Insignia NS-SDSK-BL User manual

QUICK SETUP GUIDE
Standing Desk
NS-SDSK-BL / NS-SDSK-MH
MAJOR PARTS LIST
SMALL PARTS LIST
No. Part Qty
A 2
B 4
C 8
D 1
M6 x16
ST4.2*19
M6×16
4 x 4 5 x 5
No. Part Qty
1 1
2 1
3 1
4 2
5 1
6 1
7 1
8 4
Tabletop
Left column
Right column
Feet
Power Plug
Adapter
Cable ties
Hand switch
D
C
x 8
A
D
x 2
5 x 5
4 x 4
x 4
4 x 4
C
FEATURES
• Easily adjusted to a comfortable height with a hand switch
• 19.7 in (50 cm) of height adjustment lets you use the desk while standing or sitting
• The desktop will hold up to 110 lb. and is suitable for a computer, printer, or
sewing machine (within the weight limit)
• Cable management for a clean look
• Choice of two colors, black or mahogany (both with black frame)
• Electric adjustment switch easily raises or lowers the desk height
• Steel frame with particleboard tabletop provides a stable work surface
D
Before using your new product, please read these instructions to prevent any damage.
PACKAGE CONTENTS
• Standing desk
• Small parts list
• Quick Setup Guide
Top view
D
INSTALLING THE LEGS
1Place the desktop upside down on a carpet or protective cloth.
Note: Make sure that both legs are at their lowest setting
(turn the shaft in each leg to do this) before installation
so that the table will be level when assembled.
2 Insert the hexagonal shaft in the rst leg into the corresponding hole in
the desktop leg mount, then turn the leg until the screw holes line up and the
connecting cable on the top of the leg faces the in toward the motor.
3Attach the leg to the desktop with four M6 x 16 screws, tightening them
rmly with the 4 x 4 Allen key.
4Repeat the steps to attach the other leg .
Note: See the section on "Installing the Adapter and Connecting the Cables"
for cable connections.
D
C
8
Adjustable pad
Hand switch
D
B
2
2
A
INSTALLING THE FEET
Attach the feet to the bottoms of the legs with four 6 x 16 screws each. Make
sure that the adjustable pads on the bottom of the feet face down and
the long portion of each foot faces forward (as shown).
INSTALLING THE SWITCH
Attach the switch to the bottom of the desktop with two ST4.2*19 screws. Tighten
the screws with the 5 x 5 Allen key. Make sure that the at side of the switch is
against the desktop and the UP and DOWN buttons are facing forward.
B
TWO PERSON
LIFT REQUIRED
NS-SDSK-BL_NS-SDSK-MH_20-0373_QSG_V1_EN_Final.ai 1 8/6/2020 11:34:04 AM

V1 ENGLISH 20-0373
LEGAL NOTICES
FCC PART 15
This device complies with Part 15 of the FCC Rules.
Operation of this product is subject to the following two
conditions:
(1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply within
the limits for a class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
• Consult the dealer or an experienced technician for help.
FCC WARNING
Changes or modications not expressly approved by the party
responsible for compliance with the FCC Rules could void the
user’s authority to operate this equipment.
ONE-YEAR LIMITED WARRANTY
For complete warranty, visit www.insigniaproducts.com.
CONTACT INSIGNIA
1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated companies
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2020 Best Buy. All rights reserved.
UP button DOWN button
INSTALLING THE ADAPTER AND CONNECTING THE CABLES
1 Slide the adapter (6) into the slot on the bottom of the desktop so that the female connector is on the
left (as shown) and the adapter cable Is on the right (see detail).
2Connect the cable from the switch to the adapter cable (6), then lock them together (see detail).
3Plug the small connecter on power cord into the female connector on the adapter (see detail)
4Connect the cables from the motor and the right leg to the pre-installed cables on the bottom of the
desktop (see detail).
5Attach the cables to the bottom of the desktop with the cable ties provided (see detail).
USING YOUR STANDING DESK
1 With another person to assist you, lift the desk from the oor and turn it upright.
2 Place the desk where you want it, on a rm, level oor.
3Plug your desk into a power outlet
4Press the to raise the desktop and press the to lower the table top.
Note: Make sure the table and surrounding area are clear from obstructions before moving the
table up or down.
SPECIFICATIONS
•Maximum weight: 110 lbs (50 kg)
•Input voltage required: 100-240 v ~ 50/60 Hz
•Lowest position: 28.7 in. (73 cm)
•Highest position: 48.4 in. (123 cm)
•Dimensions (desktop size) (H×W×D): 47.2 x 23.6 x 0.7 in. (120 x 60 x 1.8 cm)
TROUBLESHOOTING
Problem
The tabletop will not raise or lower
• Make sure that all cables are securely connected.
• Make sure that the tabletop is not overloaded.
• The maximum weight should not exceed 110 lbs. (50 kg).
• Try again after 30 minutes.
• Contact your supplier or dealer.
IMPORTANT SAFETY INFORMATION
• You should only use your table when the temperature is between 32 - 104  F (0-40  C).
• The power adapter requires 100-240 VAC ~ 50/60 Hz.
• Do not expose the power adapter to moisture, or excessive dust. It may cause shock hazards.
• Operate the adapter in a well ventilated area. Maximum ambient temperature around the power
adapter must not exceed 104° F (40° C).
• Do not open the power adapter under any circumstances. The power adapter is not intended to be
repaired in case of failure or component defect. There are no internal serviceable parts.
• Discontinue use, if any of the following should occur:
The adapter shuts down when it connects to the switch’s port. (LED turns o)
The adapter's LED light blinks when the adapter is plugged into an AC power outlet.
A cord or plug is damaged or frayed.
• Make sure to connect the adapter’s plug and switch’s port correctly.
• The socket shall be installed near the adapter and shall be easily accessible.
• Make sure that your table is correctly and completely assembled before you use it.
CAUTION: You should unplug the power cord before cleaning your table. Wipe the dust from the
surface with a slightly damp cloth. Do not use caustic or abrasive cleaners or any solvents
(such as benzine or gasoline) to clean your table.
CAUTION: Children should not be allowed to operate the table.
8
NS-SDSK-BL_NS-SDSK-MH_20-0373_QSG_V1_EN_Final.ai 2 8/6/2020 11:34:05 AM