Inflight Fitness Liberator User manual

LIBERATOR ASSEMBLY INSTRUCTIONS
IMPORTANT NOTICES
Read all warning labels, the instruction placard and this manual before attempting to use this machine. Always consult
your physician and an exercise professional before beginning any exercise program/regimen.
Before any test or use check for proper assembly of the machine including (but not limited to): bolts and other hardware
fastened properly, cables in pulley grooves and routed correctly. For safety use the top weight only for the first machine
movement.
Maintain your machine in good working order by following the maintenance schedule provided on the equipment.
It is strongly recommended that a qualified dealer assemble this
Liberator Multi-Gym.
Should there be any question during assembly contact your authorized Inflight Fitness dealer or call direct to 714 821 4177.
Before beginning assembly read this instruction manual thoroughly. Unpack and verify all parts and hardware quantities against
the parts and hardware lists.
Follow the assembly steps in sequence. Failure to follow the order of assembly will result in disassembly later and possible
damage to the machine components.
The 3/8” nuts provided with this machine are “centerlocking”. They provide a more secure assembly than nylon locking nuts.
Please note they do require more force to tighten than nylon locking nuts.

Note: In steps A thru G do not fully tighten bolts until instructed
to tighten.
A
. Attach MAIN UPRIGHT to MAIN FRAME and BASE FRAME using
2-3" bolts, 2-2 3/4" bolts, 8-washers and 4-locknuts.
B. Attach "pulley end" of MID FRAME to MAIN UPRIGHT, MAIN
FRAME and BASE FRAME using 2-3 1/2" bolts, 4-washers and 2-
locknuts.
C. Attach MULTI-LEG BASE to BASE FRAME and MID FRAME using
2-3" bolts, 4- washers, and 2-locknuts.

Note: For steps D and E it is strongly recommended that
another person be present to assist.
D. Attach TOP FRAME to MAIN UPRIGHT using 2-3" bolts, 4-
washers, and 2-locknuts.
E. Attach TOP BEAM between flanges of MAIN UPRIGHT and
TOP FRAME using 4-3" bolts, 8-washers and 4-locknuts.
F. Attach MAIN BRACE #1 to BASE FRAME and TOP
FRAME using 2-3 1/2" bolts, 4-washers and 2-locknuts. See
picture for orientation of holes.
G. Attach MAIN BRACE #2 to BASE FRAME and TOP
FRAME using 2-3 1/2" bolts, 4-washers and 2-locknuts. See
picture for orientation of holes.
Note: Tighten all bolts installed in steps A-G.

A
. Insert GUIDE RODS into holes in BASE FRAME.
B. Place 1 weight stack donut
on each GUIDE ROD and allow to slide
down to top of BASE FRAME.
C. Apply lubricant to the GUIDE RODS from the WEIGHT STACK
DONUTS to the tops of the GUIDE RODS.
D. Making sure that WEIGHT LABEL INDENT is facing out from center of
machine, install 5-15 LB. WEIGHTS, then 10-10 LB. WEIGHTS and then
5-5 LB. WEIGHTS.
IMPORTANT: Find the TOP WEIGHT with the cable marked MULTI-LEG
UPPER for this station.
E. Place TOP WEIGHT onto the GUIDE RODS with cap screw facing out
from the machine, and allow to slide down to the weight stack.
F. Attach CENTER STACK GUIDE ROD BRACKET to TOP FRAME
using 2-2 3/4" bolts, 4-washers and 2-locknuts. See picture for orientation
of bracket. Ti
g
hten bolts.

IMPORTANT: Before assembling the weight stacks locate the
TOP WEIGHTS pre-assembled with the cable marked for the
position you are assembling (marked CHEST PRESS for the
CHEST PRESS station and marked LAT/SHOULDER for the
LAT/SHOULDER station).
G. Repeat procedure A through E for remaining 2-weight stacks.
H. Attach MULTI-FUNCTION G.R. BRACKET to left side of TOP
FRAME using 2-2 3/4" bolts, 4-washers and 2-locknuts. See
picture for orientation of bracket. Tighten bolts.
I. Attach MULTI-FUNCTION G.R. BRACKET to right side of
TOP FRAME using 2-2 3/4" bolts, 4-washers and 2-locknuts.
See picture for orientation of bracket. Tighten bolts.

Note: For step A it is strongly recommended that another
person be present to assist.
A
. Attach CHEST PRESS to bracket on TOP BEAM using 2-pillow
block bearings, 4-1 1/2" bolts, 8- washers and 2-locknuts. Make
sure that set screw side of bearings are facing outward. Finger
tighten only.
B. Align the PRESS ARM by viewing from front and side, and
adjusting as necessary. Tighten bolts and set screws.
C. Attach CHEST PRESS STOP to MAIN UPRIGHT using 2-3 3/4"
bolts, 4-washers and 2-locknuts. Tighten bolts.
D. Attach BACK PAD FRAME to MAIN UPRIGHT using 2-3 3/4"
bolts, 4-washers and 2-locknuts. Tighten bolts.

A
. Attach SEAT FRAME to MAIN UPRIGHT using 3-3 3/4" bolts, 6-washers
and 3-locknuts. See picture for correct location of holes.
B. In the remaining hole of SEAT FRAME, install 1-5 1/2" bolt and 1-washer
through SEAT FRAME and MAIN UPRIGHT. Then install onto the bolt 1-1/2”
Barrel Spacer, 1-4 ½” pulley, 1-“L”-Cable Retainer, 1-washer, and 1-locknut.
Components must be installed in that order.
Tighten bolts installed in step A, but not bolt from step B.
C. Install 2-FLANGE BEARINGS in lower holes of BEARING PLATES on
MAIN UPRIGHT using 2-4 1/4" bolts, 4-washers and 2-locknuts. Do not
tighten.

D. Attach SHOULDER PRESS to MAIN UPRIGHT (with
handles angled downward) using 1-10 1/2" shaft. Tighten
shaft collars, but not set screws in flange bearings.
E. Align SHOULDER PRESS by viewing from front and
rear, adjusting as necessary. Tighten bolts and set screws.

A
. Install 2-FLANGE BEARINGS in upper holes of BEARING
PLATES on MAIN UPRIGHT using 2-4 1/4" bolts, 4-washers and
2-locknuts. Do not tighten.
Note: Recommend help for step B and E.
B. Attach LAT PULL to MAIN UPRIGHT (with handles angled
downward) using 1-10 1/2" shaft. Tighten shaft collars, but not set
screws in flange bearings.
C. Align LAT PULL by viewing from front and rear, adjusting as
necessary. Tighten bolts and set screws.

D. Attach 1 end of LAT SPRING to bracket located on TOP FRAME
using 1-1 1/4" bolt and 1-locknut.
E. While having an assistant hold LAT PULL all the way up, use both
hands to stretch LAT SPRING down and slide end onto LAT HOOK
located on LAT PULL.

A
. Attach MULTI-LEG MAIN to MULTI-LEG BASE using 2-2
3/4" bolts, 4-washers and 2-locknuts. Do not tighten.
B. Attach MULTI-LEG BRACE to MULTI-LEG MAIN and
MAIN BRACE #1 using 2-2 3/4" bolts, 2-1 3/4" bolts, 8-
washers and 4-locknuts.
Tighten bolts from steps A and B at this time.
C. Attach LEG EXT. UPRIGHT FLATS to MULTI-LEG MAIN
using 2-4 1/4" bolts, 4-1/2" barrel spacers, 4-washers and 2-
locknuts. Do not tighten.

BACKPAD SUPPORT TUBES
1-1/2"X 5 1/2" BOLT
2-1/2" THIN WASHERS
1-1/2" THIN NYLOCK NUT
F
LEG EXT.
ROTATING ARM
2-1" BUTTONHEAD
BOLTS
2 - WASHERS
E
BENT HANDLES
2-3"BOLTS
4-WASHERS
2-LOCKNUTS
D
10b
Multi-Leg Assembly LIBERATOR

A
. Attach FOOTPLATE to LOW PULLEY ATTACHMENT TUBE
and MULTI-LEG MAIN using 2 – 4” bolts, 4 – washers, and 2 –
locknuts. Tighten bolts.
B. Attach KNEE GUARD to BASE FRAME using 2 – 2 ¾” bolts, 4
– washers and 2 – locknuts. Tighten bolts.

A
. Attach SEAT PAD to SEAT SUPPORT using 2
–
1 ¼” bolts and
2 – washers. Tighten bolts.
B. Attach SEAT SUPPORT to MULTI-LEG MAIN using 1 – 1/2” x
7” bolt and 1 – 1/2” nylock nut. Tighten bolt.

C. Attach BENT LEG CURL HANDLE to holes at top of
BACKPAD SUPPORT TUBES and to top of BACKPAD
using 2-3 ¼” bolts and 2-washers. Do not tighten.
D. Attach lower section of BACKPAD to lower holes of
BACKPAD SUPPORT TUBES using 1-3” bolt and 1-
washer.
E. Tighten bolts from steps C and D at this time.

F. Insert a
Roller Tube through each hole in the Leg
Extension / Leg Curl Arm. Adjust the tubes so that
there are equal lengths protruding from each side of the
arm. Tighten the setscrews.
G. Slide
1- 1” Plastic Washer and 1- Roller Pad onto
each end of the tube.
H. Secure the
Rollers using 1-1” Plastic Washer, 1-
Retainer Plate, and 1- 3/8”x 1” Flat Head Screw on
each shaft end.

A
. Attach 1-SIX SIDED PAD to SEAT STEM using 2-1 ¼” bolts and 2-washers. Tighten
bolts.
B. Attach 1-BACKPAD to BACKPAD FRAME using 2-1” bolts and 2-washers. Tighten
bolts.

A
. Attach 2-LAT HOLD-DOWNS to SEAT FRAME using
2-3” bolts, 4-washers and 2-locknuts. Tighten bolts.
B. Attach 1-9” x 16” PAD to SEAT STEM using 2-1 ¼”
bolts and 2-washers. Tighten bolts.
C. Attach 1-BACKPAD to SEAT FRAME using 1-4” bolt,
1-1 1/4” bolt and 2-washers. Tighten bolts.
D. Slide 2-1” PLASTIC WASHERS and 1-FOAM
ROLLER onto each LAT HOLD-DOWN SHAFT.
E. Secure WASHERS and ROLLERS using 2-
RETAINER PLATES and 2-3/8” Flathead Screws.
Tighten screws.

A
. Attach Barrel End of MULTI-LEG UPPER cable and 1-6" PULLEY to TOP FRAME using
1-3 1/2" bolt, 2-1/2" step spacers, 1-washer and 1-thin nylock nut. Tighten bolt enough to
allow rotation of barrel end of cable.