INOXPA INNOVA T Manual

10.252.32.0029
TANK BOTTOM MIXPROOF VALVE
INNOVA T
Original Instructions
10.252.30.05EN
(0) 2023/10
INSTALLATION, SERVICE AND MAINTENANCE INSTRUCTIONS

E C D e c l a r a t i o n o f C o n f o r m i t y
Model:
INOXPA S.A.U.
Telers, 60
17820 - Banyoles (Spain)
hereby declare under our sole responsibility that the
Type:
Serial number:
INNOVA
T
Technical O󰀩ce Manager
3rd October 2023
10.252.30.06EN
(0) 2023/10
Document:
Revision:
Machine: TANK BOTTOM MIXPROOF VALVE
David Reyero Brunet
fullls all the relevant provisions of the following directive:
Machinery Directive 2006/42/EC
Pressure Equipment Directive 2014/68/EU1
Regulation (EC) nº 1935/2004
Regulation (EC) nº 2023/2006
and with the following harmonized standards and/or regulations:
EN ISO 12100:2010, EN ISO 13732-1:2008, EN 1672-2:2005+A1:2009,
EN ISO 14159:2008, EN 12266-1:2012, EN 19:2016
The technical le has been prepared by the signer of this document.
Size: DN 40 - DN 100 / OD 1½’’ - OD 4’’
IXXXXXXXXX to IXXXXXXXXX
XXXXXXXXXIINXXX to XXXXXXXXXIINXXX
1
DN≤25 Designed and manufactured in accordance with the sound engineering practice
DN>25 Class I equipment. Conformity assessment procedure used: Module A

D e c l a r a t i o n o f C o n f o r m i t y
Model:
INOXPA S.A.U.
Telers, 60
17820 - Banyoles (Spain)
hereby declare under our sole responsibility that the
Type:
Serial number:
INNOVA
T
Technical O󰀩ce Manager
3rd October 2023
10.252.30.07EN
(0) 2023/10
Document:
Revision:
Machine: TANK BOTTOM MIXPROOF VALVE
David Reyero Brunet
fullls all the relevant provisions of the these regulations:
Supply of Machinery (Safety) Regulations 2008
Pressure Equipment (Safety) Regulations 20161
and with the following designated standards:
EN ISO 12100:2010, EN ISO 13732-1:2008, EN 1672-2:2005+A1:2009,
EN ISO 14159:2008, EN 12266-1:2012, EN 19:2016
The technical le has been prepared by the signer of this document.
Size: DN 40 - DN 100 / OD 1½’’ - OD 4’’
IXXXXXXXXX to IXXXXXXXXX
XXXXXXXXXIINXXX to XXXXXXXXXIINXXX
1
DN≤25 Designed and manufactured in accordance with the sound engineering practice
DN>25 Class I equipment. Conformity assessment procedure used: Module A

1. Table of Contents
1. Table of Contents
2. Generalities
2.1. Instructions manual ........................................................................................................................................... 5
2.2. Compliance with the instructions.................................................................................................................. 5
2.3. Warranty ............................................................................................................................................................... 5
3. Safety
3.1. Warning symbols................................................................................................................................................ 6
3.2. General safety instructions............................................................................................................................. 6
4. General Information
4.1. Description ........................................................................................................................................................... 7
4.2.Application............................................................................................................................................................ 7
5. Installation
5.1. Reception of the valve...................................................................................................................................... 8
5.2.Transport and storage ...................................................................................................................................... 8
5.3. Identication of the valve................................................................................................................................. 8
5.4. Location .............................................................................................................................................................. 10
5.5. Flow direction .................................................................................................................................................... 10
5.6. General installation ......................................................................................................................................... 10
5.7. Checking and review .......................................................................................................................................11
5.8. Welding ................................................................................................................................................................11
5.9. Connecting the air to actuator ......................................................................................................................11
5.10. Connecting the air to actuator................................................................................................................... 12
6. Start-up
7. Operating problems
8. Maintenance
8.1. General considerations.................................................................................................................................. 15
8.2. Maintenance...................................................................................................................................................... 15
8.3. Cleaning.............................................................................................................................................................. 16
8.4. Disassembly and assembly the valve....................................................................................................... 17
8.5. Replacing the seat seal ................................................................................................................................. 21
8.6. Disassembly and assembly of the actuator ............................................................................................ 22
9. Technical Specications
9.1. Valve .................................................................................................................................................................... 24
9.2.Actuator............................................................................................................................................................... 24
9.3. Materials ............................................................................................................................................................. 24
9.4. Sizes available.................................................................................................................................................. 24
9.5. Weights ............................................................................................................................................................... 25
9.6. Dimensions ........................................................................................................................................................ 25
9.7. Exploded drawing and parts list.................................................................................................................. 26
4INOXPA S.A.U. 10.252.30.05EN · (0) 2023/10

2. Generalities
2.1. INSTRUCTIONS MANUAL
This manual contains information about the reception, installation, operation, assembly and mainte-
nance of the tank bottom mixproof valve INNOVA T.
Carefully read the instruction prior to starting the valve, familiarize yourself with the installation, ope-
ration and correct use of the valve and strictly follow the instructions. These instructions should be
kept in a safe location near the installation area.
The information published in the instruction manual is based on updated data.
INOXPA reserves the right to modify this instruction manual without prior notice.
2.2. COMPLIANCE WITH THE INSTRUCTIONS
Not following the instructions may impose a risk for the operators, the environment and the machine,
and may cause the loss of the right to claim damages.
This non-compliance may cause the following risks:
- failure of important machine/plant functions,
- failure of specic maintenance and repair procedures,
- possible electrical, mechanical and chemical hazards,
- risk to the environment due to the type of substances released.
2.3. WARRANTY
The conditions of the warranty are specied in the General Sales Condition that has been delivered
at the time of placing your order.
Please do not hesitate to contact us in case of doubts or if further explanations are required regar-
ding specic data (adjustments, assembly, disassembly, etc.).
The machine may not undergo any modication without prior approval from the manu-
facturer.
For your safety, only use original spare parts and accessories. The usage of other parts
will relieve the manufacturer of any liability.
Changing the service conditions can only be carried out with prior written authorization
from INOXPA.
The non-compliance of the prescribed indications in this manual means misuse of this gear on the
technical side and the personal safety and this exempts INOXPA of all responsibility in case of ac-
cidents and personal injuries and/or property damage. Also, excluded from the warranty all break-
downs caused by improper use of the gear.
Generalities
5
INOXPA S.A.U. 10.252.30.05EN · (0) 2023/10

3.1. WARNING SYMBOLS
3. Safety
Safety hazard for people in general and/or equipment
ATTENTION Important instruction to prevent damage to the equipment and/or its function
3.2. GENERAL SAFETY INSTRUCTIONS
3.2.1. During installation
Read the instruction manual carefully before installing and starting the valve. Contact
INOXPA in case of doubt.
Always take into account the Technical Specications of chapter 9.
The installation and use of the valve should always be in accordance with applicable
regulations regarding health and safety.
Before starting up the valve, check that it is assembled correctly and its shaft is perfectly
aligned. Incorrect alignment and/or excessive stress during coupling can cause serious
mechanical problems in the valve.
3.2.2. During operation
Always take into account the Technical Specications of chapter 9.
NEVER exceed the specied limit values.
NEVER touch the valve and/or piping that is in contact with the uid during operation. If
the process involves hot products there is a risk of burns.
The valve contains parts that move in a linear fashion. Do not place hands or ngers in
the valve closing area. This can cause serious injury.
3.2.3. During maintenance
Always take into account the Technical Specications of chapter 9.
NEVER disassemble or remove the valve until the pipes have been emptied. Bear in
mind that the uid in the pipe may be hazardous or extremely hot. Consult the regula-
tions in e󰀨ect in each country for these cases.
Inside the actuator there is a spring with an applied load. The steps specied in this ma-
nual must be followed when performing maintenance operations to avoid injury.
Do not leave loose parts on the oor.
Safety
INOXPA S.A.U. 10.252.30.05EN · (0) 2023/10
6

4. General Information
The tank bottom mixproof valve INNOVA T is a pneumatic shut-o󰀨 double seat valve. The INNOVA
T valve has two independent seats which form a leak detection chamber at atmosphere pressure
for all operating conditions. In the case that a leaked product occurs, the product will enter the leak
detection chamber, an it will discharge through the leak outlet. The leak detection chamber is closed
when the valve is open, enabling the product to transfer from the tank to the pipe. The valve can be
cleaned to any level, depending on the process needs.
4.1. DESCRIPTION
4.2. APPLICATION
The tank bottom mixproof valve is designed to be installed in tanks and vats for hygienic applications.
10.252.32.0030
General Information
7
INOXPA S.A.U. 10.252.30.05EN · (0) 2023/10

INOXPA is not liable for any deterioration of the material caused by its transport or unpac-
king.
When receipt the valve, check to see whether all the parts listed on the delivery slip are present:
- complete valve,
- its components if any are supplied,
- instruction manual.
INOXPA inspects all its equipment before packaging. However, it cannot guarantee that the mer-
chandise arrives at the user intact.
When unpacking the valve:
- remove any possible traces of packaging from the valve or its parts,
- inspect the valve or the parts that comprise it for possible damage incurred during shipping,
- take all possible precautions against damage to the valve and its components.
5.1. RECEPTION OF THE VALVE
5. Installation
5.2. TRANSPORT AND STORAGE
Take all possible precautions when transport and storage the valve to avoid damage it and its com-
ponents.
5.3. IDENTIFICATION OF THE VALVE
Each valve is inscribed with its fabrication number. Indicate the fabrication number on all documents
to refer to the valve.
The buyer or user shall be liable for assembly, installation, start-up and operation of the
valve.
Type
Air
Serial
Size
Year
C. TELERS, 60 - 17820 BANYOLES
GIRONA (SPAIN) . www.inoxpa.com
INOXPA S.A.U.
R
10.251.32.0043
Installation
INOXPA S.A.U. 10.252.30.05EN · (0) 2023/10
8

WB T L 0 - 0 06 52 050 12 0
Options
0ID Ra ≤ 0,8
1ID Ra ≤ 0,5
Actuator
11 T1 S/E NC
12 T2 S/E NC
13 T3 S/E NC
Size
040 DN 40, OD 1½’’ 076 OD 3’’
050 DN 50, OD 2’’ 080 DN 80
063 OD 2½’’ 100 DN 100, OD 4’’
065 DN 65
Seals
43 HNBR
52 EPDM
78 FPM
Material
06 1.4404 (AISI 316L)
Connection
0 Weld
Standard pipe
0 DIN
1 OD
Body conguration
L,T 1 body
Type
T tank bottom mixproof valve
Product family
WB INNOVA valve
Installation
9
INOXPA S.A.U. 10.252.30.05EN · (0) 2023/10

5.4. LOCATION
Place the valve leaving enough space around it to realize easily the dismantling, the inspection and
the review the valve as well as in order to access to the actuator air connection’s device for valves
with automatic actuation even when the valve is operating. Consult in chapter 5.8. Welding the re-
quired minimum distances. The installation should allow that the removable parts are could remove
easily.
5.5. FLOW DIRECTION
After the location of the valve is dened, the valve can be joined to the pipe by welding the valve
housing or using ttings.
In case of joining the valve to the pipe by ttings do not forget the
seals and tighten the unions properly.
If instead, the valve is joined by welding, before starting to weld the
valve bodies to the pipe disassemble the valve to prevent damage to
the joints, following the instructions in chapter 8.4. Disassembly and
assembly the valve.
During installation, the valve avoids using excessive force and pay
special attention to:
- vibrations that may be produced on the facility,
- hermal dilation that the pipe may undergo when hot uids are
circulating,
- the weight that the pipe can support,
- excessive welding current.
5.6. GENERAL INSTALLATION
The following image indicates the recommended ow direction and the closed direction. Following
these indications will avoid the water hammer that can occur when the valves are closed and its
consequences as far as possible.
The recommended direction has to be the opposite of the closing movement of the valve. The valve
works always against the uid pressure when the valve is closed.
10.252.32.0031
10.252.32.0032
Installation
INOXPA S.A.U. 10.252.30.05EN · (0) 2023/10
10

5.7. CHECKING AND REVIEW
Perform the following checks before using the valve:
- check that the clamps and nuts are tightened,
- if the valve is tted with a pneumatic drive, apply the compressed air several times, checking
that the valve carries out the opening and closing action without di󰀩culty.
To perform the welding works:
- disassemble the valve as indicated in chapter 8.4. Disassembly and assembly the valve,
- weld the valve body to the pipes, maintaining the minimum distance indicated in the following
table. This will allow for the disassembly of the valve, doing the subsequent reviews and chan-
ging the necessary valve pieces like seals, bushings, etc.
Welding work should only be done by qualied persons who are trained and equipped
with the necessary equipment to perform this kind of work.
5.8. WELDING
Valve size D1
[mm]
D2
[mm]
h
[mm]
DN 40 / OD 1½’’ 155 150 3
DN 50 / OD 2’’ 165 160 3
DN 65 / OD 2½’’ 215 210 3
DN 80 / OD 3’’ 215 210 3
DN 100 / OD 4’’ 255 250 3
D2
D1
h
h
10.252.32.0033
5.9. CONNECTING THE AIR TO ACTUATOR
The valve conguration is normally closed (NC).
Never disassemble the clamps of the valve without reading the instructions carefully
since the actuator contains a spring inside it with an applied load.
Valve and actuator assembly and disassembly only should be done by qualied persons.
Installation
11
INOXPA S.A.U. 10.252.30.05EN · (0) 2023/10

To perform the air connection to the actuator:
- connect and check the air connections (G 1/8’’ thread for tubing Ø6 mm) with thread in accor-
dance with double-e󰀨ect or simple e󰀨ect needs.
- mind the quality of the compressed air according to the specications described in chapter 9.
Technical Specications.
5.10. CONNECTING THE AIR TO ACTUATOR
Air connections
G 1/8’’ thread
10.252.32.0034
A1
A2
A3
Installation
INOXPA S.A.U. 10.252.30.05EN · (0) 2023/10
12

6. Start-up
Before putting the valve or the actuator into service the following must be taken into consideration:
- check that the piping and valve are completely free of possible traces of welding slag or other
foreign particles. Clean the system if necessary,
- check to make sure the valve moves smoothly. If necessary, lubricate it with special grease or
soapy water,
- check for possible leaks, and make sure the pipes and their connections are sealed and do not
have any leaks,
- if the valve has been supplied with an actuator, make sure that the alignment of the valve shaft
and the actuator shaft enables smooth movement,
- check that the compressed air pressure at the inlet of the actuator matches what is indicated in
chapter 9. Technical Specications,
- consider the quality of the compressed air, according to the specications described in chapter
9. Technical Specications,
- activate the valve.
Read carefully the instructions in chapter 5. Installation before start-up the valve.
Before start-up, the persons in charge must be duly informed about how the valve works
and the safety instructions to follow. This instruction manual will be available to person-
nel at all times.
ATTENTION
Do not modify the operating parameters for which the valve has been designed without
prior written authorisation from INOXPA.
Do not touch the moving parts of the coupling between the actuator and the valve when
the actuator is connected to the compressed air supply.
¡Burn hazard! Do not touch the valve or the pipes when hot uids are circulating or when
cleaning and/or sterilization are being carried out.
Start-up
13
INOXPA S.A.U. 10.252.30.05EN · (0) 2023/10

7. Operating problems
The upper shaft does not rise during impulses
The individual seats do not clean
Internal leak of product (valve closed)
Jerky valve operation
POSSIBLE CAUSES SOLUTIONS
•The seal or guide bushing is worn, deteriorated
or has gotten stuck
Replace the seals.
Replace the seals with ones made of a di󰀨erent
material or grade that is more appropriate for the
product.
Lubricate with soapy water or a lubricant that is
ocmpatible with the seal material and the product.
• Normal seal wear Replace the seals.
•Premature wear of the seal/a󰀨ected by the
product
Replace the seals with ones made of a di󰀨erent
material or grade that is more appropriate for the
product.
Reducte the pressure in the line.
Lower the operating temperature.
•Product residue has deposited on the valve seat
and/or plug Clean frequently
•Product pressure exceeds the actuator specica-
tions Reduce the product pressure
•Excessive product pressure in body Reduce the product pressure
•Loss of seal (vibrations) Tighten loose parts
• • Insu󰀩cient time for impulses Adjust cleaning time in control system
•Insu󰀩cient air pressure Increase the compressed air pressure
Operating problems
INOXPA S.A.U. 10.252.30.05EN · (0) 2023/10
14

8. Maintenance
This valve, just like any other machine, requires maintenance. The instructions in this chapter cover
the maintenance of the valve, the identication and replacement of the spare parts and the disas-
sembly and assembly of the valve. The instructions are aimed at maintenance personnel and those
responsible for the supply of spare parts.
8.1. GENERAL CONSIDERATIONS
Read carefully the chapter 9. Technical Specications.
Maintenance work should only be done by qualied persons who are trained and equi-
pped with the necessary equipment to perform this kind of work.
All replaced material should be duly disposed or recycled according to the directives in
e󰀨ect in each area.
Make sure that the pipes are not under pressure before starting maintenance work..
8.2. MAINTENANCE
To perform maintenance properly is recommended:
- periodic inspection of the valve and its components,
- keeping an operational record of each valve writing down any problems,
- always having spare replacement seals in stock.
Pay special attention to the hazard warnings indicated in this manual during the performance of the
maintenance work.
The valve and the pipes must never be under pressure during maintenance.
¡Burn hazard! Do not touch the valve or the pipes when hot uids are circulating or when
cleaning and/or sterilization are being carried out.
The time interval between each preventive maintenance may vary in accordance with the work con-
ditions to which the valve is subject: temperature, pressure, number of operations per day, type of
cleaning solutions used, etc.
8.2.1. Maintenance of the seals
REPLACING SEAL
Preventive maintenance Replace after 12 months
Maintenance after a leak Replace at the end of the process
Planned maintenance
Regularly check the absence of leaks and the smooth ope-
ration of the valve.
Keep a record of the valve’s maintenance.
Use statistics for planning inspections.
Lubrication
During assembly, apply lubricants that are suitable with the
material of which the seat seal is made. See the following
table.
SEAL COMPONENT LUBRICANT NLGI DIN
51818 Class
HNBR / FPM klübersynth UH 1 64-2403 3
EPDM / HNBR / FPM PARALIQ GTE 703 3
Maintenance
15
INOXPA S.A.U. 10.252.30.05EN · (0) 2023/10

8.2.2. Storage
The valves should be stored in a closed area under the following conditions:
- temperature between 15ºC y 30ºC,
- air humidity < 60%
Storage of the equipment outdoors is NOT allowed.
8.2.3. Spare parts
To request spare parts is necessary to indicate the type of valve, the size, the fabrication number,
the position and the description of the part which can be found in chapter 9. Technical Specications.
8.3. CLEANING
The use of aggressive cleaning products such as caustic soda and nitric acid may burn
the skin.
Wear rubber gloves during all cleaning procedures.
Always wear protective goggles.
Two types of solutions can be used for CIP processes:
a. alkaline solution: 1% by weight of caustic soda (NaOH) at 70ºC (150ºF). To make this solution:
1 kg NaOH + 100 l H2O1= cleaning solution
2,2 l NaOH at 33% + 100 l H2O = cleaning solution
b. acid solution: 0,5% by weight of nitric acid (HNO3) at 70ºC (150ºF). To make this solution:
0,7 l HNO3at 53% + 100 l H2O = cleaning solution
1) only use chlorine-free water to mix with the cleaning agents
8.3.1. CIP (clean-in-place) cleaning
If the valve is installed in a system with a CIP process, its disassembly will not be required. EPDM
is the standard seal material that will be used for CIP cleaning, both in alkaline mediums and in acid
mediums. The materials of the seal HNBR and FPM are not recommended.
ATTENTION
Check the concentration of the cleaning solutions. An incorrect concentrations may lead
to the deterioration of the valve seals.
To remove any traces of cleaning products, ALWAYS perform a nal rinse with clean water at the end
of the cleaning process.
Clean the entire interior and exterior of the valve before starting disassembly and assem-
bly tasks.
8.3.2. Automatic SIP (sterilization-in-place)
Sterilization with steam is applied to all equipment including the pipping.
Maintenance
INOXPA S.A.U. 10.252.30.05EN · (0) 2023/10
16

8.4. DISASSEMBLY AND ASSEMBLY THE VALVE
The following tools are needed in order to disassembly and assembly the valve and the drives:
- a spanner crescent to unscrew the top shaft from the bottom shaft of the valve:
Proceed with caution. Personal injury can occur.
Always disconnect the compressed air before starting to disassemble the valve.
Never disassemble the valve clamps directly without reading the instructions carefully,
since the actuator contains a spring inside it with an applie load.
Valve and actuator assembly and disassembly should only be done by qualied persons.
- 17 mm crescent spanner to separate the lantern from the actuator,
- 2 mm Allen wrench to loosen the sleeve bolt of the valve,
- appropiate tool (not piercing) to mount the seat seals.
Maximum conditions during the SIP process with steam or superheated water:
a. maximum temperature: 140ºC / 284ºF
b. maximum time: 30 min
c. cooling: sterile air or inter gas
d. materials: EPDM (the materials HNBR and FPM are not recommended)
ATTENTION
Do NOT start the equipment during the sterilization with steam.
The parts and the materials will not be damaged if the indications specied in this manual
are observed.
No cold uid can enter the equipment until the temperature of the equipment is lower
than 60ºC (140ºF).
Valve size DN 40
OD 1½
DN 50
OD 2’’
DN 65/80
OD 2½’’ - 3’’
DN 100
OD 4’’
Actuator 17 mm
Bottom shaft 8 mm 12 mm
Maintenance
17
INOXPA S.A.U. 10.252.30.05EN · (0) 2023/10

8.4.1. Disassembly
1. Apply compressed air to the actuator (10) A2
connection to move the valve shafts (08,08A) to
the open position.
2. Loosen and separate the clamp (34) that joins
the body (01) to the lantern.
3. Separate the assembled formed by the actua-
tor (10) and the shafts (08,08A) from the valve
body (01).
4. Release the compressed air from the actuator
(10) A2 connection.
5. Apply compressed air to the actuator (10) A3
connection.
6. Unscrew the internal shaft (08A) from the val-
ve while xing the actuator shaft.
7. Release the compressed air from the actuator
(10) A3 connection.
8. Loose the xation sleeve bolt (23A) and slide
the xation sleeve (35) to the actuator (10).
9. Remove the shaft xation core (55).
10. Unscrew the valve air tting (18B).
11. Disassemble the external shaft (08).
12. Remove the O-rings (20C,20A) and the di󰀨u-
ser (44) from the external shaft (08).
13. Remove the body cover (12) from the body.
14. Remove the shaft seal (05), the O-ring (20B)
and the guide bushing (17) from the body cover
(12).
15. Remove the radial seat (05E) seal from the
internal shaft (08A) and the conical seat (05C)
and at seat (05D) seals from the external shaft
(08) following the instructions of chapter 8.5. Re-
placing the seat seal.
16. Disassemble the screws (23) that join the lan-
tern (21) to the actuator (10).
17. Separate the lantern (21) to the actuator (10).
18. Remove the bushing (42).
8.4.2. Assembly
1. Place the bushing (42) to the actuator (10).
2. Place the lantern (21) on the bushing (42) and
x it with the screws (23).
3. Place the radial seat (05E) seal on the internal
shaft (08A) and the conical seat (05C) and the
at seat (05D) seals on the external shaft (08) fo-
llowing the instructions of chapter 8.5. Replacing
the seat seal.
4. Place the xation sleeve (35) on the actuator
shaft (10).
5. Mount the shaft seal (05), the O-ring (20B) and
the guide bushing (17) on the body cover (12).
6. Place the body cover (12) on the lantern (21).
7. Mount the O-ring (20C,20A) and the di󰀨user
(44) on the external shaft (08).
8. Place the external shaft (08) on the actuator
shaft and x both with the shaft xation core (55).
9. Slide the xation sleeve (35) and x it with the
bolt (23A).
10. Apply compressed air to the A3 connection of
the actuator (10).
11. Place the internal shaft (08A) and screw it
while the actuator (10) shaft is xed.
12. Screw the valve air tting (18B).
13. Release the compressed air from the A3 con-
nection of the actuator (10).
14. Apply compressed air to the A2 connection of
the actuator (10).
15. Place the valve body (01) on the lantern (21)
and x it with the clamp (34).
16. Release the compressed air from the A2 con-
nection of the actuator (10).
Maintenance
INOXPA S.A.U. 10.252.30.05EN · (0) 2023/10
18

08A
34 08
10
01
21
A2
1
2
3
4
10
08A
08
A3
18B
55
10
23A
35
21
08
35
12
10
21
08
17
05
12
20B
20A
44
20B
08
Maintenance
19
INOXPA S.A.U. 10.252.30.05EN · (0) 2023/10

23
42
10
21
08 08A
05C
05E
05D
5
6
10.252.32.0036
Maintenance
INOXPA S.A.U. 10.252.30.05EN · (0) 2023/10
20