Intelbras IVP 2000 SF User manual

User manual
IVP 2000 SF

IVP 2000 SF
Infrared sensor
Congratulations, you have just purchased a product with Intelbras quality and safety.
The IVP 2000 SF passive infrared sensor was developed by Intelbras with 100% di-
gital technology. This sensor has SMD technology, offers efcient detection with redu-
ced risk of false shots, and has automatic temperature compensation. It is compatible
with most devices on the market that work at the same frequency and modulation.

Summary
1. Technical specications 4
2. Installation 4
3. Tests 5
4. Sensor variety 6
Warranty term 7

4
1. Technical specications
Angle of detection 90º wide angle
Detection range Up to 12 m
Voltage 9 Vdc battery
Consumption: 25 mA at 9 Vdc
Temp. oper. -10 ° C to 50 ° C
Frequency 433.92 MHz
Modulation OOK
Baud rate 2 KBps (open source)
Homologation:
According to the applicable Anatel regulation, this equipment is intended to operate on a secondary basis, that is, it is not entitled to protection against harmful interfe-
rence, even from stations of the same type, and cannot cause interference to systems operating on a primary basis.
2. Installation
Open the front cover of the sensor (by pressing on the sides).
Connect a 9 V battery to the existing connector and program the code on the receiver as explained in the manual of the
control panel used.
The IVP 2000 SF does not need to be installed with an articulator, as it already has a 12° tilt angle. The scanning angle
is 90° and the range is up to 12 m. If necessary, adjust the tilt angle of the scan beam by moving the sensor plate up or
down, as needed. The recommended installation height is 2.2 m.
Important: the IVP 2000 SF is designed for indoor and closed areas, so it should not be used to protect outside or open
areas.
Wireless communication technology, when exposed to environments with high-power radiation, can suffer interference
and have its performance impaired. Example: locations near TV towers,AM / FM radio stations, amateur radio stations, etc.
Do not install the sensor facing air conditioners or heaters.
Avoid direct sunlight, vapors and high humidity on the sensor.
Also avoid curtains, screens or any object that may block your scanning beam.
Check in advance the characteristics of the product in which the sensor will be registered, in order to avoid incompatibilities.

5
3. Tests
After inserting the battery, the LED will blink for approximately 20 seconds (stabilization time and self-test). When it goes
out, the sensor will operate for 10 minutes in Continuous mode (immediate trigger). After 10 minutes, the sensor will start
operating in Economy mode.
When the sensor trips while in Economic mode, it is necessary to wait two minutes without moving for it to detect again.
Advantage of Economy mode: in environments where there is a large circulation of people, Economy mode will reduce
excessive battery consumption.
For a better understanding of the Economy mode, observe the following timeline.
1. Apresentação
O sensor de infravermelho passivo IVP 2000 SF foi desenvolvido pela Intelbras com
tecnologia 100% digital. Esse sensor possui tecnologia SMD, oferece uma detecção
ção automática
de temperatura. Ele é compatível com a maioria das centrais de alarme existentes
no mercado.
2.
Cobertura Grande angular 90º
Alcance Até 12m
Alimentação Bateria 9 Vdc
Consumo: 25 mA em 9 Vdc
Temp. oper.: -10 °C a 50 °C
Frequência: 433.92 MHz
Homologação:
Conforme regulamentação Anatel aplicável, este equipamento é previsto para operar
em caráter secundário, isto é, não tem direito à proteção contra interferência prejudicial,
mesmo de estações do mesmo tipo, e não pode cusar interferência a sistemas operando
em caráter primário.
3. Instalação
Abra a tampa frontal do sensor(pressionando as laterais).
Ligue uma bateria 9 V no conector existente e programe o código no receptor
conforme explicado no manual da central de alarme utilizada.
O IVP 2000 SF não necessita ser instalado com articulador, pois já possui um ângulo
de inclinação de 12°. O ângulo de varredura é de 90° e o alcance é de até 12 m. Se
necessário, ajuste o ângulo de inclinação do feixe de varredura movendo a placa do
sensor para cima ou para baixo, conforme sua necessidade. A altura de instalação
recomendada é de 2,2 m.
Importante: OIVP 2000 SF foi projetado para áreas internas e fechadas, portanto,
não deve ser utilizado para proteção de áreas externas ouabertas.
potência elevada, pode sofrer interferências e ter seu desempenho prejudicado. Exemplo:
locais próximos a torres de TV, estações de rádioAM/FM, estações de rádios amadores, etc.
Não instaleo sensor voltado para aparelhos de ar condicionado ouaquecedores.
Evite luz solar direta, vapores e umidadealta sobre o sensor.
Evite também cortinas, telas, biombos, ou qualquer objeto que possa barrar o seu
feixede varredura.
4. Testes
de estabilização e realização de autoteste). Quando este se apagar, o sensor operará por
10 minutos em modo
Contínuo
(disparo imediato). Após o tempo de 10 minutos o
sensor passará a funcionar no modo
Econômico
.
Quando o sensor disparar estando no modo
Econômico
, é necessário aguardar um
tempo de dois minutos sem movimentação para que ele volte a detectar.
Vantagem do modo
Econômico
: em ambientes onde há grande circulação de pessoas,
o modo
Econômico
reduzirá o consumo excessivo da bateria.
Para melhor entendimento do modo
Econômico
10 min
Após colocar
abateria osensor
no modo de
estabilização eo
LED
piscando. Obs:
Não cadastre o
sensor na central
neste periodo,
aguarde os 20 seg
para que osensor
entre no modo
continuo.
Não
detecta
Neste modo
qualquer
detecção o
LED acende
egera
disparo
Modo
estabili-
zação
20 seg
Modo
continuo
Tempo que osensor
permanecer ligado.
Modo economico
Neste modo o
sensor detecta
oprimeiro mo-
vimento egera
disparo,porem
ele entra em
hibernação e
volta adetectar
depois de dois
minutos sem
movimento no
local, no periodo
dehibernação o
LED não acende
2 min
Neste periodo
de 2 min se
houver movi-
mento no
local osensor
espera aúlti-
ma movimen-
tação para
começar a
contar os dois
minutos.
Passados os
2 minutos
da última
movimentação
do local o
sensor volta
adetectar e
gerar disparo
na central.
Continuous mode
10 minutes
Does
not detect
Stabilization
mode
20 sec.
Economic mode
Sensor time
stay connected
2 min.
Para testar, ande lentamente em frente ao sensor observando se o LED acende em
toda a área que precisa ser protegida. Se necessário, reajuste a posição do sensor.
Caso necessite de mais tempo para testar o sensor, desligue a bateria, espere por
20 segundos e ligue a bateria novamente.
Se a central de alarme utilizada for Intelbras, coloque-a no modo
Teste
. Dessa maneira
não será necessário observar o LED, pois a central indicará o funcionamento do sensor
através de bipes da sirene.
Caso deseje diminuir a sensibilidade, mude o jumper JP2 (ajuste de sensibilidade)
para a posição 2-3.
Após os testes, pode-se desligar o LED para economizar bateria através do jumper JP1.
Sensor de bateria baixa:
nível da bateria está crítico (+/- 7 V), envia um código para a central de alarme. Se a
central de alarme é Intelbras, o aviso de nível baixo de bateria será indicado no painel.
Modelos com essa função: ANM 2004/2008 MF, AMT 2008 RF 2010/2018/2018
EG, AMT 4010 Smart e AMT 4010 Smart Net.
Obs.: caso no momento do cadastro o sensor esteja no modo
Econômico
siga os
seguintes passos.
1. Retire a bateria e coloque novamente (o LED começará a piscar);
2. Aguarde o apagamento total do LED (aproximadamente 20 segundos);
3. Após a estabilização o sensor está pronto para o cadastro.
5. Varredura do sensor
2,4 m
5,2 m10,7 m21,3 m
90°
R 5,2 m
R 2,4 m
R 10,7 m
R 21,3 m
Varredura
After inserting the battery,
the sensor is in
stabilization mode and
the LED blinks.
Note: Do not register the
sensor on the control
panel in this period, wait
20 seconds for the sensor
to enter continuous mode.
In this mode, any
detection, the LED
lights up and
generates a
trigger.
In this mode, the
sensor detects the rst
movement and
generates a trigger,
however, it goes into
hibernation and
detects again after
two minutes with no
movement in place, in
the dehydration
period, the LED does
not light up.
In this 2 minute
period, if there is
movement in
place, the sensor
waits for the last
movement to start
counting the 2
minutes.
After 2 minutes
from the last site
movement, the
sensor detects and
generates a trigger
on the control
panel.
To test, walk slowly in front of the sensor to see if the LED lights up in the entire area that needs to be protected. If ne-
cessary, readjust the position of the sensor. If you need more time to test the sensor, disconnect the battery, wait for 20
seconds and then connect the battery again.
If the alarm panel used is Intelbras, put it in test mode. In this way, it will not be necessary to observe the LED, as the control
panel will indicate the sensor’s operation through siren beeps.
If you want to decrease the sensitivity, move the JP2 jumper (sensitivity adjustment) to position 2.
To turn off the sensor LED, simply remove the JP1 jumper, in order to save battery.
Low battery sensor: the IVP 2000 SF has a sensor that, when it identies that the battery level is critical (+/- 7 V),
sends a code to the control panel. If the control panel is Intelbras, the low battery warning will be indicated on the panel.
Models with this function: ANM 2004/2008 MF, AMT 2008 RF 2010/2018/2018 EG, AMT 4010 Smart and AMT 4010
Smart Net.

6
4. Sensor variety
2,4 m
5,2 m 10,7 m 21,3 m
90°
R 5,2 m
R 2,4 m
R 10,7 m
R 21,3 m
Scan

7
Warranty term
It is established that this warranty is granted upon the following conditions:
Client’s name:
Client’s signature:
Invoice number:
Date of purchase:
Model: Serial number:
Retailer:
1. All the parts, pieces and components of the product are guaranteed against possible manufacturing defects, which may
arise, for the term of 1 (one) year - this being 90 (ninety) days of legal guarantee and 9 (nine) months contractual warran-
ty –, counting from the date of purchase of the product by the Consumer, as appears in the product purchase bill of sale,
which is an integral part of this Term throughout the domestic territory. This contractual warranty incudes the express
exchange of products which have a manufacturing defect. If there is no manufacturing defect, but defect(s) arising from
misuse, the Consumer shall bear these expenses.
2. The installation of the product shall be executed in accordance with the Product Manual and/or Installation Guide. If your
product requires the installation and conguration by a qualied technician, seek a suitable specialized professional, the
costs of these services not being included in the product amount.
3. Having perceived the defect, the Consumer shall immediately contact the nearest Authorized Service which appears in
the report offered by the manufacturer – they are the only ones authorized to examine and remedy the defect during the
warranty term foreseen herein. If this is not respected, this warranty shall lose its validity, as it shall be characterized as
product infringement.
4. If the Consumer requests home service, it shall contact the nearest Authorized Service to inquire about the technical visit
rate. If it is necessary to remove the product, the ensuing expenses, such as those of transportation and insurance of the
taking and return of the product, shall be the Consumer’s responsibility.
5. The warranty shall lose its validity totally in the occurrence of any of the following cases: a) if the defect is not one of manu-
facture, but is caused by the Consumer or by third parties foreign to the manufacturer; b) if the damage to the product arises
from accidents, disasters, agents of nature (lightning, oods, landslides, etc.), humidity, voltage in the electrical network
(excess voltage caused by accidents or excessive uctuations in the network), installation/use in disagreement with the
user’s manual or arising from natural wear of the parts, pieces and components; c) if the product has undergone effects of a
chemical, electromagnetic, electrical or animal (insects, etc.) nature; d) if the serial number of the product has been falsied
or erased; e) if the appliance has been infringed.
6. This warranty does not cover loss of data; therefore, it is advisable that if it is the case of the product, the Consumer makes
a backup regularly of the data which appears in the product.
7. Intelbras is not responsible for the installation of this product, or for possible attempts at fraud and/or sabotage in its
products. Maintain the updates of the software and applications used up-to-date, if it is the case, as well as the network
protection required for defense against hackers. The equipment is guaranteed against defects in its usual conditions of use,
it being important to bear in mind that, as it is electronic equipment, it Is not free of fraud and scams which may interfere
with its correct functioning.
8. This product has an internal battery/battery. After its useful life, the product must be delivered to an Intelbras authorized
technical assistance or directly perform the nal destination environmentally appropriate avoiding environmental and health
impacts. If you prefer, the battery as well as other Intelbras brand electronics without use, can be disposed of at any collection
point of Green Eletron (manager of electrical and electronic waste with which we are associated). If you have any questions
about the reverse logistics process, please contact us at (48) 2106-0006 or 0800 704 2767 (Monday to Friday from 8am to
8pm and Saturdays from 8 am to 6 pm) or via [e-mail].
These being the conditions of this complementary Warranty Term, Intelbras S/A reserves the right to alter the general,
technical and esthetic features of its products without prior notice.
The manufacturing process of this product is not covered by the requirements of ISO 14001.
All the images of this manual are illustrative.

01.20
Made in Brazil
Customer Support: (48) 2106 0006
Forum: forum.intelbras.com.br
Support via chat: intelbras.com.br/suporte-tecnico
Support via e-mail: [e-mail]
Customer Service: 0800 7042767
Where to buy? Who installs it? 0800 7245115
Produced by: Intelbras S/A – Indústria de Telecomunicação Eletrônica Brasileira
Rodovia BR 459, km 124, 1325 – Distrito Industrial – Santa Rita do Sapucaí/MG – 37540-000
CNPJ 82.901.000/0016-03 – www.intelbras.com.br