Insignia NS-HW36A217 User manual

We recommend that you use a professional
electrician to install the USB charger wall outlet. For
information about electrical specications, see
SPECIFICATIONS.
SAFETY
Warnings:
• RISK OF ELECTRIC SHOCK — Use only in dry
locations and only indoors.
• All cables should be routed away from the charger
outlet openings.
• DO NOT use with any aquarium equipment.
• DO NOT install in an outlet that is not grounded.
Notes to the installer:
• This device must be installed in accordance with
National and Local electrical codes.
• To prevent severe shock or electrocution, always
turn power OFF at the service panel before
working with wiring.
• This device should be used with copper or
copper-clad wire. DO NOT use with aluminum
wire.
• DO NOT plug this device into a shallow wall box.
The wall box must be deep enough to house the
charger outlet. If the box is too shallow, the
charger outlet will not t securely into the wall.
PACKAGE CONTENTS
• 3.6A USB Charger Wall Outlet
• White decora-style wall plate
• Screws: 2 long and 2 short
• Quick Setup Guide
FEATURES
• Replaces a standard duplex outlet
• Quickly charges USB devices
• Tamper-resistant outlets for added safety
• Provides two USB ports with 3.6A total output
• Provides two standard 110V power outlets
• Works in nearly all installations
• Compatible with your existing decora wall plate
Before using your new product, please read these instructions to prevent any damage.
INSTALLING THE CHARGER
1 Warning: DISCONNECT POWER. Failure to do
so can result in severe injury or death.
Make sure that you disconnect power to the
circuit by removing the fuse from the circuit
breaker or turning OFF the circuit breaker.
2 Remove the wall plate and mounting screws
that cover the old outlet.
3 Carefully remove the existing outlet from the
wall box.
4 Disconnect the wiring from the old outlet. Note
the wire positions. Connect the charger outlet
wires the same way.
5 Connect the wires to the charger outlet:
• Black lead attaches to the hot wire(s)
• White lead attaches to the neutral wire(s)
• Green lead attaches to the ground wire(s)
QUICK SETUP GUIDE
3.6A
USB Charger
Wall Outlet
NS-HW36A217
Electrical
outlets (2)
USB ports (2)
Final at size: 12 × 4.7 in. (304.8 × 119.38 mm)
Final fold size: 3 × 4.7 in. (76.2 × 119.38 mm)
Hot
(black)
Neutral
(white)
Ground
(green)
NS-HW36A217_16-0670_QSG_V3_FINAL_ENG.ai 1 9/1/2016 3:29:21 PMNS-HW36A217_16-0670_QSG_V3_FINAL_ENG.ai 1 9/1/2016 3:29:21 PM

V3 ENGLISH 16-0670
Insert the straightened wire into either of the two
holes of the hot and neutral locations on the side of
the outlet. Power passes between the two
corresponding holes for pass-thru wiring. Attach
the ground wire to the bottom of the outlet.
6Tighten every screw and make sure that no
bare copper wire is exposed. When tightening
screws, use 14 pounds-per-inch of torque.
7Carefully insert the
charger outlet into the
wall box.
8Secure the charger
outlet to the wall box
with the two long
screws (provided).
9Secure the wall plate
to the charger outlet
with the two short
screws (provided).
10 Restore power by
replacing the fuse or
turning on the
circuit breaker. The
charger outlet is
ready to use.
USING THE CHARGER OUTLET
• To charge USB devices (like mobile phones or
tablets), plug USB cables into the USB ports on
the charger outlet and into the USB ports on the
devices.
• To power electrical devices (like lamps or
notebooks), plug them into the electrical outlets.
SPECIFICATIONS
Dimensions (L × W × H)
With plate:
4.7 × 3 × 1.9 in. (120 × 76 × 47.5 mm)
Without plate:
4.2 × 1.7 × 1.9 in (106 x 43 x 47.5 mm)
Electrical
Receptacle Rating: 15Amp, 125VAC
USB Rating: Two USB ports with total 3.6A, 5V DC
Line voltage: 125V AC @ 60 Hz
Wire Terminals: #14-#12 AWG
LEGAL NOTICES
FCC Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Warning: Changes or modications not expressly approved
by the party responsible for compliance could void the
user's authority to operate the equipment.
ONE-YEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
For customer service, call 877-467-4289 (U.S. and
Canada) or 01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated companies
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2016 Best Buy. All rights reserved
Made in China
NS-HW36A217_16-0670_QSG_V3_FINAL_ENG.ai 2 9/1/2016 3:29:21 PMNS-HW36A217_16-0670_QSG_V3_FINAL_ENG.ai 2 9/1/2016 3:29:21 PM