Infineon TRAVEO II CPU BOARD User manual

www.infineon.com
Please note that Cypress is an Infineon Technologies Company.
The document following this cover page is marked as “Cypress” document as this is the
company that originally developed the product. Please note that Infineon will continue
to offer the product to new and existing customers as part of the Infineon product
The fact that Infineon offers the following product as part of the Infineon product
portfolio.
Continuity of document content
portfolio does not lead to any changes to this document. Future revisions will occur
when appropriate, and any changes will be set out on the document history page.
Continuity of ordering part numbers
Infineon continues to support existing part numbers. Please continue to use the
ordering part numbers listed in the datasheet for ordering.

CYTVII-B-H-8M-320-BGA CPU BOARD QUICK START GUIDE
TRAVEO II CPU BOARD
Kit Contents:
1. Traveo II CPU Board CYTVII-B-H-8M-320-BGA CPU BOARD Rev.A
2. Type-B Mini USB Cable
3. 12V AC-DC Universal Power Adapter
4. Quick Start Guide (this document)
5. Screws and Spacers

TRAVEO II CPU BOARD
• Ensure that the Reset Jumper (J27) is inserted
CYTVII-B-H-8M-320-BGA CPU BOARD QUICK START GUIDE
•Ensure that Jumpers J14, J20, J21, J6, J9, R35 are
inserted. Jumpers J16, J17, J18, J19 should be in
position 1-2. Jumpers J22, J15 should be in position 2-3
•Connect an appropriate programming tool (IAR/GHS), to
one of the debugging interfaces -(J4, J5, J12, J13)
Use an appropriate IDE on a PC, to load a rmware SREC le into the device ash successfully.
The LED Blink Firmware is available in the Release-Package
• Connect the 12V Adapter to J10 connector. Toggle the
switch SW2 to ON position to power ON the board
12
4
3

CYTVII-B-H-8M-320-BGA CPU BOARD QUICK START GUIDE
For the following documentation:
• User Guide
•Schematic
• Sample Driver Library (SDL)
• Software examples
Please use the Cypress Customer Support Portal.
Instructions:
• The Traveo II CPU Board can be used standalone to evaluate limited features of the Traveo II MCU
•The board can be used with Body Controller Base Board, to evaluate all the features of the MCU
TRAVEO II CPU BOARD
•To know more about the Base Board and compatibility, please use the Cypress Customer
Support Portal. (cypress.com/support)

CYTVII-B-H-8M-320-BGA CPU BOARD QUICK START GUIDE
TRAVEO II CPU BOARD
Traveo II CPU Board Details
1. MIPI-10-Cortex Debug Connector
2. MCU TAP Controller Reset LED
3. MIPI-20-Cortex Debug + ETM Connector
4. SW1 – User Switch
5. J2 – Jumper for User Switch
6. J3 – Jumper for User LED
7. LD1 – User LED
8. MCU Power Jumpers
9. Cypress PMIC
10. Power LEDs
11. SW2 – Power Switch
12. J1 – Jumper for GND Probe
13. J10 - Power Jack (12 V)
14. 1.1V LDO
15. 2.5V LDO
16. Gigabit Ethernet Controller
17. RJ45 Gigabit Ethernet Connector
18. UART Rx and Tx LEDs
19. USB Type-B Mini Connector
20. Cypress USB-Serial Controller
21. Rx and Tx Jumpers
22. Quad SPI 256M Flash Memory
23. 512M Hyper Flash Memory
24. 64M Hyper DRAM
25. 1.8V LDO
26. U6 – Cypress TVII-B-H-8M MCU
27. SD Card Connector
28. J34 – Audio Jack
29. Audio Codec
30. SW3 – MCU Reset
31. J27 - MCU Reset Jumper
32. LED7 – MCU Reset LED
33. D-SUB 9 Automotive Ethernet Connector
34. Automotive Ethernet Controller
35. 20 Pin IDC – Arm Standard JTAG Connector
36. Mictor-38- Arm ETM Mictor Connector
1 2 3 4 5 6 7 8 9 10 11 12
13
14
15
16
17
18
19
20
21
2223242526272829
30
31
32
33
34
35
36
© 2019-2021 Cypress Semiconductor Corporation. An Inneon Technologies Company.
All rights reserved. All trademarks or registered trademarks referenced herein
are the property of their respective owners. 002-27228 Rev.*A