Innova 10 HP DC User manual

ehpocaGEO
2.0
8 - 10 On-Off
10 - 12 DC Inverter
12 DC Inverter ELEC
User manual EN

2
Innova S.r.l
This booklet, code N273027C - Rev. 00 - (01/17) consists
of 20 pages.
Compliance
We would first of all like to thank you for having chosen one of our products.
We are sure you will be happy with it because it represents the state of the art in the technology of
home air conditioning.
By following the suggestions contained in this manual, the product you have purchased will operate
without problems, giving you optimum room temperatures with minimum energy costs.
The pictograms in the next chapter provide the necessary
information for correct, safe use of the appliance in a rapid,
unmistakable way.
Symbols
U
User
- Refers to pages containing instructions or information
for the user.
I
Installer
- Refers to pages containing instructions or information
for the installer.
S
Service
- Refers to pages containing instructions or information
for the CUSTOMER TECHNICAL ASSISTANCE
SERVICE installer.
Editorial pictograms
Safety pictograms
Warning
- It indicates actions that require caution and a suitable
preparation.
Prohibition
- Refers to prohibited actions.
This unit complies with the following European Directives:
• Low voltage 2014/35/EU
• Electro-magnetic compatibility 2014/30/EU
• Use restrictions of hazardous substances in electrical
and electronic equipment 2011/65/EC (RoHS2)
• Waste electrical and electronic equipment 2012/19/
EC (WEEE).
• Energy consumption indication on the labels of energy-
related products 2010/30/EU
• ErP Directive 2009/125/EC and regulation 2012/20EC

3
S
I
U
EN
USER MANUAL
1 User manual
1.1 Warnings ........................................................... 4
1.2 Management of the appliance with the touch-screen display and remote control....... 4
1.3 Description of operations ............................................... 5
1.4 Setting cool only or heat only modes ....................................... 8
1.5 Brightness regulation .................................................. 8
1.6 Touch-screen display key lock ........................................... 8
1.7 Hotel function ........................................................ 8
1.8 Heating operating (only for ELEC model) .................................... 8
1.9 Suggestions for power saving ............................................ 9
1.10 Diagnosis of problems ................................................. 9
1.11 Technical specifications ................................................ 11
1.12 Periodic Maintenance .................................................. 12
2 INNOVA App operation
2.1 Minimum system requirements ........................................... 13
2.2 Installing and using the APP ............................................. 13
General table of contents

4
S
I
U
1.1
1.2
USER MANUAL
USER MANUAL
Warnings
Managing the appliance with the touch-screen display and the remote control
Objects or structural obstacles (furniture, curtains,
plants, leaves, blinds, etc.) must not obstruct the normal
air flow both from the internal and from the external grids.
It is strictly forbidden to place any containers on top
of the appliance, especially if they contain liquid. This
could trigger a short-circuit, damage the appliance and/
or expose the user to the risk of electrocution.
Do not lean against, or worse sit on, the body of the
conditioner, this would damage the appliance.
Do not move the horizontal air outlet flap manually. Always
use the remote control to perform such operation.
In the event of water leaks, turn off the appliance and
disconnect the electric power supply. Call the nearest
service centre.
During heating mode, the conditioner eliminates
periodically any ice formed on the external battery. In
such situation, the machine keeps on working, but it
does not dispense warm air to the room. This phase
can last from 3 up to maximum 10 minutes.
The appliance must not be installed in rooms where
explosive gases develop or where there are humidity
and temperature conditions that exceed the maximum
levels reported on the installation manual.
Clean the air filter regularly as described in the specific
paragraph.
Normally, the display shows the operating status (see
paragraph entitled Description of operations), as well as
any alarms (see paragraph entitled Display alarms).
In addition, it is possible to select the various functions by
pressing the symbols.
1Corresponding button on remote control
2Corresponding button on touch-screen display
BUTTON / DISPLAY:
Setpoint Heating only button (2)
Up button Nocturnal well-being button
Down button Control of air flow direction button
On/off button Fan speed control button
Well-being button
(economic automatic mode) Timer mode setting button (1)
Cooling only mode button Timer mode setting button (2)
Dehumidification only mode button Brightness sensor
Ventilation only mode button Digital thermometer;
1÷7 red bars in winter, blue bars in summer
Heating only button (1) Not used

5
S
I
U
1.3
EN
USER MANUAL
Description of operations
It is possible to select the various modes by pressing the
buttons (see paragraph entitled Description of operations).
The remote control provided has been designed to
be functional and hard-wearing, however, it must be
handled cautiously.
Avoid:
- leaving it exposed to rain, pouring liquids on it or
dropping it into water
- hitting it or dropping it on hard surfaces
- leaving it under the sun
- placing obstacles between the remote and the
appliance while using it.
In addition:
- if there are other appliances using remote controls in
the room (TV, radios, stereos, etc.), interferences may
occur
- electronic or fluorescent lamps can interfere with
communication between the remote and the appliance
- remove the battery if not using the remote for a long
time.
Only CR2012 3V dry lithium batteries must be used
(supplied). Used batteries must be handed over to
the specific collection areas as arranged by the Local
Authorities for this type of waste.
In order to insert the batteries, open the specific cover
in the bottom part of the remote. The battery must be
inserted respecting polarity. Once the battery is inserted,
close the cover.
In order to manage the appliance using the remote control
and the touch-screen, the main switch on the electrical
power supply line must be turned on (its exact position can
be indicated by the technician who installed the appliance)
or the power supply plug must be connected to the system
socket.
Once such operations have been performed, it is possible
to manage the system by holding down the symbols on the
touch-screen (for 3 seconds) or by using the remote control.
In order to send commands to the internal unit, the top part
of the remote must point towards the display of the internal
unit. The reception of the command is confirmed by a beep
and by the display. The maximum distance for the remote
control to work is approximately 8 metres.
General start-up and management
Battery insertion
Key/Display Operation
The keys of the remote control and of the touch screen display perform the same functions.
When the unit is turned on, the 3 digits on the display will show the set-point.
• It is possible to set the set-point between 16 and 31°C, to which temperature the unit will bring the room.
If the temperature is set too low or too high, not only it is unhealthy, but it is also an unnecessary
waste of energy.

6
S
I
U
USER MANUAL
Key/Display Operation
Switching the appliance on and off
It is possible to switch the appliance on or off (stand-by) by pressing the specific button. The control system of the
appliance is equipped with a memory, so settings will not be lost if the appliance is switched off or in the power supply
is cut. This key is used to activate or deactivate the appliance for short periods of time.
In case of long periods of inactivity, the appliance must be deactivated by disconnecting either the main switch or
the plug from the socket.
Well-being button (economic automatic mode)
By choosing this mode on the appliance, it sets the best level of comfort in the room. The conditioner selects the mode
automatically (cooling or heating) according to the temperature set and ventilation speed according to the temperature
of the room.
Cooling only mode
• In this mode, the appliance dehumidifies and cools the room.
• It is possible to set the desired temperature between 16 and 31°C and, if this temperature is lower than the room
temperature, the compressor starts up after three minutes (maximum) and the appliance starts dispensing cool
air, maintaining ventilation active even if the setpoint has been reached.
Dehumidification only mode
In this mode, the appliance dehumidifies the room. Selecting this mode is useful during mid-seasons, i.e. on days (e.g.
rainy ones) when the temperature is pleasant, but excess humidity causes discomfort. This mode ignores both room
temperature and ventilation speed settings.The latter is always set to a minimum. It is normal for the appliance to work
intermittently.
Ventilation only mode
By selecting this function, the compressor is never activated and the appliance does not affect either room temperature
or humidity. IT IS possible to choose the speed of the fan
Heating only mode
• In this mode, the appliance heats the room.
Set on heating only mode, the appliance periodically defrosts the evaporator coil, if necessary. During this phase,
the conditioner does not dispense warm air, even if its internal components are on, except for the room fan.
• It is possible to set the desired temperature between 16 and 31°C and, if such temperature is higher than the
room temperature, the compressor starts up after three minutes (maximum) and the appliance starts dispensing
warm air.
Nocturnal well-being button
While the appliance is on in the selected cooling or heating mode, it is possible to choose different functions by
pressing the button in order to maximise noise reduction, energy saving and nocturnal well-being regulation.
In this mode, ventilation is set on minimum speed.
This mode should be activated right before going to sleep.
• In cooling mode, the set temperature is increased by 1°C after one hour and by another degree after two. After
the second hour, the temperature is no longer changed and, after six hours, the appliance is put in stand-by.
• In heating mode, the set temperature is lowered by 1°C after one hour and by another degree after two. After the
second hour, the temperature is no longer changed and, after six hours, the appliance is put in stand-by.
This function is not available for dehumidification only, ventilation only and economic automatic modes and can be
excluded any time (ideally once awake) by pressing the button again.
If the Timer has also been set, the appliance will turn off at the set time.
Control of air flow direction
By pressing the specific button, it is possible to either select the continuous oscillation of the mobile air outlet flap - in
such case, the symbol on the display is lit - or to block it in any position.
IMPORTANT: The mobile flap must never be moved manually. In cooling and dehumidification modes, the position
of the flap is reset every 30 minutes to prevent dew from forming.

7
S
I
U
EN
USER MANUAL
Key/Display Operation
Fan speed control (models 8 and 10)
By pressing this button several times, the speed will change according to the following sequence: Minimum, Medium,
Maximum and Automatic
The higher the speed is set, the better the appliance will perform, but it will be less quiet. By selecting Automatic mode
(shown by three speed bars moving up and down on the display), the on-board microprocessor automatically adjusts
the speed, so that it stays higher the greater the difference between the temperature detected and the temperature
set. The speed will always be automatically decreased as the room temperature approaches the set temperature.
This is not possible in humidification only or nocturnal well-being mode where the appliance can only operate at a low
speed.
Setting power for models inverter 10HP and 12HP
By pressing this key sequentially, it is possible to set the power supplied by the appliance on 5 adjustments: Minimum,
Medium, Maximum, Dual Power and Automatic.
The higher the power is set, the better the appliance will perform, but it will be less quiet.
The Dual Power function (shown by three flashing speed bars on the display and the seven red or blue bars moving
up and down of the digital thermometer), available only in heating and cooling mode, supplies a 30-minute Overboost.
Then, the controller inhibits the function and switches to automatic mode.
By selecting Automatic mode (shown by three speed bars moving up and down on the display), the on-board
microprocessor automatically adjusts the speed, so that it stays higher the greater the difference between the temperature
detected and the temperature set. This is not possible in humidification only or nocturnal well-being mode where the
appliance can only operate at a low speed.
Setting the Timer function
• The appliance allows the user to program when to turn it on and off, as required.
• While the conditioner is running, it is possible to schedule when it turns off by pressing the Timer button, followed
by the number of hours (from 1 to 24), after which the unit will be put in stand-by.
• When the air conditioning unit is off, it is possible to schedule when it turns on by pressing the Timer button,
followed by the number of hours (from 1 to 24) after which the unit will start.
• Then, press the confirm button.
Touch-screen display key lock
• The key lock is activated by keeping the Timer symbol on the touch-screen display pressed for three seconds.
The user cannot perform any actions. The stand-by symbol flashes every second.
• To deactivate the lock, keep the Timer symbol on the touch screen pressed for three seconds once again.
The lock remains active in the case of a power failure and also if the remote control is used!

8
S
I
U
USER MANUAL
1.4
1.5
1.6
1.7
The key lock is activated by keeping the Timer symbol on
the touch-screen display pressed for three seconds.
The user cannot perform any actions.
The stand-by symbol flashes every second.
To deactivate the lock, keep the Timer symbol on the touch
screen pressed for three seconds once again.
The lock remains active also for the next operations performed
via remote control and in the event of a power failure.
Press and hold the air exchange key ( ) for 10 seconds
to enable the function ("En" displayed); the dehumidification
and Auto functions are disabled (leaving active only
ventilation, heating and cooling) and the settable set range
is reduced from 22 to 28 in cooling mode and from 16 to
24 in heating mode).
The display brightness sensor can be disabled (leaving the
maximum brightness at all times) by pressing and holding the night button ( ) for 10 seconds. "ds" (disabled) or
"En" (enabled) will appear on the display.
Touch-screen display key lock
Hotel function
It is possible to deactivate the heating or the cooling
modes following a simple procedure.
Keep the A key on the touch-screen display pressed for
5 seconds until HC (heating and cooling) appears on the
display.
Press the A key for 1 second to switch to the CO (cooling
only) mode.
Press the A key again to switch back to HO (heating only)
mode.
Wait for 3 seconds without touching anything to memorise
the setting and return to normal operations.
Setting cool only or heat only modes
Brightness regulation
1.8
The 12HP DC inverter ELEC has an additional electric
element which provides heat when the weather conditions
outside are bad. The heat power of the resistor is equal
to 1,000W, so when the device software switches the
2.0 unit on, it will provide the combined thermal power
produced by the heat pump and the thermal power of the
electric element.
If you need to operate the appliance in quiet mode, it can
be activated with “element only”, without the compressor,
simply by setting the night-time mode by pressing the
button
In this case, the element comes on if:
• the 2.0 unit is working with the heat pump (heating
mode);
• the room temperature (measured by the internal probe)
is one degree less than the configured setpoint;
• the room temperature is ≤ 27 °C;
• there are no alarms or failures related to the ventilation,
room temperature probe and temperature coil.
The ventilation speed in this mode is fixed at 700 rpm.
If night-time operation is not selected, the element will
switch on, together with the compressor, if:
• the 2.0 unit is working with the heat pump (heating
mode);
• the room temperature is ≤ 24 °C;
• the room temperature is 2°C lower than the setpoint<
• the internal coil temperature is ≤ 44 °C;
• the ventilation is switched on and stable;
• there are no alarms or failures related to the ventilation,
room temperature probe and temperature coil.
In normal operation, with the heating switched on, the
element will deactivate if:
• the coil temperature of the internal exchanger is ≤ 47 °C;
• the room temperature is greater than the setpoint;
• the room temperature is at 25 °C;
• the ventilation stops or the fan is faulty;
• the compressor discharge temperature increases
abnormally;
• the compressor operating frequency increases
abnormally;
Heating operation (only for ELEC model)

9
S
I
U
1.9
1.10
EN
USER MANUAL
Suggestions for power saving
Diagnosis of problems
- Always keep the filters clean (see maintenance and
cleaning chapter).
- Keep the doors and windows of the rooms to be air
conditioned closed
Do not let direct sunlight to enter the room (use
curtains or lower the blinds or close the shutters)
- Do not block the air flow paths (input and output)
of the unit; this, as well as causing a non-optimal
performance of the unit, will jeopardise the correct
operation of the same and may cause irreparable
damage to the units.
For the User it is very important to distinguish any
inconveniences or abnormal operation of the unit
compared to its normal operation. Also, the most
common problems can be easily solved by means of
simple operations performed by the User (See paragraph:
Troubleshooting), while for some alarms signalled on the
display, it is necessary to contact Customer Service.
We also remind you that any attempt to repair the unit on part
of unauthorised technicians will void the warranty immediately.
- The compressor will not restart before a certain time has
passed (about three minutes from the previous stop). It is
not possible to stop and restart the compressor without
waiting at least three minutes. This is provided for in the
operating logic of the unit, so as to protect the compressor
from frequent activations.
- During operation in heating mode, the warm air is delivered
a few minutes after the activation of the compressor. If the
fan started at the same time as the compressor, in the first
minutes of operation the air delivered would be too cold
(which may disturb the occupants of the room) since the
unit is not yet ready.
If the remote control has been lost, the batteries are exhausted or it
no longer works, the unit can be operated by using the keys on the
touch screen display on the machine.
Operating aspects that should not be interpreted as problems
Using the unit if the remote control is not available
Should any anomaly occur in the condensation water
system, the maximum level float blocks the conditioner
and the OF code appears on the display.
During cooling and dehumidification, electronics keeps the
water distribution system active with the battery - together
with the fan - to disperse excess water in the container.
If the problem persists, please contact the assistance
service.
During heating, condensation should drain freely through
the specific pipe. In the event of an alarm, check that
the condensation pipe is not bent or obstructed, thus
preventing the water from flowing out.
Evacuation of condensate water in the event of an emergency
If the presence contact is not closed, the appliance will
not start and the CPalarm appears on the display.
Open CP contact

10
S
I
U
USER MANUAL
In the even of a malfunction, please refer to the following table. If,
after performing the suggested checks, the problem is not solved,
please contact the authorised technical assistance.
An alarm code appears on the display in the event of
faults. Some of the functions, however, remain active (see
FUNCTIONING column).
The only way to solve the problem is to disconnect and reconnect
the appliance. If the alarm still appears, please contact the
authorised technical assistance.
Troubleshooting
Display alarms
Fault Possible causes Solution
The appliance
doesn't switch
on
No power supply
Check there is power supply (by turning a light on, for example).
Check that the thermal-magnetic circuit breaker used exclusively to protect
the appliance has not been tripped (if it has, reset it). If the problem repeats
immediately, please call the Service Centre and avoid trying to make the
appliance work.
Remote control batteries have run out Check that the appliance can be turned on using the touch-screen display and
substitute the batteries.
The appliance
does not cool/
heat adequately.
The temperature set is too high or too
low. Check and adjust the temperature, if necessary.
The air filter is clogged Check the air filter and clean it if necessary
Check that there are no other obstacles
to the air flow both inside and outside. Remove anything that might block the air flow.
The heating and cooling load has
increased (for example, a door or
a window has been left open or an
appliance has been installed in the
room which generates a lot of heat).
Try to reduce the heating and cooling load of the room following instructions
below:
• Cover large windows exposed to sunlight with curtains or with external
maskings (blinds, porches, reflecting films, etc.);
• The air conditioned room must remain closed for as long as possible;
• Avoid turning on halogen lamps or other high energy consumption
appliances such as small ovens, steam irons, hot plates etc.).
Alarm Cause Operation
E1
Faulty room temperature RT sensor It is still possible to activate Cooling, Dehumidification and Heating modes. It only monitors
the antifreeze function of the internal coil.
E2
Faulty internal coil IPT sensor It is still possible to activate Cooling, Dehumidification and Heating modes.
E3
Faulty outside temperature OT sensor It is still possible to activate Cooling, Dehumidification and Heating modes.
E4
Faulty external coil OPT sensor It is still possible to activate Cooling, Dehumidification and Heating modes. Defrosting is
performed at fixed times.
E5
Faulty internal fan motor None of the modes can be activated.
E6
Faulty external fan motor None of the modes can be activated.
E7
Lack of communication with the
display * None of the modes can be activated.
E8
Compressor discharge probe failure None of the modes can be activated.
CP
Open CP contact The appliance only works if the contact is closed. Check that the clamps are connected.
OF
Maximum level float intervention
During cooling and dehumidification, electronics switches the compressor off and keeps
the water distribution system active with the battery - together with the fan - to disperse
excess water. During heating, condensation should drain freely through the specific pipe.
In the event of an alarm, check that the condensation pipe is not bent or obstructed, thus
preventing the water from flowing out.
* for models 10 and 12 HP DC Inverter: lack of communication
between the main, power, driver or display boards

11
S
I
U
1.11
(1) DB 27°C - WB 19°C DB 35°C - WB 24°C
(2) DB 20°C - WB 15°C DB 7°C - WB 6°C
(3) DB 20°C - WB 15°C DB -7°C - WB -8°C
(4)
(5)
DB 35°C - WB 24°C DB 43°C - WB 32°C
DB 18°C DB -5°C
DB 27°C DB 24°C - WB 18°C
DB 5°C DB -10°C
EN
USER MANUAL
Technical specifications
Please read data plate to obtain the technical data listed
below.
- Power supply voltage
- Maximum absorbed power
- Maximum absorbed current
- Amount of refrigerant gas
- Casing protection level
*with Dual Power function activated during heating
Ambient T External T
Cooling mode tests (EN 14511)
Heating mode tests (EN 14511)
Heating mode tests
Internal side sound pressure measured in semi-anechoic chamber at a distance of 2 m.
Internal side sound pressure measured in accordance with regulation EN 12012
Internal ambient temp. External ambient temp.
Maximum operating temperature in cooling mode
Minimum operating temperature in cooling mode
Maximum operating temperatures in heating mode
Minimum operating temperatures in heating mode
Operating limits
Reference conditions
U.M. 8 HP 10 HP 10 HP DC
Inverter
12 HP DC
Inverter
12 HP DC
Inverter
ELEC
Technical specifications
Cooling power (1) kW 1.65 2.30 2.04 2.35 2.35
Power in max cooling mod. Dual Power kW / / 2.60 3.10 3.10
Heating power (2) kW 1.70 2.25 2.10 2.36 2.36
Heating power (3) kW 0.79 1.05 0.98 1.11 1.11
Additional power electrical element kW / / / / 1.00
Power in max heating mod. Dual Power kW / / 2.64 3.05 3.05
Power absorbed when cooling (1) W 580 850 630 730 730
Power absorbed when heating (2) W 545 725 638 720 720
Dehumidification capacity L/h 0.8 1.1 1.0 1.1 1.1
Power supply voltage V-F-Hz 230-1-50 230-1-50 230-1-50 230-1-50 230-1-50
EER W/W 2.84 2.71 3.24 3.22 3.22
COP W/W 3.12 3.1 3.29 3.28 3.28
Energy efficiency class when cooling A A A+ A+ A+
Energy efficiency class when heating A A A A A
Internal-external ventilation speed No. 3 3 3 3 3
Internal/external air flow at max speed m³/h 360/430 400/480 380/460 400/480 400/480
Internal/external air flow at medium speed m³/h 300/360 320/390 310/380 320/390 320/390
Internal/external air flow at min speed m³/h 240/320 270/340 260/330 270/340 270/340
Dimensions (WxHxD) mm
1030x555x170 1030x555x170 1030x555x170 1030x555x170 1030x555x170
Weight including packaging kg 47.6 48.0 48.5 48.5 48.5
Sound pressure level (min-max) (4) dB(A) 29/38 32/41 26/39 27/41 27/41
Unit sound power level inside (min-max) (5) dB(A) 44/57 45/58 44/57 45/58 45/58
Wall holes diameter mm 162 162 162 162 162
Wall holes distance mm 293 293 293 293 293
Refrigerant gas R410A R410A R410A R410A R410A
Qty. R410A refrigerant gas g 480 520 560 560 560
Global warming potential (GWP 2088) kgCO
2
eq. 1,002 1,086 1,169 1,169 1,169
Maximum absorbed power W 690 920 950* 1,060* 2,060*
Maximum absorbed current A 3 4.1 4.4* 4.8* 4.8*
Maximum working pressure PS MPa 3.8 3.8 3.8 3.8 3.8
Degree of protection IPX0 IPX0 IPX0 IPX0 IPX0

12
S
I
U
1.12
1
2
3
USER MANUAL
Disconnect the unit from the power supply before
each cleaning and maintenance intervention by
setting the main power supply switch to off.
Wait for the components to cool down in order to
avoid any burns.
Do not use abrasive sponges or abrasive or corrosive
detergents as you might damage the painted surfaces.
When necessary, clean the external surfaces with a soft
damp cloth.
The air conditioner you have bought has been designed to
keep maintenance operations to a minimum, in fact, they
only include the following cleaning operations:
- Clean the air filter after a period of continuous use
and according to the concentration of impurities in the
air, or when you wish to start-up the appliance after a
period of inactivity.
The filter is located in the top part of the appliance.
To extract the filters:
- open the grid and remove it;
- extract the filters by lifting them;
- remove the dust from the filter with a vacuum cleaner
or by washing it in running water without using
detergents or solvents and leave to dry;
- put the filters back on top of the batteries, taking care
to position them correctly;
- put the grid back.
After filter cleaning check if the panel is properly
mounted.
It is forbidden to use the device without its mesh filter.
The air conditioner you have bought has been designed to
keep maintenance operations to a minimum, in fact, they
only include the following cleaning operations:
Periodic Maintenance
Cleaning the filters
External cleaning

13
S
I
U
2.1
EN
USER MANUAL
INNOVA APP OPERATION
Minimum system requirements
1. The download and installation of the App depends on
some system requirements of your smartphone.
2. For Android smartphones, the minimum version is
4.1.1
3. For Apple smartphones, the operating system must
be IOS 8.0 or higher.
Figure 2-1
Press the button as shown in the figure to start
the automatic procedure for the recognition and
WIFI connection on the Innova 2.0 network. (only
on Android devices).
If the automatic procedure does not start, it can
be configured manually as indicated below.
On the first screen it is possible to select the
language preference and the way the push
notifications are handled.
If you check the notification box, the alarms will
appear on your smartphone.
Figure 2-2
2.2 Installing and using the APP
1. From the application menu on your smartphone, find
and open the "play store" icon.
2. Once you have logged into the store, search for
InnovApp DuePuntoZero
3. Once you have found InnovApp 2.0, download the
App and install it following the wizard.
4. Open the App. Once open, the screen in Figura
2-1will appear

14
S
I
U
USER MANUAL
Figure 2-3
After activating the WIFI mode through the
phone settings, access the available WIFI
connection section, check for the presence of
the Innova 2.0 network and connect to it.
N.B.: with Android devices the procedure
above is automatic, but for IOS devices you
have to edit main settings of your phone /tablet
and select the "Innova2.0" network on network
settings.
Figure 2-4
Figure 2-5
Once connected to the WIFI network of the
device, the screen of your product will appear
and you will be able to name it and indicate
its serial number, consisting of 9 alphanumeric
characters as shown in the figure.
By entering the password, the stand alone
Innova2.0 network will be protected from
unauthorised access.
N.B.: for IOS devices, after 2.0 label appliance,
the WiFi network will automatically change
for find a network with Internet access. So
is necessary to edit another time the phone
network settings and reconnect to the new
2.0 label just named, e.g. "Innova2.0_2.0".
Figure 2-6
Figure 2-8Figure 2-7
If you go back to the main menu and access
the menu "My products", the air conditioner
units in the network will be displayed and can
be changed and/or scheduled as you wish.
Moreover, new devices can be searched for,
installed and configured as in Figura 2-18 3.

15
S
I
U
EN
USER MANUAL
Figure 2-11
Once you entered the WIFI connection menu,
choose the network preferred for Internet
access and select it.
Figure 2-12
Figure 2-9
At this point, a general air conditioner control
screen will appear, by means of which you can
control and manage your air conditioner 2.0.
N.B.: from now on you will have the possibility
to control the air conditioner via the local WIFI
network, but not via Internet.
To do this, it is necessary to take a further step
and connect to the home/office WIFI network
by accessing the settings as in the figure on
the right and selecting the option "Remote
Control".
Figure 2-10
Figure 2-13
Then enter the password of your WIFI network
and confirm it.
N.B.: on password label are available only
alpha numeric characters, not special ones.
Figure 2-14

16
S
I
U
USER MANUAL
Figure 2-17
Click on the edit key as indicated to change
the operating mode of the air conditioner.
Figure 2-18
Figure 2-19
From the main screen of the selected
conditioner, it is possible to change the
operating mode from manual to automatic and
then access the timer as shown in the figures.
Figure 2-20
Figure 2-15
At this point Innova 2.0 App will attempt to
connect your unit to your home network; thus,
smartphone air conditioner main screenshot for
the management of the unit will appear again.
From now on, your 2.0 is connected to the
server trough Internet network, and can be
managed from all over the world via WIFI or
your phone's data connection!
If the procedure fault, smartphone/tablet will
automatically connect to 2.0 local network.
In this case, repeat the procedure by checking
password and network label.
Figure 2-16

17
S
I
U
EN
USER MANUAL
Figure 2-21
Follow the procedure indicated above to add on and off times during the day.
It is possible to program multiple on and off times with minimum intervals of thirty minutes in the same day.
If you want to repeat these periods in other days of the week, it will be possible by following the instructions
shown in the figures below.
Figure 2-22 Figure 2-23
Figure 2-24 Figure 2-25 Figure 2-26

18
S
I
U
USER MANUAL
Figure 2-27
After finishing the programming operation, the
screen of the operating mode will be as in
Figura 2-27 3.
If we then go back to the main screen of the air
conditioner as in Figura 2-28 at the bottom, the
time of the first start-up of the air conditioner
will be displayed if the off time is scheduled.
Figure 2-28
COUPLING 2.0 WITH NEW SMARTPHONE OR
TABLET
After 2.0 configuration with smartphone, it is possible to
control the unit with another device (smartphone or tablet);
the quick procedure is the following.
You shall to connect to the same network of 2.0 just
configured;
Download and install “InnovApp DuePuntoZero” apllication
from store. Open the app and press to "start" button
(Figure 2-2).
Now the smartphone will tell you that you are not
connected to the right WiFi network and you shall connect
to “Innova2.0” network: ignore the warning and click to
“devices” under loading menu.
Now the phone, if you are connecteed to same WiFi
network where is also connected the 2.0 air conditioner,
will automatically scan all the 2.0 available on network.
Once your device found, will be opened the “2.0” menu;
now you can cocontrol the 2.0 also with the second tablet/
amartphone.
To add new 2.0, select the menu key on the left of your
screen (“my devices” settings) and click “+” key that
appear on top and right of your screen.
Now two lanels will appear: “find new devices”, “manual
add”); select “find new devices”; so the smartphone will
search new air conditioners another time.
WIFI NETWORK RESET
With “reset” function is possible to resume the configuration
from begin with a few steps :
• check if air conditioner is powered Off;
• Hold down the key for 5 seconds. When “On” label
appears, release the key.
• Press key another time to change WiFi status
(On,Rst,Off). The needed setting will be activated
automatically after 10 seconds without selections.
• If we leave “On” blinking, the Wi-Fi network will be
active and you can see the 2.0 with the last WiFi
name set.
• Leaving “Off” setting, the 2.0 Wi-Fi will switch off
and it will not visible by smartphone/tablet.
• Leaving “Rst” setting, the 2.0 WiFi network back
to default setting named "Innova2.0"; so you will
have to configure the air conditioner from Figure 2-3
indications.

19
S
I
U
EN
NOTES

INNOVA s.r. l .
Fraz . St rada, 16 - 38085 PIEVE DI BONO (TN) - ITALY
tel. [phone] fax [phone]
[email protected]
realized with iés technology by
N273027A - Rev. 0N273027C - Rev. 00
INNOVA s.r.l.
Via I Maggio 8 - 38089 STORO (TN) - ITALY
tel. [phone] fax [phone]
[email protected]