Target osa DA7874 User manual

style # DA7874
DA7874W
dpci # 249/24/2227
249/24/2229
>>assembly instructions
osa
twin over twin bunk bed

Congratulations on your latest Target purchase.
Now what? Don't start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you'll be on your way to transforming your
room in no time. Good luck-though we're confident you won't need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
2

table of contents
introduction 2
hardware 4
parts list 5-7
assembly 8-17
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846). For faster service, have the style number and DPCI number ready when calling. 3

hardware (H1) x 16 (H2) x 8
joint connector (4mm hex head) wood joint connector (4mm hex head)
1/4" x 100mm ø6.5 x 48mm
(H3) x 24 (H4) x 24
wood joint connector (4mm hex head) flat head screw
ø6.5 x 100mm ø4 x 35mm
(H5) x 6 (H6) x 4
flat head screw metal dowels
ø4 x 30mm ø10 x 100mm
(H7) x 30 (H8) x 16
small wood dowel barrel nut
ø10 x 50mm ø11.8 x 15mm
(H9) x 1
allen key
4mm
4

ITEM DESCRIPTION QUANTITY
A top post 2
B top post 1
C top post 1
D bottom post 2
E bottom post 2
F top headboard top rail 2
G headboard bottom rail 4
H top side rail (with 3 holes) 1
I bottom side rail (with 2 holes) 1
J top side rail (with 1 hole) 1
K bottom side rail (with no hole) 2
L slat 12
M long guardrail 2
N short guardrail 2
O long ladder end 1
P short ladder end 1
Q ladder step 4
R guardrail leg 2
S headboard panel 4
T slat 4
U bottom headboard top rail 2
5

A B C D
E F G H
I J K L
6
slat
12 pcs
top post
2 pcs
top post
1 pc
bottom post
2 pcs
bottom side rail (with 2 holes)
1 pc
bottom post
2 pcs
top side rail (with 3 holes)
1 pc
headboard bottom rail
4 pcs
top headboard top rail
2 pcs
top side rail (with 1 hole)
1 pc
top post
1 pc
bottom side rail (with no hole)
2 pcs

M N O P
Q R S T
U
7
long guardrail
2 pcs
short guardrail
2 pcs
long ladder end
1 pc
short ladder end
1 pc
slats
4 pcs
bottom headboard top rail
2 pcs
ladder step
4 pcs
guardrail leg
2 pcs
headboard panel
4 pcs

step 1.
(H7) x 8
Top Bed Head and Footboard
3. Attach the headboard top rail (F) to top posts (A & B) with wood joint connectors (H3) using allen key (H9).
8
(H3) x 8
wood joint connector (4mm hex head)
ø6.5 x 100mm
1. Insert small wood dowels (H7) into the ends of top posts (A & B) and headboard bottom rail (G).
2. Slide headboard panel (S) into the grooves of the headboard bottom rail (G). Attach headboard bottom rail (G) to posts (A & B) using wood
joint connectors (H3) and allen key (H9).
NOTE: One of the headboard panels (S) has a warning on it. Use the panel with the label between top posts (A) and (B).
See illustration for label orientation.
small wood dowel
ø10 x 50mm
4. Repeat this step to assemble other headboard using top posts (A & C).

step 2.
(H7) x 8
(H3) x 8
wood joint connector (4mm hex head)
ø6.5 x 100mm
Bottom Bed Head and Footboard
3. Attach bottom headboard top rail (U) to posts (D & E) with wood joint connectors (H3) using allen key (H9).
9
small wood dowel
ø10 x 50mm
4. Repeat this step to assemble other headboard.
1. Insert small wood dowels (H7) into the ends of bottom posts (D & E) and headboard bottom rail (G).
2. Insert headboard panel (S) into the grooves of headboard bottom rail (G). Attach headboard bottom rail (G) to posts (D & E)
using wood joint connectors (H3) and allen key (H9).

step 3.
10
NOTE: This is the lower bunk.
(H1) x 8
joint connector (4mm hex head)
1/4" x 100mm
ø11.8 x 15mm
Bottom Bed Assembly
1. Insert barrel nuts (8) into side rails (I & K) as shown.
2. Attach two bottom headboards assembled in Step 2 to the bottom side rails (I & K) with joint connectors (H1) and allen key (H9).
(H8) x 8
barrel nut

step 4.
11
NOTE: This is the upper bunk.
2. Insert small wood dowels (H7) into each end of the long guardrails (M).
3. Attach two long guardrails (M) and two top side rails (H & J) to the top posts (A, B and C) as shown.
4. Fasten top side rails (H & J) with joint connectors (H1) using allen key (H9).
5. Fasten long guardrails (M) with wood joint connectors (H3) using allen key (H9).
1. Insert barrel nuts (H8) to the top side rails (H & J).
Top Bed Assembly
small wood dowel
ø10 x 50mm
joint connector (4mm hex head)
1/4" x 100mm
barrel nut
ø11.8 x 15mm
(H7) x 4
(H1) x 8
(H3) x 4
wood joint connector (4mm hex head)
ø6.5 x 100mm
(H8) x 8

step 5.
(H4) x 24
flat head screw
ø4 x 35mm
Bottom Bed Assembly
12
3. Secure slats (L) to the bottom side rails (I & K) with flat head screws (H4) using a Phillips head screwdriver (not included).
4. Repeat this step to attach slats (T & L) to the upper bunk.
NOTE: If you notice that any slats (L) are not perfectly flat, be sure to assemble them so that slat (L) curves up in the middle and down at the ends.
1. Insert two slats (T) into the center slots of the bottom side rails (I & K) of the lower bunk bed as shown.
2. Insert slats (L) into the remaining holes on the bottom side rails (I & K).

step 6.
13
small wood dowel
ø10 x 50mm
ø4 x 30mm
2. Attach the guardrail legs (R) to the top side rails (H & J) and guardrails (M & N) with flat head screws (H5) using a Phillips screwdriver (not included).
3. Insert the metal dowels (H6) into the holes in the bottom headboard top cross (U).
ø10 x 100mm
(H3) x 2
wood joint connector (4mm hex head)
ø6.5 x 100mm
4. Stack the top bunk onto the bottom bunk with the help of another person.
1. Attach the short guardrails (N) to the top post (A) with wood joint connectors (H3) using allen key (H9).
(H6) x 4
(H7) x 4
(H5) x 6
flat head screw
metal dowels

step 7.
wood joint connector (4mm hex head)
14
Ladder Assembly
1. Insert small wood dowels (H7) into the end of the ladder steps (Q).
ø10 x 50mm
(H2) x 8
ø6.5 x 48mm
small wood dowel
(H7) x 8
2. Attach left and right ladder end (O & P) to ladder steps (Q) with wood joint connectors (H2).
Tighten the wood joint connectors (H2) with allen key (H9).

step 8.
wood joint connector (4mm hex head)
15
NOTE: If slats (L) are covering the ladder mounting holes, remove slats (L) and replace after the ladder is attached.
(H2) x 6
ø6.5 x 48mm
1. Attach the ladder to short guardrails (N) and top side rail (H) with wood joint connector (H2) using a Phillips screwdriver (not included).

converting bunk bed into two single beds.
16
2 With the help of another person, lift the upper bunk and put it on the floor.
1. Remove the ladder and all guardrails.

17
DO NOT ALLOW CHILDREN UNDER
6 YEARS OF AGE TO USE THE
UPPER BUNK. BED IS DESIGNED
FOR CHILDREN RANGING FROM 6
YEARS OF AGE TO YOUNG
TEENAGERS.
USE ONLY COIL SPRING
MATTRESSES ON BOTH THE UPPER
AND LOWER BUNKS. FAILURE TO
DO SO CAN RESULT IN INJURY.
USE ONLY MATTRESSES WHICH ARE
74"-75" LONG AND 37 1/2" - 38 1/2" WIDE
ON UPPER BUNK AND AT LEAST 27 1/4"
BY 51 5/8" ON LOWER BUNK. ENSURE
THICKNESS OF MATTRESS DOES NOT
EXCEED 6".
DO NOT ALLOW HORSEPLAY ON OR
UNDER THE BED AND PROHIBIT
JUMPING ON THE BED.

© 2017 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.