Insignia NS-HWMC1848 User manual

SAFETY INFORMATION AND SPECIFICATIONS .2
PACKAGE CONTENTS: PARTS ..................................4
PACKAGE CONTENTS: HARDWARE.......................5
ASSEMBLY INSTRUCTIONS ......................................7
CARE AND MAINTENANCE ................................... 33
Wood Finish 3-in-1 TV
Stand for TVs up to
55”/135 lbs.
NS-HWMC1848
Before using your new product, please read these instructions to prevent any damage.
USER GUIDE
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 1 Tuesday, March 7, 2017 3:08 PM

2
3-in-1 TV STAND
www.insigniaproducts.com
SAFETY INFORMATION
AND SPECIFICATIONS
CAUTION: The top surface of this stand
is designed for use with a product
weighing no more than
135 lbs. (61.2 kg) and having a width that
permits it to sit evenly on the stand with
no more than a one-inch overhang on each side of
the shelf. Use with products that weigh more than
the maximum weight allowed, or with dimensions
that extend beyond the maximum width may result
in instability, which may result in injury.
CAUTION: This product contains small
items that could be a choking hazard if
swallowed. Keep these items away from
young children!
Maximum overall weight: 235 lbs (106.6 kg)
Maximum top shelf weight: 135 lbs (61.2 kg)
Maximum lower shelf weight: 50 lbs (22.6 kg)
Maximum TV weight on swivel stand: 135 lbs
(61.2 kg)
Recommended screen range: 37" - 55” diag.
(32.5 - 49.75” width)
Overall dimensions (H × W × D):
55.25 × 47.75 × 22.5 in. (140.3 x 121.2 x 57.2 cm)
TV stand weight: 81.6 lbs (37 kg)
Vesa Compatibility: 100 x 100 mm, 200 x 100 mm,
200 x 200 mm, 200 x 300 mm, 200 x 400 mm, 300 x
300 mm, 400 x 300 mm, 400 x 400 mm, 600 x 400 mm
32 inch
(81.3 cm)
8.75 inch
(22.2 cm)
55.25 inch
(140.3 cm)
7.2 inch
(18.3 cm)
7.7 inch
(19.5 cm)
22 inch
(55.8 cm) 47.75 inch
(121.2 cm)
15.8 inch
(40.2 cm)
15 inch
(38 cm)
18.4 inch
(46.8 cm)
43.8 inch
(111.2 cm)
39.75 inch
(101 cm)
22.5 inch
(57.2 cm)
47.75 inch
(121.2 cm)
20 inch
(50.8 cm)
20 inch
(50.8 cm)
33.25 inch
(84.45 cm)
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 2 Tuesday, March 7, 2017 3:08 PM

3
3-in-1 TV STAND
www.insigniaproducts.com
Tools needed:
Phillips screwdriver
Level
Power drill
Hammer
Edge-to-edge stud finder
Pencil
3/8” drill bit (for tipping
restraint)
3/16” wood drill bit
or
7/16” masonry drill bit
1/2” Socket wrench
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 3 Tuesday, March 7, 2017 3:08 PM

4
3-in-1 TV STAND
www.insigniaproducts.com
PACKAGE CONTENTS: PARTS
Make sure that you have all the parts necessary to assemble your new TV stand.
ALeft side frame (1) BRight side frame (1)
DBottom crossbar (1)
EBottom left rail (1)
CLong rear support (1)
F Bottom right rail (1) GBack stretcher (2) HSupport leg (2)
I Top shelf (1) J Middle shelf (1)
KBottom shelf (1)
LBack panel (1)
NMounting frame (1)
MSwivel bracket (1) PTV brackets L/R (2)
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 4 Tuesday, March 7, 2017 3:08 PM

5
3-in-1 TV STAND
www.insigniaproducts.com
PACKAGE CONTENTS: HARDWARE
Note: You may receive extra hardware.
Make sure that you have all the hardware necessary to assemble your new TV stand.
Label Hardware Qty.
Q2
R4
S4
T14
U16
V12
W46
Cable clip
Screw #4 x
10 mm
Bolt 1/2”
(12.7 mm)
Bolt 5/8”
(15.87 mm)
Bolt 1 5/8”
(41,27 mm)
Bolt 2 1/4”
(57.15 mm)
Lock washer
Label Hardware Qty.
X46
Y4
Z1
AA 4
BB 4
CC 4
DD 1
EE 2
FF 1
Flat washer
Hex nut
Hex wrench 3/16” (4.76 mm)
Lag bolt
Large flat washer
Concrete anchor
Open wrench
Hex wrench 0.158” (4 mm)
Touch-up pen
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 5 Tuesday, March 7, 2017 3:08 PM

6
3-in-1 TV STAND
www.insigniaproducts.com
PACKAGE CONTENTS: HARDWARE (continued)
Label Hardware Qty.
GG 1
HH 4
II 4
JJ 4
KK 4
LL 4
MM 4
NN 4
PP 4
QQ 4
Tipping restraint hardware kit
Bolt M4 × 12 mm
Bolt M4 × 30 mm
Bolt M5 × 12 mm
Bolt M5 × 30 mm
Bolt M6 × 12 mm
Bolt M6 × 35 mm
Bolt M8 × 16 mm
Bolt M8 × 20 mm
Bolt M8 × 40 mm
Label Hardware Qty.
RR 4
SS 4
TT 4
UU 4
VV 4
WW 4
XX 4
YY 8
ZZ 4
Bolt M8 × 50 mm
Lock washer M4
Lock washer M5
Lock washer M6
Lock washer M8
Large spacer
Small spacer
Flat washer M4/M5
Flat washer M6/M8
10 20 30 40 50 60 70 80 90 100mm
1234in
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 6 Tuesday, March 7, 2017 3:08 PM

7
3-in-1 TV STAND
www.insigniaproducts.com
ASSEMBLY INSTRUCTIONS
Step 1: Attach the back stretchers between the side frames
Tip: Assemble your stand on a carpeted floor or the empty TV stand carton to avoid scratching it.
1Insert four 1 5/8" bolts (U), with lock washers (W) and flat washers (X), through the drilled holes on the left side
frame (A) and screw them into the threaded holes on the side of the back stretchers (G) with the 4 mm hex key
(EE). Make sure that the metal brackets on the back stretchers (G) are located on the front side and faced inward.
2Repeat the same procedure to attach the right side frame (B).
NOTE: Do not fully tighten all bolts until you finish assembling all of the parts. After assembly, go back and fully
tighten all bolts. This will make the assembly easier.
You’ll need:
U(8) W(8) X(8) EE (1)
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 7 Tuesday, March 7, 2017 3:08 PM

8
3-in-1 TV STAND
www.insigniaproducts.com
Step 2: Attach the back panel between the back stretchers
• Using the pilot holes as guide, insert four 10 mm screws (R) through the metal brackets of the back stretchers (G)
and securely screw them into the back panel (L) using a Phillips screwdriver.
Pilot hole
You’ll need:
R(4) Phillips screwdriver
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 8 Tuesday, March 7, 2017 3:08 PM

9
3-in-1 TV STAND
www.insigniaproducts.com
Step 3: Align and attach the top shelf to the side frames
• Insert four 1 5/8” bolts (U), with lock washers (W) and flat washers (X), through the drilled holes on the top rails of
both side frames (Aand B), then securely screw them into the threaded holes on the top shelf (I) using the 4 mm
hex key (EE).
You’ll need:
U(4)
W(4) X(4) EE (1)
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 9 Tuesday, March 7, 2017 3:08 PM

10
3-in-1 TV STAND
www.insigniaproducts.com
Step 4: Align and attach the middle shelf to the side frames
• Insert four 1 5/8” bolts (U), with lock washers (W) and flat washers (X), through the drilled holes on the middle
rails of both side frames (Aand B), then securely screw them into the threaded holes on the middle shelf (J) using
the 4 mm hex key (EE).
You’ll need:
U(4)
W(4) X(4) EE (1)
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 10 Tuesday, March 7, 2017 3:08 PM

11
3-in-1 TV STAND
www.insigniaproducts.com
Step 5: Attach the bottom subframe
• Insert four 5/8” bolts (T), with lock washers (W) and flat washers (X), through the end brackets on the left and
right rails (Eand F), then securely screw them into the threaded holes on the bottom crossbar (D) with the 4 mm
hex key (EE). Make sure that the metal tabs face inward and are flush with each other.
You’ll need:
T(4)
W(4) X(4) EE (1)
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 11 Tuesday, March 7, 2017 3:08 PM

12
3-in-1 TV STAND
www.insigniaproducts.com
Step 6: Attach the bottom subframe to the bottom shelf
1Insert six 5/8” bolts (T), with lock washers (W) and flat washers (X), through the metal tabs on the bottom
crossbar (D) and the side rails (Eand F), then finger tighten them into the threaded holes on the bottom shelf
(K).
2Tighten the bolts (T) with the 4 mm hex key (EE).
You’ll need:
T(6)
W(6) X(6) EE (1)
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 12 Tuesday, March 7, 2017 3:08 PM

13
3-in-1 TV STAND
www.insigniaproducts.com
Step 7: Align and attach the bottom shelf to the side frames
• Insert four 2 1/4” bolts (V), with lock washers (W) and flat washers (X), through the drilled holes on the bottom
rails of both side frames (Aand B), then securely screw them into the threaded holes on the bottom shelf (K) with
the 4 mm hex key (EE).
You’ll need:
V (4)
W(4) X(4) EE (1)
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 13 Tuesday, March 7, 2017 3:08 PM

14
3-in-1 TV STAND
www.insigniaproducts.com
Step 8 : Attach the support legs to the bottom shelf
1Securely screw two support legs (H) into the threaded holes on the back rail of the bottom shelf (K).
2Stand the assembled frame upright.
NOTE: For swivel stand assembly, see “SWIVEL STAND ASSEMBLY INSTRUCTIONS” on page 26. For Wall Mount or
Table Top assembly, continue to the next step.
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 14 Tuesday, March 7, 2017 3:08 PM

15
3-in-1 TV STAND
www.insigniaproducts.com
Step 9 : Attach the cable clips
• Attach two of the cable clips (Q) to the back of the side frames (Aand B) with two 5/8" bolts (T) per cable clip
using the 4 mm hex key (EE).
You’ll need:
Q(2) T(4) EE (1)
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 15 Tuesday, March 7, 2017 3:08 PM

16
3-in-1 TV STAND
www.insigniaproducts.com
FINAL TABLE TOP ASSEMBLY INSTRUCTIONS
Step 10 : Position the TV stand and install the tipping restraint hardware kit
1Position the assembled stand against a wall where you plan to use it.
2Adjust the leveling feet to level the TV stand.
3Follow the instructions printed on the bag containing the tipping restraint hardware kit (GG) to attach the
restraint hardware to the wall and the stand.
WARNING: It is very important that the tipping restraint be installed correctly. Failure to do this could result in your
TV/stand assembly falling forward, resulting in damage to equipment or personal injury.
Anchor
Anchor
Wall
Wall
Wall
Bolt
Long screw
Leveling feet
You’ll need:
GG (1)
Power drill
3/8” masonry or
wood drill bit Level
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 16 Tuesday, March 7, 2017 3:08 PM

17
3-in-1 TV STAND
www.insigniaproducts.com
WALL MOUNT ASSEMBLY INSTRUCTIONS
Step 1: Select the correct bolts, washers, and spacers for your TV.
If you are in doubt about which size bolt to use, try one of the bolts in one of the four Vesa mounting holes on the
back of your TV. A bolt that is too large will be obvious and not fit in the hole at all, but make sure that the bolt size
you choose is not too loose. It should grip the hole threads evenly and not wobble. After you determine which size
bolts to use, go on to the next step.
M4 hardware assembly:
•M4 x 12 mm bolts (HH) top screw holes
•M4 x 30 mm bolts (II) bottom screw holes
•M4 lock washers (SS)
•M4/M5 Flat washers (YY)
•Small spacers (XX)
M5 hardware assembly:
•M5 x 12 mm bolts (JJ) top screw holes
•M5 x 30 mm bolts (KK) bottom screw holes
•M5 lock washers (TT)
•M4/M5 flat washers (YY)
•Small spacers (XX)
M6 hardware assembly:
•M6 x 12 mm bolts (LL) top screw holes
•M6 x 35 mm bolts (MM) bottom screw holes
•M6 lock washers (UU)
•M6/M8 flat washers (ZZ)
•Large spacers (WW)
M8 hardware assembly:
•M8 x 16 mm bolts (NN) or M8 x 20 mm bolts (PP) top screw holes
•M8 x 40 bolts (QQ) or M8 x 50 bolts (RR) bottom screw holes
•M8 lock washers (VV)
•M6/M8 flat washers (ZZ)
•Large spacers (WW)
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 17 Tuesday, March 7, 2017 3:08 PM

18
3-in-1 TV STAND
www.insigniaproducts.com
Step 2: Determine whether your TV has a flat back or an irregular or obstructed
back or a curved screen
1Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from damages
and scratches.
2If your TV has a table-top stand attached, remove the stand. See the documentation that came with your TV for
instructions.
3Temporarily lay the TV brackets (P) vertically on the back of your TV.
4Align the screw holes in the TV brackets with the mounting screw holes on your TV.
5Identify which type of back your TV may have:
•Flat back: The brackets lay flush against the back of your TV and do not block any jacks. You do not need spacers
when assembling the wall mount.
•Obstructed back: The brackets block any of the jacks on the back of your TV. You will need spacers when
assembling the wall mount.
•Irregularly-shaped back or curved screen TVs: There is a gap between the bracket and some part of the back of
your TV. You will need spacers when assembling the wall mount.
6Remove the brackets.
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 18 Tuesday, March 7, 2017 3:08 PM

19
3-in-1 TV STAND
www.insigniaproducts.com
Step 3 : Option 1 - Mounting bracket instructions for a TV with a flat back
To mount the TV brackets:
1Insert the selected bolts through the washers and proper mounting holes on the TV brackets (P) (for the 100 x
100 mm vesa pattern you’ll need to lift the bracket hangers to insert the screws), then finger tighten them into
the threaded holes on the back of your TV. Make sure the TV brackets are centered and level with each other
and the hooks face the bottom of the TV.
NOTE: Lean the TV up against a wall or other solid surface when attaching with the TV brackets. DO NOT place the TV
face down on the glass, this may cause permanent damage.
2Tighten the bolts until they are snug against the TV bracket using a Phillips screwdriver. DO NOT over tighten.
JJ LL NN PP
ZZ
UU VVTT
UU VVTT
YY
SS
ZZ
HH
YY
SS
JJ LL NN PPHH
JJ LL NN
UU VV
ZZ
TT
PPHH
SS
YY
or
or
or
or
or
or
or
or
or
Installing the mounting brackets for the 100 x 100 mm vesa hole pattern
You’ll need:
HH (4)
or or or
Bolts & Washers
JJ (4) LL (4) NN (4)
SS (4) TT (4) UU (4) VV (4)
or or or
YY (4) ZZ (4)
or
Phillips screwdriver
Level
P TV brackets (2)
PP (4)
or
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 19 Tuesday, March 7, 2017 3:08 PM

20
3-in-1 TV STAND
www.insigniaproducts.com
Step 3 : Option 2 - Mounting bracket instructions for a TV with an irregularly
shaped or obstructed back or curved screen TVs.
1Insert the selected bolts through the washers and proper mounting holes on the TV brackets (P) (for the 100 x
100 mm vesa pattern you’ll need to lift the bracket hangers to insert the screws), then finger tighten them into
the threaded holes on the back of your TV. Make sure the TV brackets are centered and level with each other
and the hooks face the bottom of the TV.
NOTE: Lean the TV up against a wall or other solid surface when attaching with the TV brackets. DO NOT place the TV
face down on the glass, this may cause permanent damage.
2Tighten the bolts until they are snug against the TV bracket using a Phillips screwdriver. DO NOT over tighten.
JJ LL NN PP
JJ LL NN PP
YY
YY ZZ
UU VVTT
TT
WW
XX
HH
SS
WW
UU VV
HH
ZZ
SS
XX
WW
ZZ
KK MM QQ RR
TT
UU VV
XX
YY
II
SS
or
or
or
or
or
or
or
or
or
or
or
or
or
Installing the mounting brackets for the 100 x 100 mm vesa hole pattern
You’ll need:
II (4)
or or
Bolts & Washers
KK (4) MM (4)
QQ (4)
SS (4) TT (4) UU (4) VV (4)
or or or
YY (4) ZZ (4)
or
Phillips screwdriver
Level
P TV brackets L/R (2)
XX (4)
WW (4)
or
or
RR (4)
NS-HWMC1848_17-0157_MAN_V4_ENG.fm Page 20 Tuesday, March 7, 2017 3:08 PM