INFOSEC X2 LCD Touch FR/SCHUKO 500 User manual

User guide __________________________2
Notice d’utilisation __________________15
Gebruikshandleiding_________________30
Bedienungsanleitung ________________43
Guía del usuario ____________________57
Εγχειρίδιο χρήσης ___________________72
87----------------------------------  
500 /700 /1000 /1250 / 1600 / 2000
FR/SCHUKO –IEC –NEMA - UNIVERSAL

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - [email protected] 04 15 AA 59 205 04
2
User guide
To ensure this product is correctly installed and used appropriately, we highly advise you to
read this user guide very carefully.
1. INTRODUCTION
This UPS range is specially designed for multimedia Home Computers and computer
systems in small-sized companies. Its lightweight and compact design is ideal for working
environments where space is limited.
The X2 LCD Touch is Auto-Regulated to provide balanced output power and offer complete
protection for your connected equipment in the event of power cuts or fluctuations. X2 LCD
Touch will keep your connected equipment powered up for several minutes. This will allow
you to close your program(s) and shut the system down correctly. The main features of the
X2 LCD Touch are given below.
2. MAIN CHARACTERISTICS
A highly-reliable microprocessor control
Automatic output voltage regulator (AVR)
Cold start feature if no power supply
Off-mode charging
Automatic restart during AC power recovery
Compact size, light weight
USB communication port
3. SAFETY INSTRUCTIONS
IMPORTANT!
Installing and connecting UPSs in a way that does not comply with accepted practices
releases Infosec Communication from any liability.
Risk of electric shock:
The UPS unit uses potentially hazardous voltages. Do not attempt to disassemble
this equipment as it does not contain accessible components that can be repaired by
users.
All repairs should be performed by qualified technicians only.
The utility power outlet shall be near the equipment and easily accessible. To isolate
the UPS from AC input, remove the plug from the utility power outlet.
The mains outlet that supplies the UPS must be located near the UPS and be easily
accessible.
The UPS has its own internal power supply (battery). There is a risk that output
sockets may still be live after the UPS has been disconnected from the mains power
supply.
Install the UPS in a temperature and humidity-controlled room free of conductive
interference.
It should not be exposed to direct sunlight or sources of heat. Do not cover the
ventilation slots.
Disconnect the UPS from AC power before cleaning with a damp cloth (no cleaning
products).

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - hot[email protected] 04 15 AA 59 205 04
3
     
unit from the AC power supply.
section 10: trouble shooting
call the hot line.
Connected products:
Combined UPS and connected equipment leakage current should not exceed
3,5 mA.
Make sure that the connected load does not exceed UPS capabilities. To ensure
improved backup time and longer battery life, we recommend a load equivalent to 1/3 of
nominal power.
Do not leave any recipients containing liquid on or near the UPS.
Do not plug the UPS input into its own output socket.
Do not plug the UPS into a power strip or surge suppressor.
The UPS has been designed for personal computers. It should not be used with
electrical or electronic equipment with inductive loads such as motors or fluorescent
lights.
Do not connect any household appliances such as microwaves, vacuum cleaners,
hair dryers or life-support systems to the UPS.
Use only CEE 7/7 plugs (FR/SCHUKO models)
Due to excessive consumption, laser printers should not be connected to the UPS.
About batteries:
It is recommended that a qualified technician change the battery.
Do not dispose of the battery in a fire as it may explode.
Do not open or damage the battery! The electrolyte, fundamentally sulphuric acid,
can be toxic and harmful to the skin and eyes. If you come into contact with it, wash
thoroughly with water and clean dirtied clothes.
Do not throw the battery into a fire. It may explode. It has to be disposed of separately
at the end of its useful life. Refer to local legislation and regulations.
The UPS contains one or two large-capacity batteries. To avoid any danger of electric
shock do not open it/them. If a battery needs servicing or has to be replaced, please
contact the distributor.
Servicing should be performed or supervised by competent personnel who take the
necessary precautions. Keep unauthorised personnel away from batteries.
A battery may present a risk of electric shock and cause short circuits. The following
precautions should be taken by the qualified technician:
Remove watches, rings or other metal objects from hands.
Use tools with insulated handles.
Disconnect the charging source prior to connecting or disconnecting battery
terminals.
When replacing batteries, use the same type and number of sealed lead-
acid batteries.
4. STORAGE INSTRUCTIONS
The UPS should be stored with its battery fully charged. In the event of long-term storage,
the batteries should be recharged once every 3 months for 24 hours (by plugging the UPS
             
performance.
Do not keep or use the UPS in any of the following environments:
Any area with combustible gas, corrosive substances or heavy dust.

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - [email protected] 04 15 AA 59 205 04
4
Areas with excessively high or low temperature (above 40°C or below 0°C)
and humidity of more than 90%.
Areas exposed to direct sunlight or near sources of heat.
Areas subject to major vibration.
Outside
In the event of fire in the vicinity, please use dry-powder extinguishers. The use of liquid
extinguishers may present a danger of electric shock.
5. AFTER SALES SERVICE
IMPORTANT!
When calling the After-Sales Department, please have the following information ready, it will
be required regardless of the problem: UPS model, serial number and date of purchase.
Please provide an accurate description of the problem with the following details: type of
equipment powered by the UPS, LED indicator light status, alarm status, installation and
environmental conditions.
You will find the technical information you require in your guarantee or on the identification
plate to the rear of the unit. For your convenience, enter the details in the following box.
Model
Serial number
Date of purchase
X2 LCD Touch …
! Please keep the original packaging. It will be required in the event the UPS is returned to
the After-Sales Department.
CE conformity:
This logo means that this product meets the EMC and LVD standards
(regarding the regulation related to electrical equipment voltage and
electromagnetic fields).
IMPORTANT
Your UPS belongs to the electronic and electrical equipment category. At
the end of its useful life it must be disposed of separately and in an
appropriate manner.
This symbol is also affixed to the batteries supplied with the device, which
means they too have to be taken to the appropriate place at the end of their
useful life.
Contact your local recycling or hazardous waste centre for information on proper disposal of
the used battery.

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - hot[email protected] 04 15 AA 59 205 04
5
6. DESCRIPTION
X2 LCD Touch FR/SCHUKO –IEC –NEMA –UNIVERSAL
500/700/1000/1250/1600/2000
FRONT PANEL
On/Off Switch
Touch LCD

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - [email protected] 04 15 AA 59 205 04
6
REAR PANEL - FR/SCHUKO MODELS
X2 LCD Touch FR/SCHUKO - 500/700/1000 REAR PANEL
X2 LCD Touch FR/SCHUK O –1250 REAR PANEL
X2 LCD Touch FR/SCHUKO –1600/2000 REAR PANEL
USB port
2 protected UPS outlets
(type CEE 7/7)
AC Input Cable
Circuit breaker
USB port
USB port
Circuit breaker
AC Input Cable
4 protected UPS outlets
(type CEE 7/7)
4 protected UPS outlets
(type CEE 7/7)
Circuit
breaker
AC Input Cable

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - hot[email protected] 04 15 AA 59 205 04
7
IEC MODELS
X2 LCD Touch IEC –500/700/1000 REAR PANEL
X2 LCD Touch IEC –1250 REAR PANEL
X2 LCD Touch IEC –1600/2000 REAR PANEL
USB port
3 protected UPS outlets
Fuse
AC Input Outlet
1 surge protected outlet
USB port
Fuse
AC Input Outlet
USB port
3 protected UPS outlets
1 surge protected outlet
4 protected UPS outlets
2 surge protected outlets
Fuse
AC Input Outlet

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - [email protected] 04 15 AA 59 205 04
8
NEMA MODELS
X2 LCD Touch NEMA 500/700/1000 REAR PANEL
X2 LCD Touch NEMA –1250 REAR PANEL
X2 LCD Touch NEMA–1600/2000 REAR PANEL
3 protected UPS outlets
AC Input Cable
Circuit breaker
USB port
USB port
Circuit breaker
AC Input Cable
Fuse
AC Input Cable
USB port
1 surge protected outlet
5 protected UPS outlets
1 surge protected outlet
6 protected UPS outlets
2 surge protected outlets

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - hot[email protected] 04 15 AA 59 205 04
9
UNIVERSAL MODELS
X2 LCD Touch U (Universal outlets) –500/700/1000 REAR PANEL
X2 LCD Touch U –1250 REAR PANEL
X2 LCD Touch U –1600/2000 REAR PANEL
2 protected UPS outlets
AC Input Cable
Circuit breaker
USB port
USB port
Circuit breaker
AC Input Cable
4 protected UPS outlets
4 protected UPS outlets
Fuse
AC Input Cable
USB port

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - [email protected] 04 15 AA 59 205 04
10
OPERATING DISPLAY
7. INSTALLATION AND OPERATION
1. Checking
When you receive your equipment, open the packaging and check that your UPS has not
been damaged. Packaging includes: UPS unit and a user guide
(IEC models : 2 IEC output cables for models 500, 700, 1000 & 1250 VA and 3 IEC output
cables for models 1600 & 2000 VA).
In the event of damage, please submit a standard claim to the after-sales service
department.
UPS
Mode
LCD
Description
UPS
Power on
When UPS is turned
on, it will enter this
mode for 4 seconds.
AC Mode
When AVR is functioning,
icon will flash every
second.
Information will be
displayed in the
following order when
the LCD is touched.
2. Output voltage
3. Input voltage
4. Load level
5. Battery capacity
Overload
in AC
mode
Icon will flash.
When overload occurs,
the alarm will beep
every 0.5 second.
Battery
Mode
When battery level is low,
icon will flash.
The alarm will beep
every 10 seconds and
information will be
displayed in the
following order when
touching the LCD
7. Output voltage
8. Input voltage
9. Load level
10. Battery capacity
Overload
in battery
mode
Icon will flash.
When overload occurs,
the alarm will beep
every 0.5 second.
1
2
3
5
6
9
7
8
10
11
4

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - hot[email protected] 04 15 AA 59 205 04
11
2. Charging the batteries
This unit is shipped from the factory with its internal battery fully charged, however, some
charge may be lost during shipping and the battery should be recharged prior to use. Plug
the unit into an appropriate power supply and allow the UPS to charge fully by leaving it
plugged-in, with no load, for at least 8 hours.
     
position. You may use the UPS immediately, however the back-up power capacity may be
lower than the nominal value required.
3. Placement & storage conditions
The UPS has been designed to operate in a protected environment, at temperatures
between 0°C and 40°C and at a humidity level ranging between 0% and 90% (no
condensation).
Do not obstruct the ventilation slots. Install the unit in an environment which is free from
dust, chemical vapours and conductors. Moreover, in order to avoid any interference, keep
the UPS at least 20cm away from the CPU (central processing unit).
4. Connection
Check the identification plate to the rear of the UPS to make sure that the power supply is
compatible with network voltage and that the device is powerful enough to protect the given
load. Plug the UPS into a 2-pole, earthed outlet (use  original power cable)
or it is recommended to use a 2P+E/CEE22/10A power cable. Then, use cables to connect
computer-related devices to the back of the UPS.
5. On/Off
To turn the UPS unit on, lightly press the power switch. To turn it off, press the power switch
herwise the UPS will
be disabled and your equipment unprotected in the event of power failure.
Note: For maintenance purposes, please turn the UPS on before the PC and other loads,
and turn it off after the connected loads are turned off.
6. DC Start
X2 LCD Touch units are equipped with an integrated DC start function. To start the UPS in
the absence of a power supply and with a full battery, simply press the button.
7. Power Saving Function
If no load is connected to the UPS or if a very small load is connected, the UPS will
automatically shut down after 5 minutes.
8. COMPUTER INTERFACE for X2 LCD Touch
To prevent an abrupt computer system shutdown, connect a USB cable to your computer.
Then you can install and use the automatic shutdown software (Free download from web
site www.infosec-ups.com)
9. BATTERY
The battery is the only UPS component that is not in permanent use. It has a useful life of
approximately 3 to 5 years. However, frequent major discharges or exposure to
temperatures over 20C will shorten its life span. We therefore recommend that users
recharge the battery once every 3 months when the unit is not in use in order to compensate

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - [email protected] 04 15 AA 59 205 04
12
for natural discharging. UPS backup time will depend on the powered load, as well as the
age and condition of the batteries.
WARNING!
Batteries should always be replaced by qualified technicians. Batteries have a very high
short circuit current: connection errors could cause electric arcs resulting in
serious burns.
10. TROUBLE SHOOTING
Should the UPS fail to function correctly we recommend you perform the following tests
before calling the Hot Line.
Check list:

Is the UPS plugged into the mains power supply?
Does the power supply fall within specified unit values?
Is the UPS overloaded?
Is the battery flat or defective?
Fault condition
LCD
Solutions
Output short
circuited
Disconnect short-circuited
loads and restart the UPS
again.
Overload fault
Disconnect all output loads
and restart the UPS again.
Overcharge
Make a service call
immediately.
Bad or severely
discharged
battery
Please replace the battery.
High output
voltage fault
Make a service call
immediately.
Over-temperature
1. Turn off the unit and
wait for it to cool.
2. Or remove excessive
loads and wait for it to
cool.

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - hot[email protected] 04 15 AA 59 205 04
13
11. TECHNICAL SPECIFICATIONS
X2 LCD Touch FR/SCHUKO IEC - UNIVERSAL
X2 LCD
Touch
500
X2 LCD
Touch
700
X2 LCD
Touch
1000
X2 LCD
Touch
1250
X2 LCD
Touch
1600
X2 LCD
Touch
2000
GENERAL CHARACTERISTICS
Technology
Line interactive
Power
500 VA/240W
700 VA/360W
1000 VA/480W
1250 VA/600W
1600 VA/900W
2000 VA/1200W
Power factor
0,5
0,5
0,5
0,5
0,56
0,6
FR/SCHUKO or UNIVERSAL
models : Number of protected
UPS outlets
2
2
2
4
4
4
IEC models : surge protected UPS
outlets / protected UPS outlets
1/3
2/4
PROTECTION & FILTERING
Output form - Protection
Modified sinewave - Discharge / overcharge / overload
FR/SCHUKO models : input
protection
Circuit breaker
IEC models : input protection
Fuse
Universal models : input
protection
Fuse
Circuit breaker
PHYSICAL CHARACTERISTICS
Dimensions - DxWxH (mm)
300 x 101 x 142
320 x 132 x 182
Net weight kg
3,7
4,4
5
8,2
10,4
11
INPUT TECHNICAL CHARACTERISTICS
Voltage
220/230/240 V
Voltage range - Frequency
162-290 VAC - 50/60 Hz (auto sensing)
OUPUT TECHNICAL CHARACTERISTICS (battery mode)
Voltage
220/230/240 V
Automatice voltage regulation
± 10 %
Frequency
50 ou 60 Hz ± 1 Hz (auto sensing)
Crest ratio
03:01
Output current (A)
2
3
3,9
4,5
6,8
9,1
BATTERY
Battery charger
Operates when the UPS is connected to mains
Cold start (no mains)
Yes
Batteries type & number
12V/4,5AH*1
12V/7AH*1
12V/9AH*1
12V/7AH*2
12V/9AH*2
12V/9AH*2
Recharging voltage
13.7s Vdc
27.4 Vdc
Recharging time
4 to 6 hours to 90 % after complete discharge
Backup time
6-40 min. depending on connected load
INDICATORS
Touch LCD
Touch LCD : Input voltage, output voltage, battery capacity, load level and UPS status
AUDIBLE ALARMS
Battery mode
Sounding every 10 seconds
Low battery
Sounding every second
Overload
Sounding twice every second
Battery replacement
Sounding every 2 seconds
Default
Continuously sounding
COMMUNICATION
Communication port
USB
ENVIRONMENT
Ideal environment
0-40°C, 0-90% of relative humidity (without condensation)
Noise level
<40dB
NORMS (FR/SCHUKO / IEC models)
Standard
CE RoHS
EMC (Electromagnetic
compatibility)
EN62040-2:2006, EN61000-4-2:2009, EN61000-4-3:2006+A1:2008+A2:2010,
EN61000-4-4:2004+A1:2010, EN61000-4-5:2006, EN61000-2-2:2002
Low voltage (Safety)
EN60950-1:2006+A11:2009+A1:2010, EN62040-1:2008
SALES INFO
Warranty
2 years
Gencods –FR/SCHUKO models
3700085
65998 4
3700085
65999 1
3700085
66000 3
3700085
66001 0
3700085
66002 7
3700085
66003 4
Gencods –IEC models
3700085
66036 2
3700085
66037 9
3700085
66038 6
3700085
66039 3
3700085
66040 9
3700085
66041 6
Gencods –UNIVERSAL models
3700085
66004 1
3700085
66005 8
3700085
66006 5
3700085
66007 2
3700085
66008 9
3700085
66009 6

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - [email protected] 04 15 AA 59 205 04
14
X2 LCD Touch NEMA
X2 LCD
Touch
500
X2 LCD
Touch
700
X2 LCD
Touch
1000
X2 LCD
Touch
1250
X2 LCD
Touch
1600
X2 LCD
Touch
2000
GENERAL CHARACTERISTICS
Technology
Line Interactive with AVR
Power
500 VA
700 VA
1000 VA
1250 VA
1600 VA
2000 VA
240 W
360 W
480 W
600 W
900 W
1200 W
Power factor
0,5
0,5
0,5
0,5
0,56
0,6
Number of surge protected
outlet/protected UPS outlets
1/3
1/5
2/6
PROTECTION & FILTERING
Output form
Modified sinewave
Protection
Discharge / overcharge / overload
Input protection
Fuse
Circuit breakers
PHYSICAL CHARACTERISTICS
Dimensions - DxWxH (mm)
300 x 101 x 142
320 x 132 x 182
Net weight kg
3,7
4,4
5
8,2
10,4
11
INPUT TECHNICAL CHARACTERISTICS
Voltage
[110/120] or [220/230/240 VAC]*
Voltage range
[81-145 VAC] or [162-290 VAC]*
Frequency
50/60 Hz (auto sensing)
Input current-Low / High voltage
(A)s
4.1 or 2.0
5.9 or 3.0
7.7 or 3.9
9.1 or 4.5
13.6 or 6.8
18.2 or 9.1
OUPUT TECHNICAL CHARACTERISTICS (AC)
Voltage
[110/120] or [220/230/240 VAC]*
Automatice voltage regulation
[81-145 VAC] or [162-290 VAC]*
Input current-Low / High voltage
(A)
4.1 or 2.0
5.9 or 3.0
7.7 or 3.9
9.1 or 4.5
13.6 or 6.8
18.2 or 9.1
OUPUT TECHNICAL CHARACTERISTICS (battery mode)
Voltage
110/120 or 220/230/240 VAC
Automatice voltage regulation
± 10 %
Frequency
50 ou 60 Hz ± 1 Hz
Crest ratio
03:01
Output current (A)
4,1
5,9
7,7
9,1
13,6
18,2
BATTERY
Battery charger
Operates when the UPS is connected to mains
Cold start (no mains)
Yes
Batteries type & number
12V/4,5AH*1
12V/7AH*1
12V/9AH*1
12V/7AH*2
12V/9AH*2
12V/9AH*2
Recharging voltage
13.7 Vdc
27.4 Vdc
Recharging time
4 to 6 hours to 90% after complete
discharge
6 to 8 hours to 90% after complete
discharge
Backup time
6 - 20 min. depending on connected load
INDICATORS
Touch LCD
Touch LCD : Input voltage, output voltage, battery capacity, load level and UPS status
AUDIBLE ALARMS
Battery mode
Sounding every 10 seconds
Low battery
Sounding every second
Overload
Sounding twice every second
Battery replacement
Sounding every 2 seconds
Default
Continuously sounding
COMMUNICATION
Communication port
USB
ENVIRONMENT
Ideal environment
0-40°C, 0-90% of relative humidity (without condensation)
Noise level
<40dB
NORMS (HV models)
Standard
CE
EMC (Electromagnetic
compatibility)
EN62040-2:2006, EN61000-4-2:2009, EN61000-4-3:2006+A1:2008+A2:2010,
EN61000-4-4:2004+A1:2010, EN61000-4-5:2006, EN61000-2-2:2002
Low voltage (Safety)
EN60950-1:2006+A11:2009+A1:2010, EN62040-1:2008

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - hot[email protected] 04 15 AA 59 205 04
15
SALES INFO
Warranty
2 years
Gencods (LV 110V)
3700085
68120 6s
3700085
68121 3
3700085
68122 0
3700085
68123 7
3700085
68124 4
3700085
68125 1
Gencods (HV 230V)
3700085
68126 8
3700085
68127 5
3700085
68128 2
3700085
68129 9
3700085
68130 5
3700085
68131 2
*Low voltage (110V) and High voltage (230V) are different products.

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - [email protected] 04 15 AA 59 205 04
16
Notice d’utilisation
ecte et une utilisation appropriée de ce produit, nous vous
conseillons de lire attentivement cette notice.
1. INTRODUCTION
           
informatique personnelle. Son faible poids ainsi que son design compact permettent de

X2 LCD Touch fournit un courant de sortie stabilisé grâce à son Auto Régulation et offre
ainsi une protection complète à vos équipements connectés aussi bien en cas de variation
du courant que de coupure ou microcoupure.
En cas     X2 LCD Touch    
équipement connecté pendant plusieurs minutes vous permettant ainsi de sauvegarder vos
données, de sortir du programme et de fermer correctement votre système informatique.
Les principales fonctions de X2 LCD Touch sont détaillées ci-après.
2. CARATERISTIQUES PRINCIPALES
Contrôlé par microprocesseur pour garantir une haute fiabilité
matique de tension)
Démarrage à froid

Redémarrage automatique au retour secteur
Faible encombrement, faible poids
Port USB
3. INSTRUCTIONS DE SECURITE
IMPORTANT !
Installer et connecter les onduleurs de façon non-conforme aux rè  
désengage Infosec Communication de toute responsabilité
Risque de choc électrique :
D
appareil. Celui-ci ne contient pas de composants accessibles pour son dépannage par

Toutes les opérations de maintenance doivent être effectuées par un personnel
qualifié.
-ci doit être facilement
accessible. Pour      


 le courant du secteur.

 Ne
pas couvrir les grilles de ventilation.
    e pas utiliser de détergent liquide ou
aérosol. Utiliser uniquement un chiffon légèrement humide.

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - hot[email protected] 04 15 AA 59 205 04
17

 afin de désactiver complètement l
     se référer à la section 10: «Dépannage» puis
contactez le Service Après-Vente.
Produits connectés:

excéder 3,5 mA.


nous recommandons une charge égale au 1/3 de la puissance nominale des prises.
Ne pas laisser de 


    as adapter pour
alimenter des équipements électroniques avec des charges inductives telles que des
moteurs ou des lampes fluorescentes, ni des charges résistives.

ntretien artificiel pour la vie, four micro-onde, aspirateur, sèche-
Utiliser seulement CEE 7/7 plugs (modèles FR/SCHUKO)
          
imprimante laser.
A propos des batteries:
Il est recommandé de faire appel à un personnel qualifié pour remplacer la batterie.
Ne pas exposer la batterie à une source inflammable, celle-
Ne pas ouvrir ni abîmer la batterie ! 
être toxique et nocif pour la peau et les yeux. En cas de contact laver abondamment à
l'eau et tout vêtement souillé.
   
collecte sélective et ne pas être jetée avec les ordures ménagères. Se reporter à la
législation et aux règlements locaux.
 contient une/deux batteries de grande capacité. Il est donc conseillé de ne
pas ouvrir ce compartiment pour éviter tout risque de choc électrique. Si une révision ou
un remplacement de la batterie est nécessaire, merci de contacter directement le
distributeur.
La révision des batteries doit être effectuée par un personnel qualifié ayant une
parfaite connaissance des précautions de sécurité.
Une batterie peut causer un choc électrique ou un intense court-circuit. Les


Utiliser des outils à poignées isolées.

Pour remplacer les batteries, utiliser le même nombre et le même type de
batterie.
4. INSTRUCTIONS DE STOCKAGE
-utilisation
prolongée, devraient être rechargées tous les 3 mois (simplement
en branchant 

les recommandations suivantes :

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - [email protected] 04 15 AA 59 205 04
18
t doit être ventilé et exempt de poussière, de vapeurs chimiques et
de contaminants conducteurs.
La température de stockage doit impérativement être inférieure à 40°C et
supérieure à 0°C.

Eviter toute exposition directe aux rayonnements solaires ou à toute autre
source de chaleur.


choc électrique.
5. SERVICE APRES-VENTE
IMPORTANT !
            
informations suivantes qui vous seront dans tous les cas demandées : le modèle de

       : état des voyants, état de

Ces renseignements sont notés sur le bon de garantie ou inscrits sur la plaque signalétique
-dessous.
Modèle
Numéro de série
Date d’achat
X2 LCD Touch …
! 
votre onduleur en nos locaux.
Conformité CE :
Ce logo signifie que ce produit est conforme aux exigences imposées par
les directives LVD et EMC (relatives aux réglementations associées à la
sécurité basse tension et à la compatibilité électromagnétique).
IMPORTANT
Les onduleurs appartiennent à la catégorie des équipements électriques et

sélective et ne pas être jetés avec les ordures ménagères.
Ce symbole est aussi apposé sur les batteries fournies avec cet appareil, ce
           
approprié.
Prenez contact avec le système de recyclage ou centre de déchets dangereux local pour
cyclage de la batterie usagée.

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - hot[email protected] 04 15 AA 59 205 04
19
6. DESCRIPTION
FACE AVANT DU X2 LCD Touch EX/IEC/NEMA/U
Bouton marche/arrêt
Ecran LCD Touch

INFOSEC UPS SYSTEM - 4, rue de la Rigotière - 44700 Orvault - FRANCE - www.infosec-ups.com
Hot Line Tel + 33 (0)2 40 76 15 82 - Fax + 33 (0)2 40 94 29 51 - [email protected] 04 15 AA 59 205 04
20
FACE ARRIERE –MODELES FR/SCHUKO
X2 LCD Touch EX 500/700/1000 FACE ARRIERE
X2 LCD Touch EX –1250 FACE ARRIERE
X2 LCD Touch EX –1600/2000 FACE ARRIERE
Port de communication
USB
2 prises de sorties
secourues (type CEE 7/7)

intégré
Disjoncteur
Port de communication
USB
Port de
communication USB
Disjoncteur

intégré
4 prises de sortie
secourues (type CEE 7/7)
4 prises de sorties
secourues (type CEE 7/7)
Disjoncteur

intégré