Insportline ProfiGym C30 User manual

USER MANUAL - EN
IN 18407 Home Gym inSPORTline ProfiGym C30

2
OBSAH
SAFETY INSRUCTIONS......................................................................................................................... 3
PACKAGE ............................................................................................................................................... 3
DISPOSAL............................................................................................................................................... 3
ILLUSTRATED PARTS LIST (1)............................................................................................................. 4
PARTS (1) ............................................................................................................................................... 5
ILLUSTRATED PARTS LIST (2)............................................................................................................. 6
PARTS (2) ............................................................................................................................................... 7
ASSEMBLY ............................................................................................................................................. 8
TRAINING INSTRUCTIONS ................................................................................................................. 14
EXERCISE............................................................................................................................................. 15
MAINTENANCE AND STORAGE......................................................................................................... 16
ENVIRONMENT PROTECTION ........................................................................................................... 16
TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS................................................. 16

3
SAFETY INSRUCTIONS
IMPORTANT!
•This device is made for home use and the weight of the user should not exceed 120 kg.
•Use this product as intended. Improper use of the device can lead to injury. The manufacturer
is not responsible for any damage to health or property resulting from improper use of the
device.
WARNING:
1. This device is made with latest norms and regulations to reduce the risk of injury. Device can
be use only by adults.
2. Improper or excessive training can lead to health problems. Before you start any training,
program visit your physician. Build your training program with the help of your physician.
3. For safety do not allow kids or pets around this device. Manufacturer is not responsible for
injures or damaged caused by unpredictable satiations.
4. Kids can use this device when they are familiar with safety precautions and how to exercise.
5. Device can be build by adult only. Place the device on flat and solid surface. Use the device
only when you finish the construction.
6. When you exercise for long periods of time, it is recommended to check all parts every month.
(especially fasteners)
7. Immediately replace all worn or damaged parts.
8. Always make sure that all adjustable parts are properly secured.
9. During exercise use suitable cloths and boots.
PACKAGE
The package is made of environment-friendly and recyclable materials:
•Outer packing cardboard
•Filling is made of Polystyrol (PS no FCKW)
•Foils and bags are made of PE
•Girths are made of PP
DISPOSAL
Please dispose packaging properly. Don’t put it in the garbage.

4
ILLUSTRATED PARTS LIST (1)

5
PARTS (1)
NO.
NAME
QTY
A
Main frame
1
B
Rear base
1
C
Main vertical frame
1
D
Guide rod
2
E
Top cross beam
1
F
Seat support
1
G
Press bar
1
H
Right chest support
1
I
Left chest support
1
J
Front base
1
K
Leg extension
1
L
Foam tube
2
M
Iron bushing
2
N
Resist bar
1
O
Lower handrail
1
P
Pull bar
1
Q
Handle bar
2
R
Selector shaft
1
S
Upright pulley block
1
T
Parallel pulley block
2
U
Rotational pulley block
2
V
Reinforced plate
3
W
Weight plate
9
X
Top plate
1
Y
Pulley
13
Z
Lock lever
1
AA
Bushing
10

6
ILLUSTRATED PARTS LIST (2)

7
PARTS (2)
NO.
NAME
QTY
1
Backrest cushion
1
2
Headrest cushion
1
3
Seat cushion
1
4
Big foam roller
2
5
Foam roller
4
6
Cable with no ball
1
7
Long cable with one ball
1
8
Short cable with one ball
1
9
Rubber donut
2
10
Pin
1
11
Hook
5
12
Chain
2
13
Bolt m12×165 + washers + lock nuts
1
14
Bolt m6*16 + washer
4
15
Bolt m8*16 + bend washer
4
16
Bolt m8*35 + bend washer
2
17
Bolt m8×40 + two washers + lock nut
1
18
Bolt m8*80 + bend washer
4
19
Bolt m12×20 + bend washer
2
20
Bolt m10×35 + lock nut
1
21
Bolt m10×50 + two washers + lock nut
8
22
Bolt m10×60 + two washers + lock nut
2
23
Bolt m10×70 + two washers + lock nut
2
24
Square neck bolt m10×75
2
25
Bolt m10×75 + bend washer
2
26
Bolt m10×80 + two washers + lock nut
5
27
Bolt m10×80 + bend washers + lock nut
8
28
Bolt m10×85 + two washers + lock nut
1
29
M8 lock nut
2
30
M12 lock nut + big washer
2

8
ASSEMBLY
STEP 1
1．Attach rear base (B) to main frame (A) with four bolts M8*16 + bend washers (15).
2．Attach seat support (F) to front base (J) with two bolts M10*60 + washers + lock nuts (22).
3．Attach seat support (F) and reinforcement plate (V) to main frame (A) with two bolts M10*80 +
bend washers + lock nuts (27).
4．Insert guide rod (D) into rear base (B) and secure with square neck bolt M10*75 (24).
5．Slide rubber donut (9) and weight plates (W) onto guide rod (D), insert selector shaft (R) into mid
hole of weight plate (W). Then slide top plate (X) onto guide rod (D).
6．Attach leg extension (K) to main frame (A) with blot M10*85 + washers + lock nut (28).
7．Attach pulleys (Y) to main frame (A), seat support (F) and leg extension (K) with blot M10*80 +
washers + lock nut (26) and bushing (AA).

9
STEP 2
1．Attach main vertical frame (C) and reinforcement plate (V) to main frame (A) with two bolts
M10*80 + bend washers + lock nut (27).
2．Attach top cross beam (E) and reinforcement plate (V) to main frame (C) with two bolts M10*80 +
bend washers + lock nuts (27).
3．Attach guide rod (D) to top cross beam (E) with two bolts M10*75 + bend washers (25).
4．Attach rotational pulley block (U) to main vertical frame (C) with two blots M10*70 + washers +
lock nuts (23).
5．Attach resist bar (N) to main vertical frame (C) with two bolts M10*80 + bend washers + lock nuts
(27).
6．Attach lock lever tus (Z) to resist bar (N) with bolt M8*40 + washers + lock nut (17).
7．Attach one pulley (Y) to front of top cross beam (E) with blot M10*80 + washers + lock nut (26)
and bushing (AA).
8．Attach pulleys (Y) to top cross beam (E) and rotational pulley block (U) with bolt M10*50 +
washers + lock nut (21).

10
STEP 3
1．Attach press bar (G) to top cross beam (E) with bolt M12*165 + washers + lock nuts (13).
2．Attach right and left chest support (H&I) to press bar (G) with M12 lock nut + big washer (30).
3．Push big foam roller (4) onto right and left chest support (H&I).
4．Secure handle bar (Q) to right and left chest support (H&I) with two bolts M12*20 + bend washers
(19) and two bolts M8*35 + bend washers (16).