OM-Sensistor ISH2000-EN-201304 5
EN
Welcome to Sensistor ISH2000
Dear customer,
You have just bought an INFICON Hydrogen Leak Detector Sensistor ISH2000. The
Sensistor ISH2000 is an extremely sensitive and selective detector for hydrogen gas (H2).
It is especially designed for leak detection using Hydrogen Tracer Gas (Hydrogen diluted
with Nitrogen down to a safe concentration) which is the most effective and economical
tracer gas for leak testing.
Sensistor ISH2000 detects hydrogen in air at atmospheric pressure with no need for
vacuum pumping. It is especially suitable for applications where high sensitivity and
selectivity is required in combination with simplicity, reliability and low cost.
This product complies with the requirements of European
Directives, listed in the Declaration of Conformity found on
page 56 in this document. These Directives are amended by
Directive 93/68/E.E.C (E.C. Marking).
Copyright/Intellectual property
The use of INFICON AB products are subject to copyright and
intellectual property rights in force in any jurisdiction.
All rights reserved, including copying this document in whole
or in any part without prior written authorization from
INFICON AB.
Though INFICON AB believes reasonable efforts have been
made to ensure the accuracy of the information contained in
the document, it may include inaccuracies or typographical
errors. INFICON AB reserves the right to change the
information inside the document without further notice.

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
6 OM-Sensistor ISH2000-EN-201304
EN 1 User information
Read this user manual carefully before using the Sensistor ISH2000.
1.1 Notes and safety notices
This manual contains warnings and cautions concerning the safe use of the product.
See definitions below.
Note: A Note is used to indicate information that is important for trouble-free and optimal
use of the Sensistor ISH2000.
1.2 Document outline
The document is divided in two main parts:
• Getting started
• Reference section
The Getting started part consists of step by step case examples, explaining how to use
the Sensistor ISH2000 in a variety common situations. The Reference section consists of
in depth explanation and additional information, which completes the user manual
with all relevant information.
1.3 Conventions used in this book
In this user manual the following text style (hardware command) is used for references
to hardware commands or button labels, while this text style (software command) is
used for references to software commands and menu choices.
WARNING!
Warning indicates a hazardous situation which, if not
avoided, could result in death or serious injury. It is
important not to proceed until all stated conditions
are met and clearly understood.
CAUTION!
Caution indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury. It is
important not to proceed until all stated conditions
are met and clearly understood.
NOTICE!
Notice indicates instructions that must be
followed to avoid damage to the Sensistor
ISH2000 or other equipment.

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
OM-Sensistor ISH2000-EN-201304 7
EN
2 Description of equipment
Sensistor ISH2000 can be purchased in one of three versions. A desktop model
(Sensistor ISH2000), a battery operated model (Sensistor ISH2000C), and a panel
mount model (Sensistor ISH2000P).
2.1 Sensistor ISH2000
Sensistor ISH2000 is equipped with a number of powerful functions making it very
easy to integrate in a semi or fully automatic test system. The functions range from
output of all necessary status signals and printer/communication port to an
advanced Active Probe Control system (APC). This makes the detector capable of
controlling advanced sample collecting devices down to simple test fixtures.
Fig 2-1. The desktop model consists of seven parts.
Item Description
1Detector instrument
2Hand Probe P50 (shown) or Active Probe with
sensor
3Probe cable C21
4Power cable (the power cable is country specific
and may differ)
5User manual (not shown)
6User manual in electronic form
(on CD or USB memory stick)
7Product return form (not shown)
1
23

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
8 OM-Sensistor ISH2000-EN-201304
EN 2.2 Sensistor ISH2000C
The battery operated model, Sensistor ISH2000C, has all the Sensistor ISH2000
features apart from the APC system. This means that only passive probes (for
example Hand Probe P50) can be used. This is due to power management control.
The battery, a Li-ion battery at 14.8 V, can not support the current required to
operate external probes.
On the display a symbol in the upper right corner shows the battery charge status.
Sensistor ISH2000C will operate for 14 hours on a fully charged battery with
screensaver and mute function. And 9 hours without screensaver and mute function.
One hour charging will give about one hour of operating time. This can be done
when necessary, but it is important to regularly fully charge the battery.
Fig 2-2. The battery operated model consists of seven parts.
Item Description
1Detector Instrument
2Hand Probe P50 (shown) or P50-Flex
3Probe cable C21
4Carrying case
5Battery charger (the battery charger are country
specific and may differ, not shown).
6User manual (not shown)
7User manual in electronic form
(on CD or USB memory stick)
8Product return form (not shown)
1
2
3
4

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
OM-Sensistor ISH2000-EN-201304 9
EN
2.3 Sensistor ISH2000P
The panel mount model, Sensistor ISH2000P, has identical features of the Sensistor
ISH2000.
The difference is that the Sensistor ISH2000P can be installed in the operator’s panel
or any other flat surface. The instrument operates on an external +24VCD power
supply, provided by the customer. Mounting brackets and a panel rubber seal are
delivered with the detector. See “Sensistor ISH2000P installation” on page 45.
Fig 2-3. The panel mount model consists of seven parts.
Item Description
1Detector instrument
2Brackets (not shown)
3Screws (not shown)
4O-rings seal (not shown)
5User manual (not shown)
6User manual in electronic form
(on CD or USB memory stick)
7Product return form (not shown)
1

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
10 OM-Sensistor ISH2000-EN-201304
EN 3 Controls and connections
The controls and connections are discussed and shown in this chapter.
Fig 3-1. Sensistor ISH2000 controls and indicators
3.1 Display
The display shows:
• Indicator bar in Locating Mode and the figures in Measuring Mode.
• Eight main menus. Their positions are indicated on a horizontal scale. Change from
one menu to another using the < and >buttons.
• Main menus have sub-menus, which are also indicated by horizontal scales and can
be selected using the <and >buttons.
• Scales for setting numeric values, languages, etc.
• Messages.
Sensistor ISH2000C:
• A battery status indicator in the upper right corner.
Item Description
1Display
2Loudspeaker
3Control push-buttons
4Earphone socket
5Probe connector
6LEDs
(1.00E+01)
0.0
cc/s
Air
23
6
45
Sensistor ISH2000
1
Volume Sens Cal Menu
Combined Mode

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
OM-Sensistor ISH2000-EN-201304 11
EN
3.2 Push-buttons
The functions of the push-buttons are shown at the lower edge of the display. In this
manual the buttons are numbered, from left to right, 1, 2, 3, and 4. The push-buttons
are used to:
• Change from one menu item to another using the < and >buttons.
• Press Enter to move down to the nearest sub-menu.
• Press Save to save the set value.
• Press Undo to restore the previously set value.
• Press Esc to move up to the nearest higher level(s).
• Shortcut to reach functions as Volume Sensitivity (Sens), Calibration (Cal) and
Menu.
3.3 LEDs
The two LEDs indicate the status of the instrument as follows:
• Green flashing slowly, during warming up phase.
• Green fixed light indicates that instrument is ready and hydrogen signal is below
Reject Level limit.
• Periodically flashing green or red calls for calibration.
• Alternating red and green light while the instrument establishes probe
communication.
• Red fixed light together with Reject on display means the instrument has detected a
leak larger than the set Reject Level limit.
• Red flashing rapidly, check message on screen. (See “Trouble-shooting” on
page 49.)
3.4 Ports and connections
The ports and connections are shown in Figure 3-2 on the next page.
NOTICE!
Always connect all four wires to the Power connector to
24VDC in order to operate.

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
12 OM-Sensistor ISH2000-EN-201304
EN Sensistor ISH2000
Fig 3-2. Sensistor ISH2000 ports and connections (rear view).
Sensistor ISH2000C
Fig 3-3. Sensistor ISH2000C ports and connections (rear view).
Item Description
1Data output
2Probe control port
3Fuse
4Power switch
5Power input, 100-240 VAC
6Screw hole for mounting plate
1
2
3
45
6
123
4
5
6
Rear View
123
4
5
6
Item Description
1Power switch
2Printer port
3Power input (From Battery charger)
4Screw hole for mounting plate
12
3
4

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
OM-Sensistor ISH2000-EN-201304 13
EN
Sensistor ISH2000P
Fig 3-4. Sensistor ISH2000P ports and connections (rear view).
Item Description
1Probe connection
2Ground screw
3Power input (24 VDC)
4Probe control port
5Printer port
1234
5

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
14 OM-Sensistor ISH2000-EN-201304
EN 4 Precautions
Read this user manual carefully before using the instrument. Hydrogen Leak
Detector Sensistor ISH2000 is extremely selective. Only Hydrogen Sulphide
(extremely toxic) gives a comparable response to hydrogen.
4.1 When working with gas
The normal risks associated with working with all compressed gases must be
considered.
Before connecting tracer gas: confirm that the connectors and test object is
designed for working at the test pressure.
Note: INFICON AB can not take any responsibility for the consequences arising from the
inappropriate use of certain test pressures.
WARNING!
Pure hydrogen is a flammable gas. Only use
ready-made Hydrogen Tracer Gas of 5%
Hydrogen in Nitrogen. This is a standard
industrial gas mixture used in various industrial
applications.
Note: Whenever the word Hydrogen is used in this
manual it implies that the hydrogen gas is safely
mixed with Nitrogen in the proportions 5% H2-
95% N2.
WARNING!
Since the tracer gas mix contains no oxygen,
releasing large amounts of gas in a confined
space may lead to asphyxiation.
WARNING!
Compressed gases contain a great deal of stored
energy. Always carefully secure gas bottles
before connecting pressure regulator. Never
transport gas bottle with the pressure regulator
fitted.
WARNING!
Pressurising objects at too high pressures can
result in a burst object. This in turn can result in
serious injury or even death.
Never pressurise objects that have not
previously been burst tested or otherwise
approved for the chosen test pressure.

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
OM-Sensistor ISH2000-EN-201304 15
EN
Pressure shocks might cause strong sounds which can cause impairment of hearing.
Check that all relevant legislation and safety standards are complied with before
putting Sensistor ISH2000 into service.
4.2 Hydrogen Tracer Gas for leak detection
When pure hydrogen gas is released in air its flammability range spans from 4% to
75% of hydrogen in air. Below 4% there is insufficient chemical energy available for
a flame to occur. Above 75% hydrogen there is not enough oxygen left to support a
flame.
When, for example, a mixture of less than 5.5% hydrogen in nitrogen mixes with air
there is not sufficient energy to support a flame, irrespective of the ratio of air-to-
gas.
When a mixture of more than 5.5% hydrogen in nitrogen is released into air there is
a region of ratios of air-to-gas where the mixture is flammable. When, for example,
a mixture of 10% hydrogen in nitrogen mixes with air there is still very little energy
available. Only in exceptional circumstances can a flame be self-supporting.
However, such mixtures cannot detonate.
4.3 Interferences
Most tracer gas methods suffer from some sort of interference. Either the detector is
sensitive to other gases or vapors, or there are other sources of the gas present to
which the detector is sensitive.
Some examples of possible hydrogen sources:
• Engine exhaust
• Battery charging stations
• Cigarette smoke
• Breathing air
• Human flatulence
• Scratching on aluminum surfaces
WARNING!
Hydrogen/nitrogen mixtures containing
approximately more than 15% hydrogen can
detonate when mixed in certain proportions
with air.
NOTICE!
Never make your own mixtures. Only use ready-
made mixtures or use a certified hydrogen/
nitrogen mixture mixer installed by your gas
supplier.

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
16 OM-Sensistor ISH2000-EN-201304
EN 5 Working principle
5.1 Gas Sensor Technology
The Sensistor ISH2000 leak detector is using an extremely sensitive hydrogen gas
sensor based on a metal-oxide-semiconductor field-effect-transistor (MOS-FET).
The gas sensitivity appears when hydrogen absorbs into the sensor through a metal
alloy (metal hydride) layer.
Only hydrogen can diffuse into the metal and this makes the sensors practically
insensitive to other substances that do not contain free hydrogen molecules.
The signals from the sensors are processed by a microprocessor which also controls
the sensor temperature with high accuracy, and other sensor diagnostics in order to
ensure perfect functionality. It also automatically compensates for background gas.
5.2 Condition for leak detection
To use the leak detector the test object must be filled and pressurized by tracer gas
(95% N2/ 5% H2) to get a gas flow through the leak. The tracer gas is a standard
welding gas of industry quality, easy to obtain at low cost. The generic name is
Forming Gas. Appropriate gas filling equipment can be obtained from the leak
detector supplier.
Be careful of how tracer gases are handled after use. Released tracer gas
contaminates the surrounding air with hydrogen and can complicate the following
measurements for a time. Ensure that the tracer gas is ventilated away from the
target area, preferably to the outside of the building.
5.3 Leak Detection mode
The detector operates in three modes:
• Locating Mode is mainly used for detecting and locating leaks but not quantifying
them.
• Measuring Mode measures the concentration of hydrogen.
• Combined Mode, (default mode) which is a combination of Locating and Measuring
Mode.
The Locating Mode operates continuously while the Measuring Mode determines
the hydrogen concentration (and calculates a corresponding leak rate) in a step
measurement. Locating Mode gives no numbers. It therefore needs no actual
calibration. The sensitivity of the sound signal and the moving bar on the display is
set manually or automatically, see below.
When using the instrument in Measuring Mode, it must be calibrated as described.
See “Calibrate the leak detector” on page 19 in order to give correct figures.

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
OM-Sensistor ISH2000-EN-201304 17
EN
6 Operating the detector
6.1 To Detect Leaks
If all you wish to do is to detect the presence of a leak, that is, find out whether there is
a leak or not, then use the Locating Mode (or use the Locating bar in Combined
Mode). The definition of Leak/No Leak will then simply be ”A leak is a leak when it can
be detected by the detector, set to a specific sensitivity”.
To set up:
The operation in Locating Mode is not quantitative. The audio and visual signal will
increase and decrease with the gas concentration. Therefore, there is no actual
calibration to be done, but rather a setting of the sensitivity to a desired level.
A typical set-up procedure for Locating Mode is:
• Set up a Calibration leak which corresponds to the smallest leak you wish to detect.
• Put the probe close to the Calibration leak and note approximately what reaction
you get (no reaction, small, medium, high, full scale) within the first few seconds.
• Set the sensitivity. This can be done permanently under the menu Locating Mode
Settings or temporarily as a Direct Sensitivity Adjustment on the display (unless
you have set this function to OFF under the Locating Mode Settings menu).
There is also an Auto ranging function which can be selected under the Locating
Mode Settings menu.
Note: If the Locating Mode is used and the alarm function is required to be
activated at a particular calibrated level, then the unit must be calibrated in
accordance with the instructions, see “Calibrate the leak detector” on
page 19. The reason for this is that the alarm is based on the Measuring
Mode when the Locating Mode is displayed.
6.2 To Locate Leaks
Note: The Locating Mode (or use the Locating bar in Combined Mode) is used to
locate leaks. This mode is semi-quantitative, that is, it gives an audio and visual
signal which increases as a leak is approached (a higher gas concentration)
and decreases as you move the probe away from the leak. It does not display
figures. In this mode of operation leaks can easily be detected using a
sensitivity which can be preset. See “Sensitivity” on page 28 and “Direct
Sensitivity Adjustment” on page 28.
Leaks can be located very accurately, even when there are other leaks nearby. If, for
example, you are trying to locate a leak on a product and the product has a major
leak, then you will get an audio signal as soon as the probe is placed close to the
product. When the probe is moved around and over the product, the signal will
increase as the probe approaches the leak. If the signal goes out of scale, simply
reduce the sensitivity setting to bring the signal within the scale. Working with the
sensitivity setting this way you will be able to locate multiple leaks that are in close
proximity to each other.
Note: Working inside a confined space such as, for example, a cabinet or a narrow
passage on a combustion engine there is a risk that the background
concentration accumulates to levels close to the upper detection limit of the
detector. In such case it will not be possible to locate leaks as easily as in open
spaces.

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
18 OM-Sensistor ISH2000-EN-201304
EN Hint: It is good practice to detect a leak, locate it, and immediately remove the probe
to avoid saturation. The probe is not damaged by the exposure but it will recover more
slowly. After excessive exposure it will be less sensitive for a short period of time.
6.3 To Quantify Leaks
The Measuring Mode (or use the figures in Combined Mode) is used for measuring
the size of a leak (or the concentration of a gas sample). To be able to do this
measurement and obtain correct values, the instrument must first be calibrated using
the calibration function.
In the Measuring Mode the detector determines the gas concentration from the
change, as the probe goes from being exposed to background to being exposed to a
certain gas concentration. The detector does not continuously monitor the gas
concentration but takes just one reading instead. Another suitable alternative name
for this mode could be Sampling Mode. It is important to keep this in mind when using
the detector in this mode.
In Measuring Mode the probe should be moved directly from a background situation
to the test point. The size of the leak in cc/s, or any other selected units, is shown on
the display. The probe can and should be removed from the measuring point as the
measured value steady and remains on the display. The period during which the
measured value is displayed can be adjusted in the Measuring Mode Settings menu.
The leak detector operates in the range 0.5 - 2000 ppm H2giving linearity between 0.5
and 500 ppm. To obtain greatest accuracy over this range, follow the calibration
recommendation. See “Calibrate the leak detector” on page 19.
CAUTION!
• Do not open detector! Service of this equipment may only be carried out by ser-
vice organizations authorized therefore by INFICON, Sweden.
• If the detector gets outer damage it must be controlled and repaired by service
organization authorized by INFICON.
• Do not expose the probe to a hydrogen concentration higher than 0.1% when
the instrument is not put into operation, this might damage or destroy the probe
sensor.
• When the instrument is put into operation the sensor withstands temporary
exposure to hydrogen concentration up to 100%. Avoid long exposures to high
concentrations.

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
OM-Sensistor ISH2000-EN-201304 19
EN
7 Calibrate the leak detector
7.1 Introduction
The leak detector is the instrument and the probe together.
This section of the operating manual consists of step by step examples on how to
calibrate the detector in the most common cases. For more about the calibration
routine, see the reference section.
The instrument must be calibrated by using the integrated calibration function to
make sure it displays the correct values in Measuring Mode. After calibration, the
instrument will show the correct measured values on the display in Measuring Mode
and in Combined Mode. The calibration parameters will be stored in the probe.
7.2 Calibration Leak or Calibration Gas
There is a possibility to calibrate the detector by using Calibration Gas or a
Calibration Leak.
A Calibration Gas contains a well-defined concentration of Hydrogen gas mixed
with air. A Certificate will normally follow the gas bottles. Calibration Gas can be
ordered from local gas suppliers.
A Calibration Leak is a well–defined gas leak. The Calibration Leak should be fed by
the same gas used in the detection test and with a gas pressure defined in the
Calibration Leak certificate. Calibration Leak can be ordered from the detector
provider.
Choose a calibration leak or calibration gas size, as follows:
• Same or higher than the Reject Level (but maximum 10 times higher)
• In one of the following ranges:
5 to 400 ppm H2
1x10-5 to 4x10-3 cc/s (mbarl/s) defined for air
3 to 120 g/yr defined for R134a
Please contact the provider of the detector for help to select optimal calibration
reference for your application.
7.3 Unit Conversion
When using flow units (other than “ppm” and “custom”), the instrument
automatically converts between the calibration unit and the measurement unit. The
conversion is saved in the Correlation value and is updated when Calibration Unit or
Measuring Unit is changed. Leak Gas and Displayed Gas will not change Correlation
Value, but will have effect on the measured figures.
If “ppm” or custom unit is chosen (Measuring or Calibration Unit), the Correlation
Value must be set by operator. To set Correlation Value go to menu General
Settings.
Correlation Value can be modified even otherwise.

Hydrogen leak detector Sensistor ISH2000 - Operating Manual
20 OM-Sensistor ISH2000-EN-201304
EN 7.4 Calibration procedure
Before calibration, the Calibration Value, Calibration Unit and Leak Gas in the Calibration
Menu must be set. See “Calibration value with Calibration leak” and “Calibration
value with Calibration gas” below.
Let the instrument be in operation for at least 30 minutes to achieve the best
conditions for a calibration.
When calibrating, do the following steps:
1. Go to Menu then Calibration/Calibrate/Enter or just push the button “Cal” on the
main screen.
2. Expose the probe to background.
3. Push the Start button or push the probe button.
4. Expose the probe for the Calibration gas/leak
The probe does not have to be exposed to the calibration gas during the entire
Calibration Time (the time set in the Calibration menu while the bar is moving). The
instrument only measures the change as the probe goes from the background air to
calibration gas.
While the calibration time bar is moving, the probe should be exposed to the
Calibration gas or Calibration leak. Wait until the instrument shows “Gas detected”
and gives a sound signal. Repeat until you can save the calibration by pressing Save or
probe button. If the calibration is not saved, the instrument will revert to the
previous value after one minute.
Note: You will need to repeat the gas exposure procedures 2-3 times to get
Calibration OK after changing setup or probe. The text “Calibration failed! Check
leak/gas and sensor status” (or a custom text) will appear after 5 attempts.
• Allow at least 30 seconds between each exposure for best accuracy!
• If the message “No gas or Unstable Signal” is displayed repeatedly - go back to
Locating Mode and check functionality.
• If “Calibration in progress. Please repeat again” is displayed it means that the
measured value deviated more than 10% from the previous calibration. Repeat
the calibration procedure.
7.5 Calibration value with Calibration leak
When measuring leak flow you will, in normal cases, calibrate the detector with a
Calibration leak.
Set the Calibration Value equal to the calibrated flow of your Calibration leak. Also
set the Calibration Unit to the same unit as that used to express the leak rate of the
Calibration leak. Finally set the Leak Gas that the leak is defined for. These values
can be found on the calibration certificate issued for the leak. Finally set the Leak
Gas that the leak is defined for. These values can be found on the calibration
certificate issued for the leak.
Example: Calibration leak rate is defined to: 4.2E-5 mbarl/s for Helium.
1- Set Calibration Value = 4.2E-05.
2- Set Calibration Unit = “mbarl/s